Proxima ISDN Lite External
Installatiehandleiding Manuel d’installation Installation Guide
Proxima ISDN Lite
Installatiehandleiding
Installatiehandleiding Proxima ISDN Lite Deze handleiding staat onder de bescherming van de wet van het intellectuele eigendom. Het is dus verboden haar te copiëren, op te nemen, te vertalen of op enige andere wijze te reproduceren, zelfs gedeeltelijk. De fabrikant behoudt zich het recht voor zonder voorafgaandelijke mededeling wijzigingen aan te brengen of het product aan de technische ontwikkelingen aan te passen. Alle in deze handleiding vermelde merken zijn gedeponeerde handelsmerken. Proxima ISDN Lite. Installatiehandleiding © BAUSCH DATACOM NV/SA November 1999.
Manuel d’installation Proxima ISDN Lite Ce manuel est protégé par la loi sur la propriété littéraire. Il ne peut donc pas être photocopié, enregistré, traduit ou reproduit de quelque façon que ce soit, même partiellement. Le fabricant se réserve le droit, sans préavis, de procéder à des modifications, ou de développer le produit en fonction des progrès techniques. Toutes les marques citées sont des marques déposées. Proxima ISDN Lite. Manuel d’installation BAUSCH DATACOM NV/SA Novembre 1999.
Installation Guide Proxima ISDN Lite This manual is under protection of the law of intellectu al property. Therefore it is illegal to copy, translate or reproduce this manual, even partially. The manufacturer reserves the right to change or adapt the products without preliminary notice. All brands mentioned in this manual are trademarks. Proxima ISDN Lite Installation Guide © BAUSCH DATACOM NV/SA November 1999.
30/11/1999
2
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
INHOUDSOPGAVE
6
TABLE DES MATIERES
26
TABLE OF CONTENTS
47
30/11/1999
3
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
Installatiehandleiding
PROXIMA ISDN LITE
30/11/1999
4
Bausch Datacom
Proxima ISDN Lite
30/11/1999
Installatiehandleiding
5
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
INHOUDSOPGAVE
INLEIDING
8
1. AANSLUITEN VAN DE MODEM
9
2. INSTALLATIE VAN DE DRIVERS
10
2.1. PLUG EN PLAY INSTALLATIE IN WINDOWS 98 2.2. PLUG EN PLAY INSTALLATIE IN WINDOWS 95 2.3. HANDMATIGE INSTALLATIE IN WINDOWS NT
10 13 15
3. INSTALLATIE VAN DE CONFIGURATIESOFTWARE
17
4. CONFIGURATIE VAN DE PROXIMA ISDN LITE
20
30/11/1999
6
Bausch Datacom
Proxima ISDN Lite
30/11/1999
Installatiehandleiding
7
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
Inleiding Proficiat met de aanschaf van de Proxima ISDN Lite. Indien u een supersnelle Internet-verbinding wenst op te zetten via ISDN, dan zal dit toestel u aangenaam verrassen. Dankzij de meegeleverde communicatiesoftware (RVS-Com Lite en/of BVRP) kan u zonder problemen Internet-connecties opzetten, faxen zenden en ontvangen en het toestel als een antwoordapparaat gebruiken. De gebruiksvriendelijkheid van deze ISDN-adapter wordt weerspiegeld in de klare, drietalige installatiehandleiding (Nl/F/E) en de meegeleverde configuratiesoftware. Hiermee kan u bijvoorbeeld het B-kanaal protocol heel eenvoudig instellen evenals de MSN-nummers (meervoudige abonneenummers). Door deze eenvoud in gebruik biedt de Bausch Proxima ISDN Lite de allerbeste verhouding prijs/kwaliteit in de markt. In deze installatiehandleiding wordt beschreven hoe de Bausch Proxima ISDN Lite dient aangesloten te worden aan uw PC en hoe u de drivers moet installeren. Bovendien wordt het configuratieprogramma toegelicht. De handleiding bevat de volgende hoofdstukken: 1. Aansluiten van de Bausch Proxima ISDN Lite. 2. Installatie van de drivers. 2.1. Plug & Play installatie in Windows 98. 2.2. Plug & Play installatie in Windows 95. 2.3. Handmatige installatie in Windows NT. 3. Installatie van de configuratiesoftware. 4. Configuratie van de Proxima ISDN Lite. Uitgebreide informatie over en een beschrijving van alle commando’s van de Bausch Proxima ISDN Lite kan u vinden in de gebruikershandleiding. De • • • • • • • •
Bausch Proxima ISDN Lite wordt geleverd met de volgende accessoires: ISDN-aansluitkabel (RJ-45). Seriële kabel (RS-232). Netspanningsadapter. RVS-Com Lite en/of BVRP-communicatiesoftware op CD-ROM. Diskette met drivers en configuratiesoftware. Introductiepakket(ten) met gratis toegang tot het Internet. Gebruikershandleiding. Deze installatiehandleiding.
Minimale vereisten: • Hardware: - CPU: 486 of hoger - RAM: 16 MB of meer - Telecom vereisten: 1 ISDN BRI-lijn (S/T interface) • Software: - Platform: MS Windows 95, 98 and NT 4.0 30/11/1999
8
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
1. Aansluiten van de Bausch Proxima ISDN Lite. In deze paragraaf wordt uitgelegd hoe de Bausch Proxima ISDN Lite dient aangesloten te worden.
