8 1 2 3
8
9
4 5 6
10 11
7
12
TECHNICAL MANUAL PANDUAN TEKNIS
DISMANTLING PB T400 CARA MEMBONGKAR PB T400 A. Make sure the cord has been unplugged from the electrical outlet. A. Pastikan kabel konektor listrik telah dicabut.
B. Remove the drip tray and water container for easier process. B. Lepaskan drip tray & water container agar mempermudah proses.
C. Remove the rotary switch by using two “-” screwdrivers at each respective hole. (1) C. Lepaskan rotary switch dengan menggunakan dua buah obeng minus. (1) D. Loose two screws located just beneath it. D. Lepaskan dua baut yang berada di bawah rotary switch.
2
E. Remove the top cover cone. (4) E. Angkat top cover cone. (4)
F. Loose five screws located at the back part of the machine, two screws at the bottom part and three screws just beneath the bottom cover. F. Lepaskan 5 baut yang berada pada sisi belakang mesin, 2 baut di bagian bawah dan 3 baut di dalam cover mesin bagian bawah.
G. Remove the back side casing and the side one. G. Lepaskan casing bagian belakang dan samping.
H. Unplug the electrical switch, mark it for easier installation. H. Lepaskan switch kabel konektor dan berikan tanda untuk mempermudah pemasangan.
3
TROUBLESHOOTING PB T400 DIAGNOSA PB T400 1. Clogged (the water doesn’t flow through the coffee mouth) 1. Mampet / Tersumbat (air tidak keluar) Alternative 1 Cara Pertama
4
A. Lift the pod brewer handle (48).
B. Loose the PB T400 manifold cone (37) just above the porta filter.
A. Angkat tuas pod brewer (48).
B. Lepaskan manifold cone (37) PB T400 yang terletak di atas porta filter.
C. Turn on the switch to do simple flushing for taking out the mineral sediment.
D. Screw back the PB T400 manifold cone (37) after finished flushing the machine.
C. Hidupkan tombol power untuk melakukan pembilasan guna menghilangkan endapan mineral.
D. Kencangkan kembali manifold cone (37) PB T400 setelah selesai melakukan pembilasan.
If the previous method doesn’t work. Jika cara sebelumnya tidak bekerja. Alternative 2 Cara Kedua
A. Do the dismantling procedure above.
B. Open the switch shaft unit (6) using 26” wrench.
A. Lakukan langkah pembongkaran mesin seperti di atas.
B. Buka switch shaft unit (6) menggunakan kunci 26”
C. Loose four screws located at the back.
D. Remove three cables (red, yellow, blue) and mark it.
C. Lepaskan empat baut yang terletak dibelakang.
D. Lepaskan tiga kabel yang terpasang berwarna merah, kuning, biru dan beri tanda.
5
E. Remove one screw at the WK-400 collector bottom (44), remove the coffee mouth (45) and the collector bottom (44) as well. E. Lepaskan baut yang terdapat pada collector bottom (44), lepaskan coffee mouth (45) dan juga collector bottomnya (44)
8
F. Loose four screws at the back of the thermo block case and remove the case. F. Lepaskan empat baut yang terdapat dibelakang casing thermo block dan lepaskan casingnya.
G. Loose two screws on each side of the handle (48), release the lock at the lower side of the handle and remove the handle (48).
H. Remove the unscrew manifold housing (31) at the bottom of the thermo block by turning it counter-clockwise.
G. Lepaskan dua baut di setiap sisi handle (48), lepaskan ring pengunci yang terletak dibawah baut handle (48) tersebut dan lepaskan handle (48).
H. Lepaskan manifold housing (31) yang terletak dibagian bawah thermo block dengan cara memutar berlawanan arah jarum jam.
I. Remove the bottom bracket plate (40). I. Lepaskan bottom bracket plate (40).
J. Look at the middle of the thermo block, there is a rod of water (16). Take it out by pushing it upward with the help of “L” key driver J. Perhatikan di bagian tengah thermo block, terdapat rod of water (16). Keluarkan dengan cara menekannya keatas dengan menggunakan alat bantu kunci “L”.
K. Take out the rod (16) and clean it.
L. Assemble the machine.
K. Keluarkan rod of water (16) dan bersihkan.
L. Rakit kembali mesin
M. Test the machine. M. Jalankan mesin
9
TROUBLESHOOTING PB T400 DIAGNOSA PB T400 2. Water doesn’t run (pump doesn’t work) 2. Air tidak mengalir (pompa tidak bekerja)
A. Release the cable connected to the pump, mark it for easier installation. A. Lepaskan kabel yang terkoneksi ke pompa, berikan tanda untuk memudahkan pemasangan kembali.
10
B. Cut the cable ties that tied the water silicon hose. B. Gunting kabel ties yang mengikat selang air.
C. Loose two screws at the pump fixed plates (70).
D. Loose the pump tube directly (25) using 12” wrench.
C. Lepaskan dua baut yang terdapat pada pump fixed plates (70).
D. Lepaskan pump tube directly (25) dengan menggunakan kunci 25”.
E. Lift the pump (pull upward), release the pump shock spring (68) and the silicone hose attached to it .
F. Replace with the new pump. F. Ganti dengan pompa baru
E. Angkat pompa, lepaskan pump spring shock (68) dan selang silikon yang tersambung.
G. Assemble the machine and do the testing. G. Rakit kembali dan lakukan pengetesan.
11