Card Master CM500
Technical Manual | Card Master CM500 Product Version: 1.0 Version of this manual: 2.5.1 © 2014 Inepro B.V. All rights reserved
Card Master CM500
Table of Contents Models Introduction Installation Initiation Coin Hoppers Maintenance Function Menu Function Overview Programming example Ticket Dispencers Optional General technical data Troubleshooting VMS-1 Overview
Version 2.5.1 Inepro B.V.
2 4 6 8 10 12 14 18 24 26 28 30 32 34
http://www.inepro.com
Always disconnect the power supply before removing the hoppers/dispensers! Read the manual before switching on this device. Before switching on this device, make sure that the power supply is 220V / 240VAC 50Hz. Your supplier does not take any responsibility if the safety norms are not followed. Always disconnect power supply before handling anything inside the device. Do not use this device without earth connection. The device has to be connected by authorised and fully trained personnel only. After modify or verifying a function always check the machine.
Models
I
Part
Models
Models Ticket dispenser machine models Admits 6 coins and returns 1 type of ticket qCard master CM500 K-1 Admits 6 coins and returns 2 types of tickets qCard master CM500 K-2 Admits 6 coins and returns 1 type of ticket and the change, if qCard master CM500 K1-W necessary Admits bank notes and returns 1 type of ticket qCard master CM500 K1-B Admits bank notes and returns 2 types of tickets qCard master CM500 K2-B qCard master CM500 K1-W-B Admits bank notes and returns 1 type of ticket and the change, if necessary Tick the box of the correct machine.
2
-
Card Master CM500
Introduction
II
Part
Introduction
Introduction This manual contains information about the installation, menu programming and maintenance of the different machines which are controlled by the Vend Master System (VMS) 1, as there are change machines, ticket and token dispensers. All these machines have one thing in common: after inserting a certain amount of coins it returns the amount and/or a product to the value corresponding to that of the amount of inserted coins. As the control systems of the machines described in this manual are similar, all are equipped with VMS-1 circuit boards. The control and programming depend on the software and the model of the machine. General programming is described in this manual. Read this manual carefully to guarantee flawless operation. Always indicate the model and serial number when asking for more information about your machine!! Connection possibilities § One input to connect the coin system or the banknote reader. § Two outputs to control ticket dispensers and/or coin hoppers. The maximum accepted quantity of coins/banknotes depends on the system; the coins/banknote to be accepted are: € 0,05, € 0,10, € 0,20, € 0,50, € 1,00, € 2,00 // € 5,00, € 10,00, € 20,00, € 50,00. The coins to be returned may include any of the above mentioned. When requested the system can be prepared to accept and return other coins or foreign money. Depending on the type of machine, various coin and/or banknotes reader systems can be installed to allow the admittance of different types of coins and/or banknote. Coin system models: § Mechanic coin meter WH-N1, maximum admittance 1 type of coin. § Electronic coin meter WH 800.00, maximum admittance 6 types of coins.
§ § § §
Banknote reader models: Banknote reader Smile Banknote reader CVI (GPT-2/GPT+), always with a banknote stacker Banknote reader Ardac Banknote reader Armatic
Money and/or ticket return units: § Coin hopper Asahi Seiko SA-595 § Ticket dispenser Asahi Seiko CD-200 § Coin-Control hopper C-24/MK-2 Optional: § Shaft elongation pieces to increase the coin or ticket capacity.
4
-
Card Master CM500
Installation
III
Part
Installation
Installation Installation We recommend you to take into account the following points to guarantee correct functioning of the machine: · Install the machine in a visible busy place; · Fix the machine to a solid and smooth wall, or use the optional installation column; · Make sure the machine is perfectly level; · Connect the machine to a clean group with earth connection; · The connection of the machine should be permanent (without socket) or to a wall socket well out of the user’s reach.
6
-
Card Master CM500
Initiation
IV
Part
Initiation
Initiation § § § § §
Switch the machine off. Fill the hopper(s) and/or the dispensers with coins and/or tickets. Switch the machine on. Test the change machine with various types of coins or banknotes. Change the menu if wrong values are returned.
In case you have a machine which returns 2 types of coins / products it is very important that each hopper /dispenser is filled with the correct coins / tickets.
