Normen voor kunststoffen EC Regulations and standardisation
3 Oktober 2013 Plastic Vision - Kortrijk
Dirk De Moor – Federplast (Agoria – essenscia) • Verantwoordelijk voor de sectoroperator Sirris-Agoria • Reglementering liften • De bouwproductenverordening • Secretaris en lid RvB EuCIA • Eu projecten ivm conforme koeling van matrijzen en thermovormen
Inhoud • • • •
Het nut van normen Hoe normen zoeken Normen voor kunststoffen Assistentie
Het nut van normen
4
Het nut van normen Terminologie o Thermoplastische buizen en toebehoren voor het transport van fluïda Algemene definities, nominale waarden en toegelaten maatafwijkingen NBN T 42-003
5
Het nut van normen Compatibiliteit o Kunststofleidingsystemen voor warm- en koudwaterinstallaties - Vernet polyethyleen (PE-X) - Deel 2: Buizen NBN EN ISO 15875-2 o Kunststofleidingsystemen voor warm- en koudwaterinstallaties - Polybuteen (PB) - Deel 3: Hulpstukken NBN EN ISO 15876-3
6
Het nut van normen Testmethoden (eigenschappen, materiaalsamenstelling, ...) o Methode voor de beoordeling van het PVC-gehalte op basis van het totale chloorgehalte NBN EN 1995 o Beproevingsmethode voor het bepalen van de weerstand tegen veroudering door (natuurlijke) weersomstandigheden NBN EN ISO 16871 o Beproevingsmethoden voor het vaststellen van de lekdichtheid van de wand onder korte-duur inwendige druk NBN EN 1229 o Beproevingsmethoden voor de lekdichtheid van verbindingen met ringafdichtingen van elastomeren NBN EN 1277 o Leidraad voor conformiteitsbeoordeling NBN CEN ISO/TS 15875-7
7
Nut van normen Installatierichtlijnen o Aanbevolen richtlijnen voor de installatie NBN CEN/TS 14578 o Leidraad voor de installatie NBN CEN/TS 1852 o Horizontale cilindrische reservoirs van gewapende thermohardende kunststoffen met een inhoud van 0,5 tot 250 m3 voor vloeistoffen (vlampunt <= 55 °C) Transport, plaatsing en aansluiting NBN T 41-015
8
Het nut van normen Process o Polyethyleen leidingssystemen - Richtlijnen voor de opleiding, kwalificatie en herkeuring van lassers voor stuik, mof- en elektrolassen NBN T 42-011
9
Het nut van normen Voldoen aan de wetgeving – geharmoniseerde normen o 2006/42/EC Machinery (MD) o (EC) 1907/2006 Chemical substances (REACH) o (EU) 305/2011 Construction products (CPR)
10
Het nut van normen (EU) 305/2011 Construction products (CPR) Reference and title of the harmonised standard (and reference document)
Date of Date of the applicability of end of the cothe standard as existence a harmonised period standard
EN 40-7:2002 Lighting columns - Part 7: Requirements for fibre reinforced polymer composite lighting columns
01/10/2003
01/10/2004
EN 438-7:2005 High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 7: Compact laminate and HPL composite panels for internal and external wall and ceiling finishes
01/11/2005
01/11/2006
EN 681-2:2000 Elastomeric Seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 2: Thermoplastic elastomers
01/01/2003
01/01/2004
EN 1013:2012 Light transmitting single skin profiled plastics sheets for internal and external roofs, walls and ceilings - Requirements and test methods
01/09/2013
01/09/2014
EN 13165:2012 Thermal insulation products for buildings - Factory made rigid polyurethane foam (PU) products Specification
01/09/2013
01/09/2013
EN 13245-2:2008 Plastics - Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications - Part 2: PVC-U profiles and PVC-UE profiles for internal and external wall and ceiling finishes
01/07/2010
01/07/2012
EN 13341:2005+A1:2011 Static thermoplastic tanks for above ground storage of domestic heating oils, kerosene and diesel fuels - Blow moulded and rotationally moulded polyethylene tanks and rotationally moulded tanks made of anionically polymerized polyamide 6 - Requirements and test methods
01/10/2011
01/10/2011
EN 14309:2009+A1:2013 (new) Thermal insulation products for building equipment and industrial installations - Factory made
11 01/11/2013
01/11/2013
Hoe normen zoeken?
