Národní bezpečnostní úřad
Certifikační postupu NBÚ – verze 2010
Schválil: Náměstek ředitele Národního bezpečnostního úřadu Ing. Jaroslav Šmíd
Praha
leden 2010
Informace k certifikačnímu postupu NBÚ Vzhledem k nutnosti zajistit u všech certifikovaných výrobků, používaných za účelem ochrany utajovaných informací, stálou kvalitu, dozor nad jejich výrobou či distribucí a stálost jejich požadovaných technických parametrů, přistupuje NBÚ ke sjednocení režimu certifikace a předkládá
dokument „Certifikační postupu NBÚ – verze 2010“. Tento
certifikační postup bude platný od 1. 1. 2010 souběžně se stávajícími certifikačními postupy (CP NBÚ č. 1 a CP NBÚ č. 2). Od 1. 1. 2011 bude certifikace prováděna pouze podle Certifikačního postupu NBÚ – verze 2010. Platnost certifikátů vydaných od 1. 1. 2010 na základě CP NBÚ č. 1, CP NBÚ č. 1 doplňku a CP NBÚ č. 2 je stanovena do 31. 12. 2012. Dokument popisuje proces certifikace výrobků jehož základem jsou systémy popsané v pokynu ISO/IEC 67 Posuzování shody – Základy certifikace produktů. Zkoušení výrobků je zajišťováno prostřednictvím zkušebních laboratoří, které splňují všeobecné požadavky ČSN EN ISO/IEC 17025:2005 nebo jiných typů orgánů podle ČSN EN ISO/IEC 17020:2005. Zkoušení technických prostředků je prováděno v souladu se specifikovanými normami a v souladu se systémem certifikace produktů podle uvedených příloh: a) mechanické zábranné prostředky – příloha č. 1.1 a příloha č. 1.2, b) elektrická zámková zařízení a systémy pro kontrolu vstupů – příloha č. 2, c) zařízení elektrické zabezpečovací signalizace – příloha č. 3, d) speciální televizní systémy – příloha č. 4, e) tísňové systémy – příloha č. 5, f) zařízení elektrické požární signalizace – příloha č. 6, g) zařízení sloužící k vyhledávání nebezpečných látek nebo předmětů – příloha č. 7, h) zařízení fyzického ničení nosičů informací – příloha č. 8, i)
zařízení proti pasivnímu a aktivnímu odposlechu utajované informace - příloha č. 9.
Součástí certifikačního postupu je i aktualizovaná metodika zkoušení odolnosti cylindrických vložek proti bumping metodě z 1.11.2009 (vzhledem k rozsahu není dokument přiložen). Platnost stávající metodiky zkoušení odolnosti proti bumping metodě bude do 30. 6. 2010. Od 1. 7. 2010 bude používána pouze tato aktualizovaná metodika.
2
Obsah
Strana/listů Certifikační postupu NBÚ – verze 2010
5
Příloha č. 1: Mechanické zábranné prostředky - písm. a) § 30 zákona
10
Příloha č. 1.1: Bezpečnostní úschovné objekty a jejich zámky • Bezpečnostní úschovné objekty • Trezory se základní bezpečností • Zámky se zvýšenou bezpečností (ZVB)
10/6 10 12 14
Příloha č. 1.2: Zabezpečené oblasti a jejich uzamykací systémy
16/18
• • • • • • • • •
Bezpečnostní otvorové výplně – dveře, okna, mříže apod. Cylindrické vložky – mechanické Cylindrické vložky – mechatronické Zámky a střelkové zámky a zapadací plechy - elektromechanicky ovládané Zámky a střelkové zámky a zapadací plechy - mechanicky ovládané Zámky a střelkové zámky a zapadací plechy - vícebodové zámky a zapadací plechy Dveřní štíty, kliky a knoflíky Jednoosé závěsy Visací zámky a příslušenství visacích zámků
16 19 21 23 25 27 29 31 33
Příloha č. 2: Elektrická zámková zařízení a systémy pro kontrolu vstupů – písm. b) § 30 zákona
35/2
Příloha č. 3: Poplachové systémy – elektrická zabezpečovací signalizace - písm. c) § 30 zákona
37/21
• • • • • • • •
Ústředna EZS Detektor pohybu – PIR, MW, UZ a kombinovaný Detektor rozbití skla Otřesový detektor Detektor směrový (závora) Detektor otevření Napájecí zdroj Bezdrátové systémy
Příloha č. 4: Speciální televizní systémy – písm. d) § 30 zákona – • Systémy CCTV, kamery • Systémy CCTV, řídící jednotky
37 42 45 47 49 52 54 56
58/4
58 60
3
Příloha č. 5: Tísňové systémy – písm. e) § 30 zákona
62/3
Příloha č. 6: Zařízení elektrické požární signalizace – písm. f) § 30 zákona
65/1
Příloha č. 7: Zařízení sloužící k vyhledávání nebezpečných látek nebo předmětů – písm. g) § 30 zákona 66/2 Příloha č. 8:Zařízení fyzického ničení nosičů informací – písm. h) § 30 zákona
68/1
Příloha č. 9: Zařízení proti pasivnímu a aktivnímu odposlechu utajované informace – písm. i) § 30 zákona 69/4 • • • •
Šumové generátory Akustické budiče Detektory aktivní mobilní a rádiové komunikace Radiové analyzátory