8
-
Card Master CM500
Coin Hoppers
V
Part
Coin Hoppers
The coin hoppers The coin hopper(s) is/are the coin unit(s) of the machine; these have to be filled with coins to guarantee correct functioning of the machine. There are two copper plates, located in the lower part of the hopper, to show when it is empty. These copper plates always have to be covered by coins to avoid the activation of the 'empty' signal. Like this, there are always enough coins left, and you can refill before the 'empty' signal is activated.
10
-
Card Master CM500
Maintenance
VI
Part
Maintenance
Maintenance Preventive maintenance depends on the location of the machine and on how frequently it is used. § The coin hopper(s) do(es) not need any type of maintenance provided that no rubbish (paper etc.) is introduced at filling it/them. § The ticket dispensers require only little maintenance, depending on whether paper or plastic tickets are used. § The electronic and mechanic coin meters can get slightly dirty in dusty places; this may affect the coin admittance. Therefore, the main maintenance measure consists in cleaning the coin shafts with an alcohol based, non-greasy and non-aggressive liquid. § The electronic card reader has to be cleaned quite frequently (depending on how frequently it is used) by means of a special cleaning card to avoid interference with the transactions. We recommend you to contact the supplier of the machine with regard to the maintenance of banknote readers and ticket dispensers; he will inform you about a maintenance contract.
12
-
Card Master CM500
Function Menu
VII
Part
Function Menu
The function-menu Functions of the VMS-1 control system According to the machine model, the “VMS-1” function-menu is accessible for the functions, which are valid for this model; depending on the function it is possible to modify or read programmes. The VMS-1 is programmed by means of three buttons, which are integrated in the main board. By pressing these buttons, the function-menu can be programmed, modified, or read. To activate the function-menu, set the included jumper on its corresponding place on the VMS-1 circuit. The display shows F 00 18 . By means of the three buttons of the circuit board, you can choose, read or change a function. Programming the menu 1) Place the included jumper on the main board, the display will show F 00 2) By means of the Up and Down buttons scroll to the function you wish 3) Press the Function button to read or modify the selected function 4) Modify this value pressing the Up or Down button 4a) To quit the function, press the Function button 5) Remove the jumper to return to the service mode
18
The three buttons are; (from top to bottom) § The Function button, by means of which the current value is shown in the display § The Down button, with this button the current value is modified § The Up button, with this button the current value is modified
14
-
Card Master CM500
The counters The total turnover of the machine is recorded in the “VMS-1”, By this income and expenditure is controlledwithin a defined period. § To control the income, select functions F 32 20 to F 39 20 . Function F 32 20 represents the smallest accepted money unit, function F 33 20 represents the following accepted money unit etc., pressing the function button, the number of accepted coins will be shown in the display. Example A machine accepts € 0,20 to € 2,00 Function F 32 20 represents € 0,20. Function F 35 20 represents € 2,00. If € 0,05 to € 2,00 are accepted, function F 32
20
represents € 0,05 and function F 37
§ To control the quantity of returned coins/products, select function F 42 Function F 42 Function F 43
20 20
20
or F 43
20
20
€ 2,00.
.
represents the hopper/dispenser 1 represents hopper/dispenser 2
Pressing the function button, the number of returned coins/products is shown in the display. Remove the jumper to return to the user mode. Resetting the counters The revenue/coin counters (F 32 20 till F43 20 ) can be reset. To reset the counters, push simultaneously the up and down button. Make sure you do this while the value of the chosen function is shown on the display. While pushing both buttons, the value will change from the current quantity into the value "0". How to empty the hopper(s)/dispenser(s) § To empty the hopper(s)/dispenser(s) select function F 42 20 or F 43 20 (hopper/dispenser 1or 2) in the menu § To empty the hopper, press the lower left button on the circuit board The returned amounts are shown in the display, they are not registered by the VMS-1 return counters! § Press the button again to finish the refund § Remove the service jumper to return to the user mode
Version 2.5.1
-
15
Function Overview
VIII
Part
Function Overview
Functie Overzicht Functie F00, Verkoopprijs 1 Functie Waarde 0-255
Functie F00, Verkoopprijs 1. Munt / productwaarde hopper 1. Omschrijving
Basis waarde
Aantal uitgave uit hopper/dispenser 1 bij munt 1.
Functie F01, Verkoopprijs 1b Functie Waarde 0-255 Note:
Verkoopprijs 1b. Munt / productwaarde hopper 1. Omschrijving
Basis waarde
Aantal uitgave uit hopper/dispenser 1 bij munt 2. Timer Input function, zie Timer Input 21 .