Beschrijving van de LED’s van links naar rechts TD RD CD OH AA HS DTR MR PWR
Transmitted data Received data Carrier detect Channel B1 in use Ring indicator Channel B2 in use Data terminal ready Clear to send Power
Verzonden data Ontvangen data TA is verbonden Kanaal B1 in gebruik Inkomende oproep Kanaal B2 in gebruik Data terminal ready Clear to send TA is geactiveerd
Werkwijze: 1. Neem de ISDN-kabel en klik de (kleine) RJ-11connector in de SO-Bus aansluiting achteraan de Bausch Proxima ISDN Lite. Klik daarna de (grote) RJ45 connector in de TWIN/BRA van Belgacom of in de voorziene wandcontactdoos. 2. Verbind de seriële poort (RS-232) achteraan de Bausch Proxima ISDN Lite met die van de computer via de meegeleverde seriële kabel. 3. Sluit de netspanningsadapter van de Bausch Proxima ISDN Lite aan (Power = PWR, achteraan). 4. Zet de computer aan. De Bausch Proxima ISDN Lite is nu aangesloten. 30/11/1999
9
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
2. Installatie van de drivers. Voordat u kan werken met de Proxima ISDN Lite moeten de drivers geï nstalleerd worden. Indien u gebruik maakt van Windows 95 of 98 zal de installatie automatisch verlopen via de Plug & Play functionaliteit van Windows. Als u met Windows NT werkt, moet de installatie handmatig gebeuren.
2.1 Plug & Play Installatie in Windows 98. Nadat u de computer heeft aangezet, geeft Windows 98 aan dat er nieuwe hardware is gevonden. De installatie gaat als volgt (we tonen de Engelstalige schermen van Windows 98): Nadat Windows 98 de Bausch Proxima ISDN Lite heeft gevonden, verschijnt het volgende scherm: Klik op ‘Next’ (Volgende).
Klik op ‘Next’ (Volgende).
30/11/1999
10
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
Selecteer de plaats (‘Floppy disk drives’) waar Windows de nodige drivers kan vinden. Plaats de meegeleverde driverdiskette in het diskettestation en klik op ‘Next’ (Volgende).
Windows bevestigt de aanwezigheid van de correcte drivers. Klik op ‘Next’ (Volgende).
Alle benodigde bestanden worden nu naar de computer getransfereerd.
30/11/1999
11
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
De verschillende ‘modems’ (één ‘modem’ per mogelijk ISDN B-kanaal protocol) worden nu automatisch geï nstalleerd. Proxima ISDN Lite V.120 Proxima ISDN Lite PPP Proxima ISDN Lite V.110 Proxima ISDN Lite ML-V.120 Proxima ISDN Lite ML-PPP
V.120 protocol – 64 Kbps PPP protocol – 64 Kbps V.110 protocol multilink V.120 protocol – 128 Kbps multilink PPP protocol – 128 Kbps
Windows suggereert dat men voor elk protocol een aparte ‘modem’ nodig heeft. Het is echter zo dat één ‘modem’ (in dit geval, de Bausch Proxima ISDN Lite) al deze protocollen aan kan. Op het einde van de installatie moet de computer opnieuw opgestart worden. Verwijder de driver- diskette uit het diskettestation en klik op ‘Reboot’.
Als dit allemaal gelukt is, kunt u verdergaan met hoofdstuk 3, ‘Installatie van de configuratiesoftware’. Zo niet, dan kunt u de Bausch Proxima ISDN Lite handmatig installeren, zoals beschreven in hoofdstuk 2.3, ‘Handmatige installatie in Windows NT’.
30/11/1999
12
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
2.2 Plug & Play installatie in Windows 95. Nadat u de computer heeft aangezet, geeft Windows 95 aan dat er nieuwe hardware is gevonden. De installatie gaat als volgt (we tonen de Engelstalige schermen van Windows 95). Nadat Windows 95 de Bausch Proxima ISDN Lite heeft gevonden, verschijnt het volgende scherm: klik op ‘Next’ (Volgende).
Plaats de meegeleverde driverdiskette in het diskettestation en klik op ‘Finish’ (Beëindigen).
Alle benodigde bestanden worden nu naar de computer getransfereerd.
30/11/1999
13
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
Opmerking: In sommige versies van Windows 95 wordt de automatische installatieprocedure onderbroken en moet men ‘handmatig’ de naam van het diskettestation ingeven. Geef dan gewoon A:\ in. De installatie verloopt daarna verder zoals het moet. De verschillende ‘modems’ (één ‘modem’ per mogelijk ISDN B-kanaal protocol) worden nu automatisch geï nstalleerd. Proxima ISDN Lite V.120 Proxima ISDN Lite PPP Proxima ISDN Lite V.110 Proxima ISDN Lite ML-V.120 Proxima ISDN Lite ML-PPP
V.120 protocol – 64 Kbps PPP protocol – 64 Kbps V.110 protocol multilink V.120 protocol –128 Kbps multilink PPP protocol – 128 Kbps
Windows suggereert dat men voor elk protocol een aparte ‘modem’ nodig heeft. Het is echter zo dat één ‘modem’ (in dit geval, de Bausch Proxima ISDN Lite) al deze protocollen aan kan. Op het einde van de installatie moet de computer opnieuw opgestart worden. Verwijder de driver- diskette uit het diskettestation en klik op ‘Reboot’.
Opmerking: In sommige versies van Windows 95 wordt het bovenstaande scherm niet gegeven. Als deze melding na de installatie niet gegeven wordt, moet Windows 95 manueel herstart worden. Ga hiervoor naar Start, Afsluiten of ‘Shutdown’ en selecteer dan De Computer opnieuw opstarten of ‘Restart the computer’. Als dit allemaal gelukt is, kunt u verdergaan met hoofdstuk 3, ‘Installatie van de configuratiesoftware’. Zo niet, dan kunt u de Bausch Proxima ISDN Lite handmatig installeren, zoals beschreven in hoofdstuk 2.3, ‘Handmatige installatie in Windows NT’.
