EU bejelentett testület: MKEH Notified body: Hungarian Trade Licensing Office
Azonosítási szám: 1422 MAGYAR KERESKEDELMI ENGEDÉLYEZÉSI HIVATAL
Hungarian Trade Licensing Office
Identification number:
Ügyiratszám: TH-8629/3/2011
METROLÓGIAI FŐOSZTÁLY
File number:
Department of Metrology
H-1124 Budapest, Németvölgyi út 37-39 H-1535 Budapest Pf.: 919, fax (36)-1-4585 927
EK-TÍPUSVIZSGÁLATI TANÚSÍTVÁNY EC-type examination certificate (TEC)
A 2004/22/EK irányelveket honosító 8/2006. (II.27.) GKM rendelet alapján a következő EK-típusvizsgálati tanúsítványt adtuk ki. In accordance with the requirement of the decree of the Minister of Economy and Transport 8/2006. (II.27) implementing the Directive 2004/22/EC on the measuring instruments certificate of EC-type examination has been issued.
Alkalmazott harmonizált szabványok és normatív dokumentum: OIML R49-1:2006, OIML R49-2:2006 Harmonised standards and normative documents: OIML R49-1:2006, OIML R49-2:2006
Kérelmező: / Issued to:
Megnevezés / In respect of:
MOM Vízméréstechnikai ZRt H 4700 Mátészalka Ipari út 16. Magyarország / Hungary háztartási hidegvízmérő Domestic cold-water meter
Típusjelölés:/ Marking of type
M-MKNR a vízmérő számlálójában az „x l-es” mutatója egy jeladó mágnest tartalmaz. An indicator magnet to be set on the 1 liters indicator in the counting mechanism.
CORONA MCI a vízmérő számlálójában az „1 l-es” mutatóra egy korrózióálló tárcsa van szerelve A non-corrosion plate to be set on the 1 liters indicator in the counting mechanism
Névleges átmérő DN
DN15
nominal diameter DN
Névleges térfogatáram Q 3 Nominal flowrate Q3 [m 3 /h] Q 3 /Q 1 Q 2 /Q 1
DN20
DN25
DN20
2,5
4
40; 50; 63; 80; 100
40; 50; 63; 80; 100; 125; 160
1,6
Kivitel/ version
Alapmérő / normal version
Beépítési helyzet / Installation Max. üzemi nyomás MAP Max. working pressure (bar) Max. üz. hőmérséklet MAT Max working temp °C Nyomásveszt. osztály ∆p Class of Pressure loss Áraml. profil érzékenység
H
Felszállóágas mérő ascending pipe version
H; V-R40 16 30; 50 63 U0/D0
flow profil sensitivity class
Engedély száma / Approval number:
TH-8629/3/2011
Érvényes / Valid until:
2021. május 31.
Oldalak száma: /Number of pages:
16
Az azonosításhoz szükséges információkat (fő adatok, funkciók, lezárás, stb.) és a típusvizsgálati feltételeket (ha ilyenek vannak) ezen tanúsítvány és annak részét képező melléklet tartalmazza. The necessary data (principal characteristics, functions, securing, etc.) for identification purposes and conditions (when applicable) are set out in this certificate and in the descriptive annex, which forms an integral part of this certificate.
Budapest, .......................................................... Mónus Ferenc Igazgató / director
MAGYAR KERESKEDELMI ENGEDÉLYEZÉSI HIVATAL METROLÓGIAI FŐOSZTÁLY
Engedély száma: TH-8629/3/2011 Approval number: page 2 of 15 pages
2/15 oldal 1 A mérőeszköz megnevezése és típusjele: 1 Name and type of the instruments:
„Calyga” M-MKNR típusjelű háztartási hidegvízmérő. a vízmérő számlálójában az „1l-es” mutatón egy jeladómágnes található. Domestic cold-water meter „Calyga” M-MKNR An indicator magnet to be set on the 1 liters indicator in the counting mechanism.