12
Hoe normen zoeken? Via het normalisatiedomein: • Telecommunicatie (ITU , ETSI) • Elektrotechniek (IEC , CENELEC) • Alle domeinen, uitgezonderd telecommunicatie en elektrotechniek • ISO www.iso.org • CEN www.cen.eu/esearch Via nationale normalisatie-instellingen: • cat.nbn.be/nederlands/catalogus.htm • www.ceb-bec.be/nl/external/webstore • www.nen.nl -> geeft de eerste bladzijden van de norm onder pdf vorm • www.boutique.afnor.org
13
Hoe normen zoeken? Hoe zoeken? • Trefwoorden: Taalgebruik! Nationale normen bestaan enkel in de officiële nationale talen. Europese normen in het Engels, Frans en Duits. Internationale normen in het Engels, Frans (en Russisch). Gebruik zoekwoorden in de betreffende talen. • ICS code (International Classification for Standards) • Richtlijn Tip: eens relevante normen gevonden, best de commissie noteren. Misschien zijn er nog andere relevante normen in deze commissie?
14
Normen voor kunststoffen
15
16
17
18
19
20
21
Normen voor kunststoffen 65 67 71 73 75 77 79 81 83 85 87 91 93
Agriculture Food technology Chemical technology Mining and minerals Petroleum and related technologies Metallurgy Wood technology Glass and ceramics industries Rubber and plastic industries Paper technology Paint and colour industries Construction materials and building Civil engineering
22
23
24
25
Normen voor kunststoffen CEN TC 145 Plastics and rubber machines CEN TC 155 Plastics piping systems and ducting systems CEN TC 208 Elastomeric seals for joints in pipework and pipelines CEN TC 210 GRP tanks and vessels CEN TC 218 Rubber and plastics hoses and hose assemblies CEN TC 249 Plastics CEN TC 266 Thermoplastic static tanks
26
CEN TC 145 Plastics and rubber machines WG 1 Injection moulding machines - Safety WG 2 Compression moulding machines - Safety WG 3 Extruders and extrusion lines - Safety WG 4 Two roll mills - Safety WG 5 Blow moulding machines - Safety WG 6 Size reduction machines - Safety WG 7 Internal mixers - Safety WG 8 Calenders - Safety WG 9 Reaction injection moulding machines - Safety WG 10 Thermoforming machines - Safety WG 12 Winding machines for film or sheet - Safety WG 14 Welding machines for plastics - Safety WG 15 Cutting and processing polyurethane and latex foam machines - Safety WG 17 Tyre curing presses
27
CEN TC 155 Plastics piping systems and ducting systems WG 1 Installation outside building structures of flexible piping systems WG 6 Systems for soil and waste discharge - PVC-U WG 8 Systems for water supply and pressure drainage and sewerage - PVC-U (solid wall) WG 10 Systems of polyolefin material for soil & waste discharge and non-pressure drainage and sewerage WG 12 Pressure systems of polyolefin material for gas supply, water supply and drainage and sewerage WG 13 Systems with structured-wall pipes for non-pressure drainage and sewerage - PE, PP, PVC-U WG 14 Systems of glass-reinforced thermosetting plastics for all applications - Polyester, epoxy and polyester resin based concrete WG 15 Pipes and fittings for piping systems for rainwater discharge WG 16 Systems for hot and cold water applications WG 17 Plastic components for the use of renovation of piping systems WG 20 Thermoplastics ancillaries for soil and waste discharge and gravity buried drainage and sewerage systems WG 21 Assessment of conformity WG 23 Thermoplastics systems for industrial applications WG 25 Recycling of PVC-U, PE and PP materials WG 26 Systems for storm water handling WG 27 Environmental aspects
28
CEN TC 208 Elastomeric seals for joints in pipework and pipelines WG 1 Elastomeric seals for hot and cold water and waste water WG 2 Elastomeric seals for gas, hydrocarbons and other fluids WG 3 Test methods for elastomeric seals
29