30/11/1999
14
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
2.3 Handmatige installatie in Windows NT. Indien uw systeem geen nieuw apparaat detecteert of al aan staat, moet u de volgende stappen ondernemen. Klik op de knop Start van de taakbalk, selecteer Instellingen en klik op Configuratiescherm (‘Start’, ‘Settings’, ‘Control Panel’). Het Configuratiescherm verschijnt. Dubbelklik hier op Modems. Aangezien Windows geen specifieke ISDN-apparaten kent, wordt een Terminal Adapter zoals de Bausch Proxima ISDN Lite als een ‘modem’ aangestuurd. Op het scherm verschijnt nu een venster Modems (‘Modems Properties’, ‘General’). Klik op de knop Toevoegen (‘Add’). Klik op het lege vakje voor Modem niet detecteren; zelf selecteren in een lijst (‘Don’t detect my modem; I will select it from a list’). Er komt een V in het vakje. Klik op Volgende (‘Next’). Soms moet hier even gewacht worden omdat Windows een database van de drivers samenstelt.
30/11/1999
15
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
In het volgende venster staan verschillende types van modems. Er moet echter een model vanaf de meegeleverde driverdiskette geï nstalleerd worden. Klik daarom op Diskette (‘Have Disk’).
Plaats de meegeleverde diskette in het diskettestation. Selecteer de juiste drive en klik op OK. Nu verschijnt het volgende venster:
Selecteer het model dat geï nstalleerd moet worden, bijvoorbeeld: • Bausch Proxima ISDN Lite PPP voor communicatie met een ISP (Internet Service Provider). • Bausch Proxima ISDN Lite V.120 voor communicatie met een BBS (Bulletin Board System). Klik op Volgende (‘Next’). Nu verschijnt er een venster waarin de seriële poort, waaraan de Bausch Proxima ISDN Lite is aangesloten, geselecteerd moet worden. Over het algemeen is dit COM2. Selecteer de poort en klik vervolgens op Volgende (‘Next’). 30/11/1999
16
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
Nu verschijnt het laatste venster met de melding Uw modem is geïnstalleerd (‘Your modem has been set up successfully’). Klik nu op Voltooien (‘Finish’).
Als u meerdere protocollen wenst te installeren, kunt u dat doen door de laatste stappen te herhalen. Hierna is de installatieprocedure voltooid. Opmerking: Windows suggereert dat men voor elk protocol een aparte ‘modem’ nodig heeft. Het is echter zo dat één ‘modem’ (in dit geval, de Bausch Proxima ISDN Lite) al deze protocollen aan kan.
3. Installatie van de configuratiesoftware. Na de Plug & Play installatie van de drivers in Windows 95/98 (hoofdstuk 2.1 en 2.2) is de installatie van de configuratiesoftware automatisch begonnen en wordt het openingsscherm, zoals afgebeeld bovenaan de volgende pagina, getoond. Indien u de installatie handmatig (hoofdstuk 2.3) aan het doen bent in Windows NT of omdat de installatie in Windows 95/98 problematisch verliep, kunt u de configuratiesoftware installeren door achtereenvolgens Start, Uitvoeren (‘Run’) te selecteren en dan A:SETUP in te tikken. Vervolgens klikt u op OK. Hierna verschijnt het openingsscherm, zoals afgebeeld bovenaan de volgende pagina. Klik nu op Volgende (‘Next’). Opmerking: Vooraleer de configuratie te starten, is het aangeraden eerst alle programma’s onder Windows te sluiten. In dat geval klikt u op ‘Cancel’. Sluit daarna alle Windows programma’s af en keer terug naar de installatie van de configuratiesoftware (zie hierboven: installeren van de configuratiesoftware na handmatige installatie van de drivers).
30/11/1999
17
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
In de volgende schermen kunt u de map en programmagroep aanpassen waar de configuratiebestanden komen te staan. Voor de standaardmap en -groep klikt u in beide schermen op ‘Next’.
30/11/1999
18
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
Klik nu op ‘Finish’ om de Setup af te sluiten en de configuratiesoftware te starten. Zorg ervoor dat de Bausch Proxima ISDN Lite aangesloten is en dat deze aan staat.
30/11/1999
19
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
4. Configuratie van de Proxima ISDN Lite. Het configuratieprogramma zoekt nu naar de Proxima ISDN Lite. Het versienummer kan verschillen van het hier getoonde. Klik op ‘Next’ om verder te gaan met de configuratie.
Het instellen van MSN-nummers. Wanneer u een ISDN-aansluiting bestelt, is het mogelijk om meer dan één en maximaal 8 telefoonnummers aan te vragen bij de telefoonmaatschappij. Bij Belgacom bijvoorbeeld krijgt men bij de aanvraag van een standaard BRAaansluiting 1 hoofdnummer. Bijkomende nummers dienen aangevraagd en betaald te worden. Bij een TWIN-aansluiting geeft Belgacom bijvoorbeeld twee nummers en dienen de bijkomende nummers apart te worden aangevraagd en betaald. Een dergelijke dienstverlening wordt ook wel MSN genoemd (‘Multiple Subscriber Numbers’ of in het Nederlands ‘Meervoudige Abonnee Nummers’). De Bausch Proxima ISDN Lite kan als dusdanig worden geconfigureerd dat een telefoonnummer gekoppeld wordt aan een protocol. Wordt dit nummer gebeld, dan zal de Bausch Proxima ISDN Lite een verbinding volgens het ingestelde protocol opbouwen. In het scherm zoals op de volgende pagina aangegeven, kunnen alle MSNnummers die horen bij de ISDN-2-aansluiting ingevuld worden.
30/11/1999
20
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
Klik op ‘Next’ om verder te gaan. In onderstaand scherm dient u in te geven welk MSN-nummer u wenst te koppelen aan een welbepaald B-kanaal protocol. Als gekozen wordt voor de optie ‘all numbers’ zal de Proxima ISDN Lite elke binnenkomende communicatie-aanvraag aanvaarden. Wordt gekozen voor de optie ‘none’ dan reageert de Proxima Lite ISDN niet op een binnenkomende communicatie aanvraag.
Let op: de applicatiesoftware zoals RVS-Com Lite, BVRP of DUN/RAS moet geactiveerd zijn om een binnenkomende call te kunnen beantwoorden. Klik op ‘Next’ voor het volgende scherm.