CORONA MCI típusjelű háztartási hidegvízmérő. a vízmérő számlálójában az „1 l-es” mutatóra egy korrózióálló tárcsa van szerelve Domestic cold-water meter CORONA MCI A non-corrosion plate to be set on the 1 liters indicator in the counting mechanism.
2 A mérőeszköz leírása 2 Description of the type
A többsugaras nedvesenfutó háztartási hidegvízmérő visszacsapó szeleppel és opcionálisan felszerelhető impulzusadóval. A mérőbetét beszerelhető vízszintes és felszállóágas kivitelű, az 3. ábrán megadott vízmérőházakba. Domestic cold-water meter, multi jet, wet dial, with optional pulse output device and optional non-return (butterfly) valve. Measuring cartridge can be install in approved (horizontal or ascending pipe version) measuring house (figure 3).
3 Műszaki adatok 3 Technical data
3.1 Metrológiai adatok 3.1 Metrological data Névleges átmérő DN nominal diameter DN
Névleges térfogatáram Q 3 Nominal flowrate Q3 [m 3 /h] Q 3 /Q 1 Q 2 /Q 1 Beépítési helyzet / Installation Max. üzemi nyomás MAP Max. working pressure (bar) Max. üz. hőmérséklet MAT Max working temp °C Nyomásveszt. osztály ∆p Class of Pressure loss Áraml. profil érzékenység flow profil sensitivity class
DN15
DN20
2,5 40; 50; 63; 80; 100
DN25 4
40; 50; 63; 80; 100; 125; 160
1,6 H
H; V-R40 16 30; 50 63 U0/D0
Engedély száma: TH-8629/3/2011
MAGYAR KERESKEDELMI ENGEDÉLYEZÉSI HIVATAL METROLÓGIAI FŐOSZTÁLY
Approval number: page 3 of 15 pages
3/15 oldal 3.2 Mechanikai adatok 3.2 Mechanical data Kivitel/ version Névleges átmérő Nominal diameter
Csatlakozó menet Connection
Beépítési hossz Installation length
Beépítési helyzet Installation
Impulzusérzékelő Impuls sensor
Impulzusszám Impuls factor
Legkisebb osztásköz Reading step
Felszállóágas mérő
Alapmérő / normal version
ascending pipe version
-
DN 15
DN20
DN 25
DN20
-
G 3/4“
G 1“
G 5/4“
G 1“
mm
165; 170
190
175
105
-
H
H; V-R40
-
Reed vagy/ or „Hall”elem vagy/ or induktív 1
L/imp
1 vagy/ or 10 vagy/ or 100 vagy/ o r 1000
L
0,05
4 Jelölések, feliratok 4. Marks, inscriptions
A mérő számlapján és vagy a nézőüvegen az alábbi feliratok szerepelnek: Following inscriptions are on the mask of the watermeter: • A mértékegység jelölése: köbméter/Unit of measurement: cubic metre • A gyártó és opcionálisan a forgalmazó neve vagy jelölése / Name or trademark of the manufacturer or optional dealer • A gyártás éve / Year of manufacture • CE megfelelőségi jelölés / CE conformity marking • A típusengedély száma / Type approval number • Mérési tartomány és szerelési helyzet (V or H) / Measuring range and installation (V or H) • Q3 névleges térfogatáram m3/h-ban / Q3 Nominal flow in the m3/h • Maximális üzemi nyomás / Max. working pressure • Maximális üzemi hőmérséklet, ha T>30ºC / Max. working temperature • Áramlási profil érzékenység / flow profil sensitivity class • A gyártási szám /Serial number . • Egyéb opcionális jelzések /optional marking
A mérő fedelén az alábbi feliratok szerepelnek: • A gyártó vagy opcionálisan a forgalmazó jelölése / Name and trademark of the manufacturer or optional dealer •
Egyéb opcionális jelzések /optional marking A mérőházon az alábbi feliratok szerepelnek: • A mérőház mindkét oldalán megtalálható 1-1 nyíl az áramlási irány jelzésére. •
Two (1-1) arrows are on two side of the house idicating the flow direction Egyéb opcionális jelzések /optional marking