Functie F02, Verkoopprijs 1c Functie Waarde 0-255 Note:
Verkoopprijs 1c. Munt / productwaarde hopper 1. Omschrijving
Basis waarde
Aantal uitgave uit hopper/dispenser 1 bij munt 3. Timer Input function, zie Timer Input 21 .
Functie F03, Verkoopprijs 1d Functie Waarde 0-255 Note:
Verkoopprijs 1d. Munt / productwaarde hopper 1. Omschrijving
Basis waarde
Aantal uitgave uit hopper/dispenser 1 bij munt 4. Timer Input function, zie Timer Input 21 .
Functie F04, Verkoopprijs 2 Functie Waarde 0-255 Note:
Functie F04, Verkoopprijs 1. Munt / productwaarde hopper 2. Omschrijving
Basis waarde
Aantal uitgave uit hopper/dispenser 2 bij munt 1. Timer Input function, zie Timer Input 21 .
Functie F05, Verkoopprijs 2b Functie Waarde 0-255 Note:
Functie F04, Verkoopprijs 1a. Munt / productwaarde hopper 2. Omschrijving
Basis waarde
Aantal uitgave uit hopper/dispenser 2 bij munt 2. Timer Input function, zie Timer Input 21 .
Functie F06, Verkoopprijs 2c Functie Waarde 0-255 Note:
Functie F04, Verkoopprijs 1b. Munt / productwaarde hopper 2. Omschrijving
Basis waarde
Aantal uitgave uit hopper/dispenser 2 bij munt 3. Timer Input function, zie Timer Input 21 .
Functie F07, Verkoopprijs 2d Functie Waarde 0-255 Note:
Functie F04, Verkoopprijs 1c. Munt / productwaarde hopper 2. Omschrijving
Basis waarde
Aantal uitgave uit hopper/dispenser 2 bij munt 4. Timer Input function, zie Timer Input 21 .
Functie F08, Automatische reset tijd van het betalingskrediet Functie Waarde 0-255
Functie F08, Automatische reset tijd van het betalingskrediet . Omschrijving
Basis waarde
Automatische reset tijd van het betalingskrediet (in minuten).
Functie F09, Relais K-4 tijd output Functie Waarde 0-255
18
-
Functie F09, Relais K-4 tijd output. Omschrijving
Relais K-4 tijd output
Card Master CM500
Basis waarde
Functie F10, Overbetaling acceptatie Functie Waarde Accept Retour
Functie F10, Overbetaling acceptatie. F10 kan worden ingesteld op accept of op retour. Omschrijving
Basis waarde
Overbetaling wordt geaccepteerd. Overbetaling wordt niet geaccepteerd, het ingeworpen bedrag wordt retour gegeven indien tussenkassa aanwezig is.
Functie F11, Automatische reset van het overbetalings bedrag Functie Waarde
Functie F11, Automatische reset van het overbetalings bedrag. Omschrijving
Basis waarde
Hierdoor kan een meervoudige verkoop plaats vinden. Bijvoorbeeld: er kan meer betaald worden dan de waarde van het produkt. Hierna blijft het resterende bedrag staan zodat er na bijbetaling wederom een 2e verkoop kan plaatsvinden. Overbetaling wordt geaccepteerd na een uitbetaling van munt(en)/product(en). Het restant wordt niet uitgekeerd maar gereset / gecleared. Wil de klant nog een aankoop doen dient deze klant opnieuw te betalen.
Hold
Clear
Functie F12, Retour toets teruggave Functie Waarde
Functie F12, Retour toets teruggave. Omschrijving
Basis waarde
Het restant na een verkoop zal op het display pas na de ingestelde tijd in F08 18 gereset worden. Het restant van een meervoudige verkoop wordt gereset bij het indrukken van de retour toets. Optioneel is een tussen kassa verkrijgbaar; deze biedt de mogelijkheid om het ingeworpen bedrag te retourneren.
Hold Clear Note:
Functie F13, Decimale punt positie Functie Waarde 0 / 0.00 0,00
Functie F13, Decimale punt positie. Omschrijving Waarde is of '0' of met 2 decimalen gescheiden door een punt. Waarde is altijd 2 decimalen gescheiden door een komma.
Basis waarde
Functie F14, Display helderheid Functie Waarde 0-7
Functie F14, Display helderheid. Stel de helderheid van de display in. Omschrijving Helderheid 0 is minimum, 7 is maximum.