30/11/1999
21
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
Bij ‘Connected Line Identification Presentation’ kan u het uitbellende nummer ingeven. Dit nummer wordt zichtbaar bij de gebelde partij nog voordat het gesprek wordt beantwoord. Als gekozen wordt voor ‘main number’, wordt het hoofdnummer ingesteld. CLIP = ‘incoming number’, ingegeven door degene die naar u belt. COLP = ‘outgoing number’ dat u zelf op deze plaats in de configuratiesoftware kan ingeven. ‘CLIP’ en ‘COLP’ zijn dus complementaire begrippen. Het door u ingegeven nummer (‘COLP’) wordt een ‘CLIP’ voor degene die door u wordt opgebeld. Met de optie ‘Default data protocol’ kan u instellen welk B-kanaal protocol u als standaardinstelling verkiest wanneer de Proxima ISDN Lite wordt aangezet of gereset. Klik op ‘Next’ voor het volgende scherm.
Door op ‘Finish’ te klikken wordt de ingestelde configuratie bewaard in de Bausch 30/11/1999
22
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
Proxima ISDN Lite.
Hiermee is uw Proxima ISDN Lite ingesteld voor gebruik. Klik op ‘Exit’ om het configuratieprogramma te verlaten.
30/11/1999
23
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
Manuel d’installation
PROXIMA ISDN LITE
30/11/1999
24
Bausch Datacom
Proxima ISDN Lite
30/11/1999
Installatiehandleiding
25
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
TABLE DES MATIERES PREFACE
28
1. LA MISE EN SERVICE DU PROXIMA ISDN LITE
30
2. L’INSTALLATION DES PILOTES
31
2.1. INSTALLATION PLUG & PLAY SOUS WINDOWS 98 2.2. INSTALLATION PLUG & PLAY SOUS WINDOWS 95 2.3. INSTALLATION MANUELLES SOUS WINDOWS NT
31 34 36
3. L’INSTALLATION DE L’UTILITAIRE DE CONFIGURATION ‘CONFIGURATION TOOL‘ SOUS 95/98/NT 39 4. CONFIGURATION DU PROXIMA ISDN LITE
30/11/1999
26
41
Bausch Datacom
Proxima ISDN Lite
30/11/1999
Installatiehandleiding
27
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
Préface Félicitations. Vous avez choisi le boîtier Proxima ISDN Lite de Bausch Datacom pour découvrir le monde de la communication de données avec votre ordinateur ou votre terminal. Si vous désirez vous connecter à Internet à travers une ligne numérique, la solution Proxima ISDN Lite vous donnera satisfaction. Ce boîtier externe est livré avec un manuel d’installation trilingue et tous les logiciels nécessaires pour configurer et pour communiquer, permettant ainsi des applications comme l’accès à Internet, le Minitel, l’envoi et la réception de Fax G3 et le répondeur intégré. Sa simplicité d’emploi en fait un produit très efficace de communication. Par exemple, l’utilitaire de configuration unique vous permet de changer le protocol par défaut du canal B et de changer les numéraux MSN. Le boîtier se positionne sur le marché avec un excellent rapport qualité/prix. Ce manuel d’installation décrit la façon de raccordement de votre boîtier Proxima ISDN Lite à votre PC et comment il faut procéder à l’installation des pilotes. En plus l’utilitaire ‘Configuration Tool’ vous sera expliqué. Normalement ce manuel d’installation vous permettra d’installer, de configurer et de travailler avec votre adaptateur numéris ISDN. Bonne chance et bonne communication. Ce manuel d’installation comprend: 1.
La mise en service du Bausch Proxima ISDN Lite.
2.
L’installation des pilotes. 2.1. 2.2. 2.3.
Installation Plug & Play sous Windows 98. Installation Plug & Play sous Windows 95. Installation manuelle des pilotes sous Windows NT.
3.
L’installation de l’utilitaire de configuration ‘Configuration Tool’ sous Windows 95/98/NT.
4.
Configuration du Proxima ISDN Lite.
Pour des informations détaillées et une description de toutes les commandes du Proxima ISDN Lite, veuillez consulter le manuel de l’utilisateur.
Composition du produit et équipements nécessaires: 30/11/1999
28
Bausch Datacom
Proxima ISDN Lite
• • • • • • • • •
Installatiehandleiding
Le boîtier Proxima ISDN Lite. Le manuel d’installation en français, néerlandais et anglais. Le manuel de l’utilisateur en français, néerlandais et anglais. Le logiciel de communication multifonctionnel RVS-Com Lite et/ou BVRP (Fax G3, répondeur intégré, Minitel, Internet…). La disquette contenant les pilotes (Win95, Win 98, WinNT4.0) et le logiciel de configuration. Le câble de raccordement ISDN (RJ-45). Le câble série (RS-232). L’alimentation L’accès gratuit à Internet.
Configuration minimale: •
•
Hardware: - CPU: 486 ou supérieur - RAM: 16 MB ou supérieur - Téléphonie: connexion ISDN BRI S0/RJ-45 Software: - Plate-forme: MS Windows 95, 98 and NT 4.0
30/11/1999
29
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
1. La mise en service du Bausch Proxima ISDN Lite Dans ce chapitre nous vous guiderons pendant le raccordement et la mise en service du Bausch Proxima ISDN Lite.