4.1 Forgalmazói jelölések 4.1. Distributor marks/logos
1
Induktív érzékelő esetén az impulzusszám mindig 1 L/imp / If Impuls sensor is inductive, then impuls factor always 1 L/imp
MAGYAR KERESKEDELMI ENGEDÉLYEZÉSI HIVATAL METROLÓGIAI FŐOSZTÁLY
4/15 oldal
Engedély száma: TH-8629/3/2011 Approval number: page 4 of 15 pages
5 Hitelesítés 5.Verification
A hitelesítés elvégezhető a komplett vízmérőn vagy külön a gyárilag lezárt önálló vízmérőbetéten. A vízmérőbetét önálló hitelesítését a 190 mm, G1 gyártási hosszúságú, a melléklet 6. ábráján bemutatott vízmérőházban kell elvégezni. A vízmérő betét önálló hitelesítése után az érvényességi idején belül az önállóan hitelesített vízmérőbetét bármilyen, jelen hitelesítési engedélyben meghatározott, új vagy felújított vízmérőházba beszerelhető. A vízmérőket az OIML R 49-2:2006 ajánlás 9.1 és 9.2 pontjai szerint kell hitelesíteni. The verification can be performed either on the complate meter or on the measuring cartridge which is protected against non-destructive opening. In case of verifications of only measuring cartridge, the measurements shall be made in the watermeter house with .lenght 190 mm, G1 (figure 3) After verification of measuring cartridge, the cartridge can be installed in the approved new or restored watermeter house. The watermeters shoud be verifyed according to the OIML R 49-2:2006, 9.1, 9.2.
6 Lezárás 6 Securing
Komplett vízmérő vizsgálata esetén függőhuzalos lezárást kell alkalmazni a zárógyűrű furata és a mérőházon található furat között, vagy öntapadós bélyeget kell elhelyezni a zárőgyűrű és a mérőház találkozásánál.(5,6,7 ábrák) A vízmérőbetét önálló hitelesítésekor azt nem kell bélyegezni. In case of verification of complete watermeter lead seals shall be applied between mortise of cover and a mortise of watermeter house (figures 5,6,7) or mark shall be applied on frontier of the cover and of the watermeter house. In case of verification only of measuring cartridge, the securing is not necessary.
7 A CE megfelelőségtanúsítási jel 7. CE conformity marking
A CE jelölést és a kiegészítő metrológiai jelölést a vízmérő számlapján vagy a mérőkapszula nézőelemén kell elhelyezni. (8. ábra) The CE marking and the supplementary metrology marking have to be placed on the dataplate or on the glass of the watermeter (figure 8.)
A CE megfelelőségtanúsítási jel egy nem eltávolítható címke formájában is elhelyezhető. (A kiegészítő metrológiai jelölés egy nagy M betűből, valamint a jelölés feltüntetése szerinti év utolsó két számjegyéből áll, amelyeket a CE jelölés magasságával azonos magasságú téglalap keretez. A kiegészítő metrológiai jelölés közvetlenül a CE jelölést követi.) CE conformity marking can be on the water meter with a non-removable stick-on label. (The supplementary metrology marking consists of the capital letter M and the last two digits of the year of its affixing, surrounded by a rectangle. The height of the rectangle shall be equal to the height of the CE marking. The supplementary metrology marking shall immediately follow the CE marking.)
8 Szerkezeti felépítés 8. Construction drawing
A mérőeszközök szerkezeti felépítését a mellékletben megadott ábrák mutatják. The is drawings of constructions are in the annex.
8.1 Engedélyezett kiegészítő egységek 8.1. approved devices • Visszacsapószelep / Non-return (Butterfly) valve (figure 5.)