Basis waarde
Functie F15, Tekst op display tijdens uitgifte Functie Waarde
Functie F15, Tekst op display tijdens uitgifte. Omschrijving
De tekst die op het display weergegeven word kan onafhankelijk en meertalig ingesteld worden. De keuze van Alfnumeriek de instelling is als volgt: Bill, Empt, Stuc, Piec, Out, Open, Leer, Leeg, Lauf, Funk, Fout, Fini, Fehl, Faut, Coin, Cart, Card, Busy, Ausg, Attn, 1111, ----, Uit, Aan, Off, On.
Basis waarde
Functie F16, Tekst op display tijdens rust Functie Waarde
Functie F16, Tekst op display tijdens rust. Omschrijving
Basis waarde
De tekst die op het display weergegeven word kan onafhankelijk en meertalig ingesteld worden. De keuze van de instelling is als Alfnumeriek volgt: Bill, Empt, Stuc, Piec, Out, Open, Leer, Leeg, Lauf, Funk, Fout, Fini, Fehl, Faut, Coin, Cart, Card, Busy, Ausg, Attn, 1111, ----, Uit, Aan, Off, On.
Version 2.5.1
-
19
Function Overview
Functie F17, Tekst op display tijdens foutieve betaling Functie Waarde
Functie F17, Tekst op display tijdens foutieve betaling. Omschrijving
Basis waarde
De tekst die op het display weergegeven word kan onafhankelijk en meertalig ingesteld worden. De keuze van de instelling is als Alfnumeriek volgt: Bill, Empt, Stuc, Piec, Out, Open, Leer, Leeg, Lauf, Funk, Fout, Fini, Fehl, Faut, Coin, Cart, Card, Busy, Ausg, Attn, 1111, ----, Uit, Aan, Off, On.
Functie F18, Tekst op display tijdens leeg Functie Waarde
Functie F18, Tekst op display tijdens leeg. Omschrijving
Basis waarde
De tekst die op het display weergegeven word kan onafhankelijk en meertalig ingesteld worden. De keuze van de instelling is als volgt: Alfnumeriek Bill, Empt, Stuc, Piec, Out, Open, Leer, Leeg, Lauf, Funk, Fout, Fini, Fehl, Faut, Coin, Cart, Card, Busy, Ausg, Attn, 1111, ----, Uit, Aan, Off, On.
Functie F19, Basiswaarde/rekenfactor Functie Waarde 0-255
Functie F19, Basiswaarde/rekenfactor. Voor het berekenen van diverse waarden/ bedragen maken wij gebruik van een basiswaarde/rekenfactor. De waarde die in deze functie staat ingegeven is de rekenfactor waarmee de waarden van o.a. de ingeworpen/ingevoerde munten en de uitgifte bepaald wordt. Omschrijving
Basis waarde
Basiswaarde/rekenfactor
Functie F20-F29, Waarde munt 1 - munt 10 Functie Waarde 0-255
Functie F20-F29, Waarde munt 1 - munt 10. Omschrijving
Basis waarde
Waarde munt
Functie F30, Muntwaarde hopper/dispenser 1 Functie Waarde 0-255
Functie F30, Muntwaarde hopper/dispenser 1. Omschrijving
Basis waarde
Muntwaarde hopper/dispenser 1.
Functie F31, Muntwaarde hopper/dispenser 2 Functie Waarde 0-9999
Functie F31, Muntwaarde hopper/dispenser 2. Omschrijving
Basis waarde
Muntwaarde hopper/dispenser 2.
Functie F32-F41, Inkomsten teller munt/biljet 1-10 Functie Waarde 0-9999
Functie F32-F41, Inkomsten teller munt/biljet 1-10. Omschrijving
Basis waarde
Inkomsten teller munt/biljet.
Functie F42, Uitgifte teller hopper/dispenser 1 Functie Waarde 0-9999
Functie F42, Uitgifte teller hopper/dispenser 1. Omschrijving
Basis waarde
Uitgifte teller hopper/dispenser 1.
Functie F43, Uitgifte teller hopper/dispenser 2 Functie Waarde 0-9999
20
-
Functie F43, Uitgifte teller hopper/dispenser 2. Omschrijving
Uitgifte teller hopper/dispenser 2.