Votre modem possède des indicateurs LED sur la face avant qui affichent l’état du modem. LED TD RD CD OH AA HS DTR MR PWR
Fonction Envoi de données Réception de données Connexion établie Canal B1 en communication Attente d’appel activée Canal B2 en communication Terminal connecté: signal DTR actif Adaptateur prêt à fonctionner L’adaptateur est sous tension
Transmitted data Received data Carrier detect Channel B1 in use Ring indicator Channel B2 in use Data terminal ready Clear to send Power
Raccordement du Bausch Proxima ISDN Lite. 1. Eteignez votre ordinateur. 2. Prenez le câble ISDN et introduisez le petit connecteur RJ-11 dans le connecteur marqué ‘SO-Bus’ au dos du Bausch Proxima ISDN Lite jusqu’au clic. Branchez l’autre extrémité du câble ISDN (RJ-45) sur le connecteur murale ISDN S0 (NT1). 3. Branchez l’extrémité mâle (25 broches) du câble série dans le connecteur marqué ‘RS232’ au dos du boîtier. Branchez l’autre extrémité du câble série sur le port série de votre ordinateur. 4. Mettez le Bausch Proxima ISDN Lite sous tension (PWR=Power, au dos du boîtier). 5. Allumez votre ordinateur. Votre boîtier Bausch Proxima ISDN Lite est maintenant raccordé. 30/11/1999
30
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
2. L’installation des pilotes. Avant de pouvoir utiliser le Bausch Proxima ISDN Lite, vous devez installer les pilotes. Si vous utilisez Microsoft Windows 95 of 98, l'installation se fait automatiquement à l'aide de la fonction Plug & Play. Si vous utilisez Windows NT, vous devez les installer manuellement. Pour l'installation manuelle des pilotes sous Windows NT, reportez-vous au chapitre 2.3.
2.1 Installation Plug & Play sous Windows 98. Après le démarrage de l'ordinateur, Windows 98 vous avertit qu'il a détecté un nouveau périphérique. Les captures d'écran suivantes proviennent de Windows 98, version anglaise. L'installation se déroule comme suit: Cliquez sur Suivant (‘Next’).
Cliquez sur Suivant (‘Next’). Sélectionnez lecteur de disquette (‘Floppy disk drives’) et introduisez la disquette fournie avec, dans le lecteur de disquettes. Cliquez sur Suivant (‘Next’). 30/11/1999
31
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
Windows 98 détecté les pilotes du Proxima ISDN Lite. Cliquez sur Suivant (‘Next’).
Le système installe tous les pilotes et démarre l’utilitaire de configuration.
Les pilotes suivants sont installés automatiquement: Proxima ISDN Lite V.120 Proxima ISDN Lite PPP Proxima ISDN Lite V.110 Proxima ISDN Lite ML-V.120 Proxima ISDN Lite ML-PPP
Protocole V.120 – 64 Kbps Protocole PPP – 64 Kbps Protocole V.110 Protocole multilink V.120– 128 Kbps Protocole multilink PPP – 128 Kbps
Remarque: Windows vous fait croire qu'à chaque protocole correspond un appareil distinct. Tous les protocoles sont toutefois utilisés par un seul appareil. Quand la procédure d’installation est terminée, enlevez la disquette, cliquez sur ‘Reboot’. L’ordinateur est redémarré.
30/11/1999
32
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
Si tout s'est bien déroulé, vous pouvez passer au chapitre 3, ‘L’installation de l’utilitaire de configuration sous Windows 95/98/NT’. Dans l'autre cas, vous pouvez installer manuellement les pilotes pour le Bausch Proxima ISDN Lite (voir chapitre 2.3, ‘Installation manuelle des pilotes sous Windows 95/98/NT’).
30/11/1999
33
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
2.2 Installation Plug & Play sous Windows 95. Après le démarrage de l'ordinateur, Windows 95 vous avertit qu'il a détecté un nouveau périphérique. Les captures d'écran suivantes proviennent de Windows 95, version anglaise. L'installation se déroule comme suit: Cliquez sur Suivant (‘Next’).
Introduisez la disquette fournie avec votre Proxima ISDN Lite dans le lecteur de disquettes. Windows 98 détecté les pilotes du Proxima ISDN Lite. Cliquez ensuite sur Terminer (‘Finish’).
Le système installe tous les pilotes et démarre le logiciel de configuration. 30/11/1999
34
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
Remarque: dans certaines versions de Windows 95 la procédure d’installation automatique est interrompu. Windows 95 vous demande alors de sélectionner manuellement le lecteur approprié. Dans ce cas, tapez A:\ et l’installation se poursuit. Selon le protocole du canal B les pilotes suivants sont installés automatiquement: Proxima ISDN Lite V.120 Proxima ISDN Lite PPP Proxima ISDN Lite V.110 Proxima ISDN Lite ML-V.120 Proxima ISDN Lite ML-PPP
Protocole V.120 – 64 Kbps Protocole PPP – 64 Kbps Protocole V.110 Protocole multilink V.120– 128 Kbps Protocole multilink PPP – 128 Kbps
Remarque: Windows vous fait croire qu'à chaque protocole correspond un appareil distinct. Tous les protocoles sont toutefois utilisés par un seul appareil. Quand la procédure d’installation est terminée, enlevez la disquette, cliquez sur ‘Reboot’ et l’ordinateur sera redémarré.
Remarque: Si votre version de Windows 95 ne fait pas apparaître cette fenêtre, vous devez redémarrer votre ordinateur manuellement en exécutant les étapes suivantes: Cliquez sur le bouton Démarrer (‘Start’), ‘Shutdown’ et sélectionnez ‘Restart the computer’. Si tout s'est bien déroulé, vous pouvez passer au chapitre 3, ‘L’installation de l’utilitaire de configuration sous Windows 95/98/NT’. Dans l'autre cas, vous pouvez installer manuellement les pilotes pour le Bausch Proxima ISDN Lite (voir chapitre suivant, ‘Installation manuelle des pilotes sous Windows 95/98/NT’).
30/11/1999
35
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
2.3 Installation manuelle des pilotes sous Windows NT. Si votre ordinateur est déjà allumé ou s'il n'a pas détecté le nouveau périphérique, vous devez exécuter les étapes suivantes: 1.
Cliquez sur le bouton Démarrer (‘Start’), sélectionnez Paramètres (‘Settings’) et cliquez sur Panneau de configuration (‘Control Panel’).
2.
Le panneau de configuration apparaît. Double-cliquez sur Modems. Puisque Windows ne fait pas la distinction entre appareils ISDN et analogiques, votre Bausch Proxima ISDN Lite est piloté comme un ‘modem’.