Calyga” M-MKNR (7a. Ábra) • •
„ISAR P (vezetékes ) /ISAR P I (with wires) „ IZAR R (rádiós) jeladó IZAR R (radiofrekvency) HALL sensor CORONA MCI (7.b Ábra) • „ISAR P (vezetékes) induktív /ISAR P I (with wires) inductive • „ IZAR R (rádiós) jeladó / IZAR R (radiofrekvency) indicator „ IZAR D (mennyiségmérő) / IZAR D (Dosiemeter)
MAGYAR KERESKEDELMI ENGEDÉLYEZÉSI HIVATAL METROLÓGIAI FŐOSZTÁLY
5/15 oldal
Engedély száma: TH-8629/3/2011 Approval number: page 5 of 15 pages
10 Melléklet / Annex 1.a ábra: M-MKNR Vízmérő betét / M-MKNR measuring cartridge
Rajzszám: M-MKNR-0005B
MAGYAR KERESKEDELMI ENGEDÉLYEZÉSI HIVATAL METROLÓGIAI FŐOSZTÁLY
6/15 oldal
Engedély száma: TH-8629/3/2011 Approval number: page 6 of 15 pages
1.b ábra: CORONA Vízmérő betét / CORONA measuring cartridge
Rajzszám: CORONA MCI-0005B
MAGYAR KERESKEDELMI ENGEDÉLYEZÉSI HIVATAL METROLÓGIAI FŐOSZTÁLY
7/15 oldal 2. ábra: Számlálószerkezet / Counting mechanism
Engedély száma: TH-8629/3/2011 Approval number: page 7 of 15 pages
Rajzszám: M-MKNR-0006
Rajzszám: CORONA MCI-0006
MAGYAR KERESKEDELMI ENGEDÉLYEZÉSI HIVATAL METROLÓGIAI FŐOSZTÁLY
Engedély száma: TH-8629/3/2011 Approval number: page 8 of 15 pages
8/15 oldal 3. ábra: Avízmérő házak, engedélyezett hossz és csatlakozó méretei / Approved watermeter’s house
.
DN20-190 mm-es műanyag ház. (csak műanyag zárógyűrűvel szerelhető kivitel) Rajzszám:
M-MKNR-0004 CORONA MCI-0004
MAGYAR KERESKEDELMI ENGEDÉLYEZÉSI HIVATAL METROLÓGIAI FŐOSZTÁLY
9/15 oldal
Engedély száma: TH-8629/3/2011 Approval number: page 9 of 15 pages
Felszállóágas kivitel/ascending pipe version Qn 2,5 G1B 105 mm
Vízmérőház zárógyűrűvel A réz háznál réz és műanyag zárógyűrűvel szerelt kivitel
Műanyag vízmérőház műanyag zárógyűrűvel
. Rajzszám:
M-MKNR-0004 CORONA MCI-0004
MAGYAR KERESKEDELMI ENGEDÉLYEZÉSI HIVATAL METROLÓGIAI FŐOSZTÁLY
10/15 oldal 4.ábra Anyagjegyzék / List of parts
Engedély száma: TH-8629/3/2011 Approval number: page 10 of 15 pages
Rajzszám:
M-MKNR-0007-2 CORONA MCI-0007-2
Engedély száma: TH-8629/3/2011
MAGYAR KERESKEDELMI ENGEDÉLYEZÉSI HIVATAL METROLÓGIAI FŐOSZTÁLY
Approval number: page 11 of 15 pages
11/15 oldal Nr.