Card Master CM500
Basis waarde
Surplus payment' , F 10, F 11 and F 12 F 10 can be programmed accept or return, which have the following functions: § Accept, surplus payment is accepted § Return, surplus payment is not accepted, or the inserted amount F 11 can be programmed Hold or Clear, which have the following functions: § Clear, surplus payment is accepted after returning the coin(s)/product(s). The remaining amount is not returned but reset. If the client wants to buy again, he has to insert money again § Hold, this permits multiple sales. Example: an amount of money surpassing the price of the product can be introduced, the remaining amount is maintained and a second product can be bought after inserting more money if necessary F 12 can be programmed Hold or Clear, which have the following functions: § Clear, the remaining amount of multiple sales is reset by pressing the return button § Hold, the remaining amount after a sale is shown in the display and reset after a period of time programmed in F 08 Optional: intermediate check-out, offers the possibility of returning the inserted amount. Basic value/accounting factor, F 19 To book the different values/amounts a basic value/accounting factor is used. The value introduced in this function is the accounting factor by which the values of the inserted coins and return values are defined. Text in display during, F 15 to F 18 The displayed text can be programmed independently and in various languages. The following programming choices can be selected: Bill, Empt, Stuc, Piec, Out, Open, Leer, Leeg, Lauf, Funk, Fout, Fini, Fehl, Faut, Coin, Cart, Card, Busy, Ausg, Attn, 1111, ----, Uit, Aan, Off, On.
Timer input De timer input-aansluiting is bedoeld voor verkoopautomaten waar meerdere prijzen noodzakelijk zijn. Door het aansturen van een timer-input ontstaat er de verkoopprijs die in F01 18 , F02 18 of F03 18 ingegeven staat. Bij geen aansturing wordt automatisch de prijs die ingegeven staat in F00 18 berekend. De ingangen van de timer zijn opto-coupler ingangen, deze ingangen zijn bestendig tegen spanningen tussen de 5V en de 30V aansluitbaar op de VMS-1. De aansluiting bestaat uit een 4polige connector, deze zit op het main board bevestigd. Pin 4 is de pin die het dichtst bij de aansluit-kroonsteen zit! Pin 1 en pin 2 is input 2 Pin 3 en pin 4 is input 1 Functie F00 / F04 F01 / F05 F02 / F06 F03 / F07
input 1 Off Off On On
Input 2 Off On Off On
Pin 1 Pin 2 Pin 3 Pin 4 Prijs 1a / 2a + 1b / 2b + 1c / 2c + + 1d / 2d
Version 2.5.1
-
21
Programming example
IX
Part
Programming example
Programming Example Example 1 A dispenser with 6 coin types admittance (€ 0,05 to € 2.00), without coin return, with the possibility of an intermediate check-out to return the money when too few coins have been inserted. Function Value 200, the selling price for a ticket is € 10,00 (the programmed value multiplied with the value F00 programmed in F 19) F08 1, after surplus payment, the client has one minute to introduce more coins to buy a second ticket F10 "acc", surplus payment is accepted F11 "hold", the remaining amount is maintained in case too many coins are introduced "hold", if too few coins are inserted, the inserted amount is returned by pressing the return button, F12 this is only possible in machines with intermediate check-out (option) F19 5, the accounting factor defines coin value and sales value F20 1, coin value 1 x 5 = € 0,05 F21 2, coin value 2 x 5 = € 0,10 F22 4, coin value 4 x 5 = € 0,20 F23 10, coin value 10 x 5 = € 0,50 F24 20, coin value 20 x 5 = € 1,00 F25 40, coin value 40 x 5 = € 2,00
Example 2 The change machine accepts 4 coin types (€ 0,20 to € 2,00) and returns 2 coin types (€ 0,10 and € 0,50). Admittance € 0,20, return 2 x € 0,10 Admittance € 0,50, return 5 x € 0,10 Admittance € 1,00, return 5 x € 0,10 and 1 x € 0,50 Admittance € 2,00, return 5 x € 0,10 and 3 x € 0,50 Functie F00 F01 F02 F03 F04 F05 F06 F07 F10 F11 F15 F16 F16 F18 F19 - F30
24
-
Waarde 2, number of coin(s) hopper 1 has to return accepting coin 1 5, number of coin(s) hopper 1 has to return accepting coin 2 5, number of coin(s) hopper 1 has to return accepting coin 3 5, number of coin(s) hopper 1 has to return accepting coin 4 0, number of coin(s) hopper 2 has to return accepting coin 1 0, number of coin(s) hopper 2 has to return accepting coin 2 1, number of coin(s) hopper 2 has to return accepting coin 3 3, number of coin(s) hopper 2 has to return accepting coin 4 "acc", surplus payment is accepted "hold", surplus payment is automatically reset "coin", text in display during return "coin", text in display during inactive period "error", text in display in case of wrong payment "empty", text in display if one of the hopper is empty Function F 19 to F 30 have to be in position 1 to confirm the registration/admittance of the coins.