3.
La fenêtre Modems (‘Modems Properties’, ‘General’) apparaît sur l'écran. Cliquez sur Ajouter (‘Add’).
4.
Cochez la case Ne pas détecter mon modem, sélection dans une liste (‘Don’t detect my modem ; I will select it from a list’). Un ‘v’ apparaît dans la case. Cliquez sur Suivant (‘Next’). Parfois il faut attendre quelques instants jusqu'à ce que Windows ait fini de constituer la base de données des pilotes.
5. Bien que plusieurs types de modem figurent dans la fenêtre suivante, vous 30/11/1999
36
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
devez installer un modèle à partir d'une disquette. Cliquez donc sur Disquette (‘Have Disk’).
6. Introduisez la disquette fournie dans le lecteur de disquettes. Sélectionnez le lecteur approprié et cliquez sur OK. 7. La fenêtre suivante apparaît:
8.
Sélectionnez un des pilotes suivants à installer selon le protocole désiré du canal B: Proxima ISDN Lite V.120 Protocole V.120 – 64 Kbps Proxima ISDN Lite PPP Protocole PPP – 64 Kbps Proxima ISDN Lite V.110 Protocole V.110 Proxima ISDN Lite ML-V.120 Protocole multilink V.120–128 Kbps Proxima ISDN Lite ML-PPP Protocole multilink PPP – 128 Kbps
30/11/1999
37
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
Remarque: Windows vous fait croire qu'à chaque protocole correspond un appareil distinct. Tous les protocoles sont toutefois utilisés par un seul appareil.Exemple: • • 9.
Bausch Proxima ISDN Lite PPP pour connexion ISP (Internet Service Provider). Bausch Proxima ISDN Lite V.120 pour la communication avec un BBS.
Cliquez sur Suivant (‘Next’).
10. Une nouvelle fenêtre apparaît dans laquelle il faut sélectionner le port série auquel est raccordé le Proxima ISDN Lite (en général COM2). Sélectionnez le port et cliquez ensuite sur Suivant (‘Next’). 11. La fenêtre suivante apparaît contenant le message Votre modem est installé (‘Your modem has been set up successfully’). Cliquez sur Terminer (‘Finish’).
Si vous voulez installer plusieurs protocoles du canal B, il suffit de répéter les étapes 8 à 11. La procédure d'installation est terminée.
30/11/1999
38
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
3. L’installation de l’utilitaire de configuration ‘Configuration Tool’ sous Windows 95/98/NT. L'installation Plug & Play des pilotes sous Windows 95/98 (chapitres 2.1 et 2.2) est suivie de l'installation de l’utilitaire de configuration. Si vous êtes en train d'installer manuellement (chapitre 2.3: installation des pilotes sous Windows NT), vous pouvez installer l’utilitaire de configuration en cliquant sur Démarrer (‘Start’), Exécuter (‘Run’) et en tapant A:SETUP. Cliquez ensuite sur OK. Le premier écran apparaît. Cliquez sur Suivant (‘Next’).
Dans les écrans suivants, vous pouvez choisir un autre dossier et groupe de programmes pour installer les fichiers de configuration. Si le dossier et groupe standards vous conviennent, il suffit de cliquer dans les deux écrans sur ‘Next’.
30/11/1999
39
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
Cliquez ensuite sur ‘Finish’ pour achever l'installation et pour démarrer le logiciel de configuration. Veillez à ce que le Bausch Proxima ISDN Lite soit raccordé et mis sous tension.
30/11/1999
40
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
4. Configuration du PROXIMA ISDN LITE. Le logiciel de configuration cherche le Bausch Proxima ISDN Lite (le numéro de version peut être différent du numéro affiché). Cliquez sur ‘Next‘ afin de poursuivre la configuration.
Configuration des numéros MSN. Une ligne ISDN vous permet de demander à l'opérateur jusqu'à 8 numéros de téléphone. Dans beaucoup de pays l’opérateur vous permet d’avoir différents numéros attribués à une ligne ISDN. En France par exemple, vous obtiendrez 1 numéro principal et 3 numéros supplémentaires en option. Si vous souhaitez plus de numéros, vous devez en faire la demande. En Belgique à la demande d’une ligne ISDN standard BRA (ISDN-2) vous obtiendrez 1 numéro principal. Des numéros supplémentaires sont optionnels, mais payants. Une connexion TWIN de Belgacom vous permet d’obtenir deux numéros principals; des numéros supplémentairs sont aussi optionnels et payants. Ce service s'appelle MSN (Multiple Subscriber Numbers ou Numéros d'abonnée multiples). Avec le Bausch Proxima ISDN Lite vous pouvez attribuer à chaque numéro de téléphone un protocole. Si ce numéro est appelé, le Bausch Proxima ISDN Lite établira une communication selon le protocole configuré. Un écran, comme celui à la page suivante, permet d'entrer tous les numéros MSN qui correspondent à la connexion ISDN-2. Cliquez sur ‘Next’ pour continuer. 30/11/1999
41
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
Dans l'écran suivant, vous avez la possibilité d’attribuer un numéro MSN à un protocol spécifique du canal B. Si vous optez pour ‘all numbers’, le Proxima Lite ISDN établira une connexion ISDN sur tous les numéros. Si vous, au contraire, choisissez ‘none’, le boîtier ne réagira pas.
Remarque: assurez-vous que votre logiciel (RVS-Com Lite, BVRP ou DUN/RAS) est activé pour pouvoir réceptionner des appels! Cliquez sur ‘Next’ pour l’écran suivant.
30/11/1999
42
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
La fonction ‘Connected Line Identification Presentation’ (‘COLP’) permet d'entrer le numéro désiré (le numéro de l'appelant) qui sera visible sur l'écran de l'appelé avant qu'il ne réponde à l'appel. En optant pour ‘main number’, vous entrez le numéro principal. ‘Default data protocol’ indique le mode adopté par le terminal (protocol du canal B) lors du démarrage ou de la réinitialisation de l'appareil. Cliquez sur ‘Next’ pour afficher l'écran suivant.