CEN TC 218 Rubber and plastics hoses and hose assemblies WG 1 Rubber and plastics hoses and hose assemblies for industrial, chemical and petrochemical applications WG 2 Rubber and plastics hoses and hose assemblies for hydraulic applications WG 4 Basic specifications and test methods for rubber and plastics hoses, hose assemblies and tubing WG 5 Couplings and hose fittings
30
CEN TC 249 Plastics WG 4 Decorative laminated sheets based on thermosetting resins WG 5 Thermoplastic profiles for building applications WG 7 Thermoplastic films for use in agriculture WG 8 Cellular plastics WG 9 Characterisation of degradability WG 11 Plastics recycling WG 12 Plastics jacketing WG 13 Wood Plastics Composites (WPC) WG 14 PVC-P swimming pool liners WG 15 Fibre-reinforced composites WG 16 Welding of thermoplastics WG 17 Biopolymers WG 19 Light exposure
31
CEN TC 266 Thermoplastic static tanks WG 2 Thermoplastic tanks fabricated by fusion techniques WG 3 Thermoplastic tanks made by the blow moulding and/or the rotational moulding processes WG 4 Thermoplastic tanks made by the blow moulding and/or the rotational moulding processes, for the storage of oils having a flash point above 55 °C or 60 °C
32
Normen voor kunststoffen ISO/TC 45
Rubber and rubber products
435 56
Standardization of terms and definitions, test methods and specifications for rubber in any form, rubber products (including their dimensional tolerances) and major rubber compounding ingredients.
ISO/TC 61
Plastics 630 93
Standardization of nomenclature, methods of test, and specifications applicable to materials and products in the field of plastics.
ISO/TC 138 Plastics pipes, fittings and valves for the transport of fluids 310 40 Standardization of pipes, fittings, valves and auxiliary equipments intended for the transport of fluids and made from all types of plastic materials, including all types of reinforced plastics.
ISO/TC 270 Plastics and rubber machines 0
0
Standardization in the field of machines used for the preparation, processing and recovery of plastics and rubber, including the detailed safety requirements for a particular machine or group of machines. Such requirements are applicable to the design, construction and use of machinery used in the plastics and rubber industry, addressing hazards, hazardous situations and hazardous events. Moreover, the Technical Committee could take into consideration other aspects such as machine classification and measurement of energy consumption. 33
ISO/TC 61 Plastics Subcommittee/Working Group Title ISO/TC 61/SC 1 Terminology ISO/TC 61/SC 2 Mechanical properties ISO/TC 61/SC 4 Burning behaviour ISO/TC 61/SC 5 Physical-chemical properties ISO/TC 61/SC 6 Ageing, chemical and environmental resistance ISO/TC 61/SC 9 Thermoplastic materials ISO/TC 61/SC 10 Cellular plastics ISO/TC 61/SC 11 Products ISO/TC 61/SC 12 Thermosetting materials ISO/TC 61/SC 13 Composites and reinforcement fibres
34
ISO/TC 61/SC 11 Products WG 2 WG 3 WG 5 WG 6 WG 7 WG 9 WG 10 WG 11
Decorative laminates and solid surfacing materials Plastics films and sheeting Polymeric adhesives Poly(methyl methacrylate) sheets Polycarbonate sheets WG 8 Unplasticized poly(vinyl chloride) sheets Plastic railway sleepers railroad ties Blow-moulded plastic products Wood-plastic composites
35
Assistentie
36
Assistentie Sector operator BECETEL Hubert Janssens, Gontrode Heirweg 130 9090 Melle Tel: 09 272 50 70,
[email protected]
CEN
titel
ISO
titel
155
Plastics piping systems and ducting systems
138
Plastics pipes, fittings and valves for the transport of fluids
208
Elastomeric seals for joints in pipework and pipelines
218
Rubber and plastics hoses and hose assemblies
45/1
Hoses (rubber and plastics)
266
Thermoplastic static tanks
249
Plastics
61
Plastics
45
Rubber and rubber products 37
Assistentie Sector operator Sirris-Agoria Diamant Building, August Reyerslaan 80, 1030 Brussel Tel: 02 706 79 84,
[email protected]
CEN
titel
210
GRP tanks and vessels
ISO
titel
38
Dank u voor uw aandacht! Vragen?
39