4
69 70 71 72
Certifikační postup NBÚ – verze 2010
1.1 Účel postupu Předkládaný Certifikační postup Národního bezpečnostního úřad stanovuje proces certifikace technických prostředků, které jsou používány pro ochranu utajovaných informací. Certifikací technických prostředků se rozumí způsobilost výrobků a zařízení k ochraně utajovaných informací, posouzení jejich technických parametrů a vystavení certifikátu na základě odborného posudku akreditované zkušební laboratoře podle § 46 zákona č. 412/2005 Sb., o ochraně utajovaných informací a o bezpečnostní způsobilosti, ve znění pozdějších předpisů (dále jen zákon č. 412/2005 Sb.). K vydávání odborného posudku, který slouží jako hlavní podklad pro vydání certifikátu, Národní bezpečnostní úřad uzavírá smlouvu o zajištění činností s odborným pracovištěm - certifikačním orgánem. Certifikát vystavuje Národní bezpečnostní úřad (dále jen NBÚ) na základě žádosti žadatele (tj. výrobce, dovozce nebo prodejce) zaslané v souladu s vyhláškou č. 528/2005 Sb, o fyzické bezpečnosti a certifikaci technických prostředků, ve znění vyhlášky č. 19/2008 Sb. (dále jen vyhláška č. č. 528/2005 Sb.). Náležitosti přikládané k žádosti o certifikaci technického prostředku jsou uvedeny v § 11 vyhlášky č. 528/2005 Sb. Seznam překládané dokumentace, včetně žádosti, je uveden také na internetových stránkách NBÚ v části fyzická bezpečnost. Účelem tohoto dokumentu je popsat u certifikačního orgánu provozované systémy certifikace výrobků, jejichž výstupy využívá NBÚ pro certifikaci technických prostředků podle § 46 zákona č. 412/2005 Sb. Základem předmětných systémů jsou systémy popsané v pokynu ISO/IEC 67 Posuzování shody – Základy certifikace produktů, přičemž je využit systém 1b, 3 a 5. Pro podrobnější rozpracování systému 5 je využit pokyn ISO/IEC 28 Posuzování shody – Návod týkající se systému certifikace produktů třetí stranou.
5
1.2 Předmět postupu Vytvoření příslušných výstupů pro následné ověření způsobilosti technického prostředku k ochraně utajovaných informací uvedeného § 30 písmeno a), b), c), d), e), f), g), h) a i) zákona č. 412/2005 Sb.
1.3 Požadavky na certifikační orgán K provozování těchto systémů certifikace produktů musí být certifikační orgán ve shodě s požadavky ČSN EN 45011:1998 a platného znění MPA 40-01-xx.
1.4 Žádost – přihláška k certifikaci Žádost – přihlášku k certifikaci realizuje zákazník na speciálním formuláři, který lze získat u příslušného certifikačního orgánu. V žádosti – přihlášce uvede přesnou specifikaci produktu nebo skupiny produktů, pro kterou je certifikace požadována a identifikaci norem – normy, s jejímiž požadavky je posouzení shody požadováno.
1.5 Příprava na hodnocení 1.5.1 Obecně Certifikační orgán je odpovědný za všechny činnosti zahrnuté v tomto schématu certifikace včetně vzorkování, zkoušení, posuzování produkčního procesu nebo systému kvality a dozoru nad certifikovaným produktem. Certifikační orgán může přijmout v souladu se schématem certifikace produktů existující výsledky posouzení shody. Pokud certifikační orgán zjistí, že nejsou všechny požadavky splněny, informuje o této skutečnosti zákazníka. Pokud prokáže zákazník, že bylo za účelem splnění požadavků v rámci specifikovaného časového termínu přijato opatření k nápravě, pak certifikační orgán opakuje pouze nezbytné části zkoušení a posouzení.
1.5.2 Zkoušení V rámci
těchto
certifikačních
systémů
je
zkoušení
výrobků
zajišťováno
prostřednictvím zkušebních laboratoří, které splňují všeobecné požadavky ČSN EN ISO/IEC 17025:2005 nebo jiných typů orgánů podle ČSN EN ISO/IEC 17020:2005.
1.5.3 Vzorkování Vzorkování pro zkoušky a šetření se řídí ustanovením příslušné výrobkové normy v souladu se systémem certifikace produktů.
6
Vzorky mají být reprezentativní ve vztahu k celkové řadě nebo skupině produktů, které mají být certifikovány, mají být používány součásti nebo podskupiny totožné s těmi, které jsou používány při produkci a mají být zhotoveny produkčními nástroji a kompletovány s použitím metod zavedených v rámci produkce. Je-li zkoušení založeno na vzorcích prototypu, pak zkoušky shody nebo šetření shody mají být, pokud to připadá v úvahu, prováděny na vzorcích produkce.