Cliquez sur ‘Finish’. Les paramètres sont envoyés vers le Proxima ISDN Lite et sauvegardés. 30/11/1999
43
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
Ceci termine la configuration de votre Bausch Proxima ISDN Lite. A présent, votre Proxima ISDN Lite est configuré et prêt à l'emploi. Bonne chance. Cliquez sur ‘Exit’ pour quitter l’utilitaire de configuration.
30/11/1999
44
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
Installation Guide
BAUSCH PROXIMA ISDN LITE
30/11/1999
45
Bausch Datacom
Proxima ISDN Lite
30/11/1999
Installatiehandleiding
46
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
TABLE OF CONTENTS INTRODUCTION
49
1. CONNECTING THE PROXIMA ISDN LITE
50
2. DRIVER INSTALLATION
51
2.1. PLUG & PLAY INSTALLATION IN WINDOWS 98 2.2. PLUG & PLAY INSTALLATION IN WINDOWS 95 2.3. MANUAL INSTALLATION IN WINDOWS NT
51 54 56
3. INSTALLATION OF THE CONFIGURATION SOFTWARE
58
4. HOW TO CONFIGURE THE PROXIMA ISDN LITE
61
30/11/1999
47
Bausch Datacom
Proxima ISDN Lite
30/11/1999
Installatiehandleiding
48
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
Introduction Congratulations with the purchase of your Bausch Proxima ISDN Lite. If you want to set up a high speed ISDN Internet connection, you will be pleasantly surprised by this product. With the included communication software (RVS-Com Lite and/or BVRP) you can easily set up Internet connections, send and receive faxes and use the Proxima ISDN Lite as an answering machine. The user manual in 3 languages (Dutch/French/English) ensures a smooth installation. With the included configuration tool you will be able to configure the B-channel protocol and the MSN numbers in no time. Because of all this, the Bausch Proxima ISDN Lite is a gem with the best price/quality proportion you can find on the market. This installation guide explains how to connect the Bausch Proxima ISDN Lite to your PC and how to properly install the drivers. It also explains how to use the ‘Configuration Tool’ software. This installation guide includes the following chapters: 1. 2.
3. 4.
Connecting the Bausch Proxima ISDN Lite. Driver installation. 2.1. Plug & Play installation in Windows 98. 2.2. Plug & Play installation in Windows 95. 2.3. Manual installation in Windows NT. Installation of the configuration software. How to configure the Proxima ISDN Lite ?
You can find extended information on all commands for the Bausch Proxima ISDN Lite in the user manual.
The Bausch Proxima ISDN Lite comes with the following accessories: -
ISDN connection cable (RJ-45). Serial cable (RS-232). Power supply. RVS-Com Lite and/or BVRP communication software on CD-ROM. Driver disk and configuration software. Free Internet access. User instructions. This installation guide (of course).
30/11/1999
49
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
1. Connecting the Bausch Proxima ISDN Lite. This paragraph explains how to connect the Bausch Proxima ISDN Lite.
Description of the LED’s from left to right TD RD CD OH AA HS DTR MR PWR
1
Transmitted data Received data Carrier detect Channel B1 in use Ring indicator Channel B2 in use Data terminal ready Clear to send Power
Take the ISDN cable and click the (small) RJ-11 plug in the SO-Bus on the back of the Bausch Proxima ISDN Lite. After that, click the (big) RJ-45 plug in the Belgacom TWIN/BRA (for Belgium) or in the wall socket.
2. Using the serial cable (RS-232), connect the serial port of the Bausch Proxima ISDN Lite to the serial port on the computer. 3. Connect the power supply to the Bausch Proxima ISDN Lite (Power = PWR on the back). 4.
Turn on the computer.
The Bausch Proxima ISDN Lite is now connected. 30/11/1999
50
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
2. Driver installation. Before you can actually use the Proxima ISDN Lite, you need to install the drivers. If you use Windows 95 or 98, the drivers will automatically be installed because of the Windows Plug & Play feature. If you use Windows NT, the installation needs to be done manually.
2.1 Plug & Play Installation in Windows 98. After you have turned on the computer, Windows 98 will indicate that new hardware has been found. The installation then proceeds as follows: Click Next.
Click Next. 30/11/1999
51
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
Mark the option Floppy disk drives so Windows will know where to find the necessary drivers. Put the driver disk in the disk drive and click Next.
Windows will confirm the presence of the correct drivers. Click Next.
30/11/1999
52
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
All necessary files will now be copied to the computer.
All different ‘modems’ (one ‘modem’ for each possible ISDN B-channel protocol) will now automatically be installed. Proxima ISDN Lite V.120 Proxima ISDN Lite PPP Proxima ISDN Lite V.110 Proxima ISDN Lite ML-V.120 Proxima ISDN Lite ML-PPP
V.120 protocol – 64 Kbps PPP protocol – 64 Kbps V.110 protocol multilink 120 protocol–128 Kbps multilink PPP protocol–128 Kbps
Windows implies you need a separate ‘modem’ for each protocol, but actually one ‘modem’ (in this case the Bausch Proxima ISDN Lite) can handle all these protocols. You will have to reboot your computer upon completion of the installation. Make sure you remove the driver disk from the disk drive. Then Reboot.
If you succeeded in all the above steps, you can continue with Chapter 3, ‘Installation of the configuration software’. In case you did not succeed in all the above steps, you can install the Bausch Proxima ISDN Lite manually, as described in Chapter 2.3, ‘Manual installation in Windows NT’.
30/11/1999
53
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
2.2 Plug & Play Installation in Windows 95. After you have turned on the computer, Windows 95 will indicate new hardware has been found. The installation goes as follows: After Windows 95 has detected the Bausch Proxima ISDN Lite, the following screen will appear. Click Next.
Insert the driver disk in the disk drive and click Finish.