Card Master CM500
Ticket Dispencers
X
Part
Ticket Dispencers
The ticket dispensers The ticket dispenser(s) is/are the ticket unit (s) of the machine, this/these unit (s) have to be filled with tickets to guarantee a correct functioning of the machine. Shuffle the ticket before introducing them into the dispenser to avoid their sticking to one another, and put the weight onto the ticket stack. The 'empty' signal is activated when the last ticket is given out.
26
-
Card Master CM500
Optional
XI
Part
Optional
Optional
28
-
1.
A programming device, to simplify the operation of the function-menu.
2.
A reset and counting device, to read the counters only and to reset the daily counters.
3.
PC support software, on-line connection, to run various sales machines.
Card Master CM500
General technical data
XII
Part
General technical data
General technical data Power Power Usage Fuses
230 VAC About. 150 VA (depending on the input / output unit) 2 x 200mAT
Housing Material Dimensions H x W x D Configuration Locks Optional
Standard 2 mm. steel casing, including 15 mm. door frame 600 x 450 (550) x 320 mm (depending on the configuration) Two-colour polish (RAL colours) Central lock · Pillar mounted · 3-pont security lock
User Interface · Function/Enter key · Count Down key Keys (Integrated on the VMS-1 · Count Up key main board) · Empty Hopper/Dispenser key · Reset key 4-way LED display Weergave
Weight Weight
30
-
Card Master CM500
About 35 kg. (depending on the configuration)
Troubleshooting
XIII
Part
Troubleshooting
Troubleshooting Message in the external display: Display 00,00 Empty
Description Amount to pay Hopper/dispenser is empty, fill hopper/dispenser with the corresponding coins/products Wrong payment, control and reset the change system
Error Busy / paying/returning Occupied
As the programmed texts can be changed, the text in the display must not necessarily coincide with that described before (see function 15 to 18). Error Codes Error Description Code
32
-
0
Hardware error in the microcomputer
1
EEPROM hardware error
2
Hardware error in the I / O register
3
EEPROM data error
4
Configuration data error
5
Logical error in the configuration
6
EEPROM writing error
7
Input error in the I / O register
8
Coin system error
9
Register calibration error
A
EEPROM reading error
Card Master CM500
Action Error impossible to be rectified by the user, it is advisable to call on a specialist to test the electronic components. Error impossible to be rectified by the user, it is advisable to call on a specialist to test the electronic components. Possibly an error in the function-settings, change at least one of the functions; then check the machine. If it works correctly, you can set the changed function back in the setting you want. Possibly an error in the function-settings, change at least one of the functions; then check the machine. If it works correctly, you can set the changed function back in the setting you want. Error impossible to be rectified by the user, it is advisable to call on a specialist to test the electronic components. Error impossible to be rectified by the user, it is advisable to call on a specialist to test the electronic components. Error impossible to be rectified by the user, it is advisable to call on a specialist to test the electronic components. Error impossible to be rectified by the user, it is advisable to call on a specialist to test the electronic components. Test the coin system with coins inserted, reset the change system by means of the reset button or (de)activate the change system. Test the function-menu, it is impossible to programme the chosen function, or the chosen function is not active in this model. Error impossible to be rectified by the user, it is advisable to call on a specialist to test the electronic components.
VMS-1 Overview
XIV
Part
VMS-1 Overview
VMS-1 Overview 1. 230VAC connection 2. 200Ma-T fuse 3. Reset button 4. Serial input connection 5. Output hopper / dispenser 6. Hopper / dispenser button 7. Escrow connection 8. Input hopper / dispenser 9. Up button 10.Function jumper 11.Down button 12.Function button 13.Coin acceptor connection 14.Display connection 15.Timer connection 16.5 / 12 / 24V output
34
-
Card Master CM500
Version 2.5.1
-
35