Megnevezés
Db
Vízzel érintkezik
Anyag
Description
pcs
Contacting with water
Material
CuZn40Pb2s PPA NBR ShA 70 PS vagy ABS CuZn40 NBR ShA 70 PA PS Présfólia vagy festék PA12
-
Impulzusérzékelő
1
nem
1
Zárógyűrű
1
igen
1 1 1 1 1 1 1
igen nem nem igen igen igen igen igen
2 3 4 5 6 7 7.1
O – gyűrű Fedél Tengely O – gyűrű „Nézőüveg” Számláló kpl Felső ágylap "Jelölés" - Présfóliázás 7.2 Persely 7.3 Számdobok kpl. 7.3.1 Kezdőszámdob "Jelölés" - Présfóliázás 7.3.2 Közbensőszámdob "Jelölés" - Présfóliázás 7.3.3 Hajtóka 7.3.4 Tengely 7.4 Fogaskerék I 7.5 Fogaskerék II 7.5 Fogaskerék III 7.7 Fogaskerék IV 7.8 Fogaskerék V 7.9 Fogaskerék VI 7.10 Fogaskerék VII 7.11 Fogaskerék VIII 7.12 Fogaskerék IX 7.13 Dobváltó 7.14 Csillagkerék 7.15.a Mutató 7.15.b Mutató jeladómágnessel 7.15.c Mutató jeladótárcsával 7.16 Alsó ágylap 8 Kerékház 9 Szárnyház Szárnykerék kpl Szárnykerék 10 Saphir 11 Szárnyház alsófél kpl. 12.a Alapcsap 12.b Alapcsap 13 Szárnyház alsófél 14 Szabályzógyűrű 15 Burkolat 16 O - gyűrű Védősapka 17
Vízmérőház
1 1
4 2 1 1 1 1 1 1 1 1 1 1 1 3 3 3 1 1 1 (1) 1 1 (1) 1 1 1 1 1 1 1
igen igen igen igen igen igen igen igen igen igen igen igen igen igen igen igen igen igen igen igen igen igen igen igen igen igen igen igen igen igen igen (igen)
1
igen
3
Rajzszám:
PS Présfólia PS Présfólia PS X5CrNiMo1812 PA12 PA12 PA12 PA12 PA12 PA12 PA12 PA12 PA12 PA12 PS POM vagy PS POM + keményferrit POM + Inox PS PS PS PS (Al2O3) PA+Carbon+PTFE Inox PS PP PS NBR ShA 70 PP CuZn40Pb2 PPA
M-MKNR-0007-1B CORONA MCI-0007-1B
MAGYAR KERESKEDELMI ENGEDÉLYEZÉSI HIVATAL METROLÓGIAI FŐOSZTÁLY
12/15 oldal
Engedély száma: TH-8629/3/2011 Approval number: page 12 of 15 pages
5. ábra: M-MKNR és CORONA MCI vízmérő lezárással / watermeter with securing Lezáró bélyegzés / securing* ólomzár vagy öntapadós címke / lead or stick-on label
Rajzszám: M-MKNR-0001 6.a ábra: M-MKNSR és CORONA MCI felszállóágas kivitel / ascending pipe version Lezáró bélyegzés / securing* ólomzár vagy öntapadós címke / lead or stick-on label
Rajzszám: M-MKNR-0002 * komplett vízmérő hitelesítése esetén/ In case of verifications of complete watermeter
MAGYAR KERESKEDELMI ENGEDÉLYEZÉSI HIVATAL METROLÓGIAI FŐOSZTÁLY
Engedély száma: TH-8629/3/2011 Approval number: page 13 of 15 pages
13/15 oldal 7.a ábra: M-MKNR vízmérő impulzusadóval / watermeter with pulse output device Lezáró bélyegzés/securing ólomzár vagy öntapadós címke / lead or stick-on label
Rajzszám: M-MKNR-0003 * komplett vízmérő hitelesítése esetén/ In case of verifications of complete watermeter
MAGYAR KERESKEDELMI ENGEDÉLYEZÉSI HIVATAL METROLÓGIAI FŐOSZTÁLY
Engedély száma: TH-8629/3/2011 Approval number: page 14 of 15 pages
14/15 oldal 7.b ábra: CORONA vízmérő impulzusadóval / watermeter with pulse output device Lezáró bélyegzés/securing ólomzár vagy öntapadós címke / lead or stick-on label
Rajzszám: CORONA MCI-003 * komplett vízmérő hitelesítése esetén/ In case of verifications of complete watermeter
MAGYAR KERESKEDELMI ENGEDÉLYEZÉSI HIVATAL METROLÓGIAI FŐOSZTÁLY
15/15 oldal
Engedély száma: TH-8629/3/2011 Approval number: page 15 of 15 pages
8. ábra: CE megfelelőségi jelölés / CE marking M-MKNR Gyártó jele manufacturer’s logo
CE jelölés CE markin
30 ºC-tól eltérő tip. esetén
forgalmazói jelölés distributor’s logo
CORONA MCI
CE jelölés CE markin
Gyártó jele manufacturer’s logo
30 ºC-tól eltérő tip. esetén