All necessary files will now be copied to the computer. 30/11/1999
54
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
Remark: In some versions of Windows 95 the automatic installation procedure can be interrupted. In that case you will have to define the location of the disk drive manually. Just type A:\ After that the installation will continue as planned. The different ‘modems’ (one ‘modem’ for each possible ISDN B-channel protocol) will now be installed automatically. Proxima ISDN Lite V.120 V.120 protocol – 64 Kbps Proxima ISDN Lite PPP PPP protocol – 64 Kbps Proxima ISDN Lite V.110 V.110 protocol Proxima ISDN Lite ML-V120 multilinkV120protocol–128 Kbps Proxima ISDN Lite ML-PPP multilink PPP protocol–128 Kbps Windows implies you need a separate ‘modem’ for each protocol, but actually you only need one (in this case, the Bausch Proxima ISDN Lite) which can handle all these protocols. You will have to reboot your computer upon completion of the installation. Make sure you remove the driver disk from the disk drive. Then Reboot.
Remark: Some versions of Windows 95 will not show the above screen. In that case you will have to reboot the computer yourself. To do so, go to Start, Shutdown and then select Restart the computer. If you succeeded in all the above steps, you can continue with Chapter 3, ‘Installation of the configuration software’. If you did not succeed in all the above steps, you can install the Bausch Proxima ISDN Lite manually, as explained in Chapter 2.3, ‘Manual installation in Windows NT’.
30/11/1999
55
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
2.3 Manual installation in Windows NT. In case your system did not detect new hardware or is already turned on, you will have to follow the following steps. Click the Start button in the taskbar, then select Settings, then Control panel and go to Modems. Since Windows does not know any specific ISDN hardware, a Terminal Adapter such as the Bausch Proxima ISDN Lite will be recognized as a modem. You now get the screen install new modem (‘Modems Properties’, ‘General’). Click Add. Make sure you check the box Don’t detect my modem; I will select it from a list. Click Next.
The following screen shows all different types of modems. However, you need to install the driver from the driver disk you received with your modem. So, choose Have Disk.
30/11/1999
56
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
Insert the driver disk in the disk drive. Select the right driver and click OK. The following screen will appear:
Select the type that needs to be installed, for example: • Bausch Proxima ISDN Lite PPP for communication with an ISP (Internet Service Provider). • Bausch Proxima ISDN Lite V.120 for communication with a BBS (Bulletin Board System). Click Next.
30/11/1999
57
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
You now get a screen that allows you to choose the serial port the Bausch Proxima ISDN Lite needs to be connected to. In general this is COM2. Select the port and click Next. After that, the final screen will appear: your modem has been set up successfully. Click Finish.
If you want to install several protocols, you can do so by repeating the last steps. After this the installation is completed. Remark: Windows implies you need a separate ‘modem’ for each protocol, but actually one ‘modem’ (in this case the Bausch Proxima ISDN Lite) can handle all these protocols.
3. Installation of the configuration software. After the Plug & Play installation of the drivers in Windows 95/98 (chapter 2.1 en 2.2), the installation of the configuration software has started automatically. After that the opening screen, as shown on top of the next page, will appear. In case you are installing everything manually (chapter 2.3) in Windows, you can install the configuration software by going to Start, Run and then type A:SETUP. After that you click OK. The opening screen, which you can find at the top of the next page, will appear. Then click Next. Remark: before starting with the configuration, you should close all programs in Windows. If you closed all programs, continue with the configuration (see above: installing the configuration software after a manual installation of the drivers).
30/11/1999
58
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
In the next screens you can adjust the folder and program group where the configuration files will be installed in. Click Next for default folder and program group.
30/11/1999
59
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
Click Finish to complete Setup and start the configuration software. Make sure the Bausch Proxima ISDN Lite is connected and turned on.
30/11/1999
60
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
4. How to configure the Proxima ISDN Lite ? The configuration tool will search for the Proxima ISDN Lite (the version of the tool may differ from the one shown here). Click Next to continue with the configuration.
Configuring the MSN-numbers. When you switch to an ISDN connection, it is possible to apply for more than 1 and maximum 8 phone numbers from your telecom operator. The telecom operator supplies 1 main number for a standard connection. You can apply for additional numbers, but you will have to pay for them. With an ISDN-Twin connection (Belgium), your telecom operator (Belgacom in this case) offers you 2 numbers. You can ask for additional numbers, but you will also have to pay for them. This service is often referred to as MSN (‘Multiple Subscriber Numbers’). You can configure the Bausch Proxima ISDN Lite so you can assign a phone number to a protocol. When someone calls this number, the Bausch Proxima ISDN Lite will establish the connection according to the set protocol. As you can tell by the screen on the next page, you can fill out all the MSNnumbers of the ISDN-2 connection.
30/11/1999
61
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
Click Next to continue. In the next screen you need to specify which MSN-number you want to match a given B-channel protocol. You can choose this for each phone number. If you choose for all numbers the phone will ring for each MSN-number. If you choose for none the phone will never ring.
Remark: please note that application software needs to be active in order to detect an incoming call. Possible software can be RVS-Com Lite, BVRP or DUN/RAS. Click Next. 30/11/1999
62
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
In the ‘Connected Line Identification Presentation’ (COLP) screen, the caller’s phone number needs to be filled out. This number will show up on the display on the other side, even before the phone is being answered. When you choose for main number, the main number will appear. CLIP = to display an incoming number. COLP = to display an outgoing number. This number will be an incoming number (CLIP) on the other side. The Default data protocol indicates which B-channel protocol will be used as default when the Proxima ISDN Lite is turned on, or when you reset it. Click Next for the following screen.
By clicking Finish the configuration settings will be send to the Bausch Proxima ISDN Lite. 30/11/1999
63
Bausch Datacom
Proxima ISDN Lite
Installatiehandleiding
The Bausch Proxima ISDN Lite is now ready to use. Clik Exit to leave the configuration tool.
30/11/1999
64
Bausch Datacom