1.5.4 Provedení zkoušení Technické prostředky podléhající tomuto certifikačnímu postupu jsou rozděleny podle § 30 zákona č. 412/2005 Sb. Jejich zkoušení je prováděno v souladu se specifikovanou normou (normami) a v souladu se systémem certifikace produktů podle uvedených příloh: j)
mechanické zábranné prostředky – příloha č. 1 (1.1 a 1.2)
k) elektrická zámková zařízení a systémy pro kontrolu vstupů – příloha č. 2 l)
zařízení elektrické zabezpečovací signalizace – příloha č. 3
m) speciální televizní systémy – příloha č. 4 n) tísňové systémy – příloha č. 5 o) zařízení elektrické požární signalizace – příloha č. 6 p) zařízení sloužící k vyhledávání nebezpečných látek nebo předmětů – příloha č. 7 q) zařízení fyzického ničení nosičů informací – příloha č. 8 r) zařízení proti pasivnímu a aktivnímu odposlechu utajované informace - příloha č. 9
1.5.5 Posuzování řízení výroby a systému kvality Posouzení produkčního procesu nebo systému kvality zákazníka je prováděno, ve shodě se systémem certifikace produktů, jako součást přípravy na hodnocení.
1.5.6 Značení výrobků Každý výrobek certifikovaný podle tohoto postupu musí být značen viz příslušná příloha.
1.6 Hodnocení (přezkoumání) Při hodnocení stanovuje certifikační orgán, zda výsledky zkoušení a posouzení produkčního procesu nebo systému kvality splňují specifikované požadavky.
7
1.7 Zpráva o hodnocení – certifikační protokol Kromě požadavků obsažených v kapitole 11 normy ČSN EN 45011:1998, obsahuje Závěrečná zpráva – Certifikační protokol minimálně následující údaje: a) Identifikaci certifikačního orgánu b) Identifikaci objednavatele – zadavatele, identifikaci výrobce certifikovaných výrobků pokud není shodná s objednavatelem – zadavatelem c) Jednoznačnou konkrétní specifikaci certifikovaného výrobku/výrobků, sestávající se z následujících údajů, pokud lze: -
typ, model, řadu, velikosti
-
rozměry
-
provedení, modifikace
-
označení výrobku/výrobků
-
směr otevírání
d) Obecné základní údaje – datum podání přihlášky, žádosti k certifikaci, identifikační číslo zakázky a další údaje podle systému ACO e) Identifikaci certifikačního postupu f) Identifikaci jednotlivých ustanovení normy/norem, podle které je výrobek/jsou výrobky certifikovány g) Identifikaci shromážděných dokumentů a všech dalších významných informací, kterých bylo využito pro rozhodnutí o certifikaci h) Vyhodnocení shora uvedené dokumentace a informací, zejména pak: -
ověření a schválení technické dokumentace – identifikační, základní a specifické
-
vyhodnocení protokolu o zkoušce/zkouškách
i)
Vyhodnocení SJ výrobce – zápis/záznam o výrobkovém auditu
j)
Zjištění a kontrola základních parametrů výrobku/výrobků a řešení požadovaných úkonů – značení atd.
k) Rozšíření na další výrobkové varianty – identifikace variant, modifikací a zdůvodnění l)
Souhrnné zhodnocení zjištěných skutečností
m) Návrh na rozhodnutí n) Datum vydání Závěrečné zprávy – Certifikačního protokolu o) Podpis odpovědné osoby
8
1.7 Rozhodnutí o certifikaci Po dokončení hodnocení (přezkoumání) rozhodne certifikační orgán o shodě. Prohlášení o shodě jako výsledek tohoto rozhodnutí má formu certifikátu, který vyjadřuje ujištění, že specifické požadavky byly splněny.
1.8 Rozšíření rozsahu certifikace Držitel certifikátu, který si přeje rozšířit rozsah certifikace na další druhy nebo modely produktů, na něž se vztahují ty samé specifikované požadavky jako na produkty, na které je již certifikace udělena, požádá certifikační orgán o rozšíření předmětu certifikace. V takových případech certifikační orgán rozhodne, zda ohlášené změny vyžadují další zkoumání. Následně pak může upustit od zkoušení, nebo zkoušení v celém rozsahu, posouzení řízení výroby nebo systému kvality.
1.9 Dozor Certifikační orgán musí vykonávat dozor nad jím certifikovanými produkty na základě požadavků odpovídajících příslušných norem a na základě prvků nebo požadavků schématu certifikace produktů minimálně jedenkrát ročně. Tento dozor zahrnuje i audit řízení výroby
nebo systému kvality na základě požadavků odpovídajících schématu
certifikace produktů. Certifikační orgán může akceptovat existující výsledky posuzování shody, které jsou v souladu se schématem certifikace produktů. Držitel musí informovat certifikační orgán o všech zamýšlených modifikacích produktu, řízení výroby nebo systému kvality, které mohou ovlivnit shodu produktu. Certifikační orgán určí, zda oznámené změny vyžadují zkoušení a posouzení nebo jiná další šetření. V případech, kdy je toto potřeba, nemůže držitel certifikát pro takovéto výrobky používat. Držitel certifikátu musí u výrobků zahrnutých do certifikace udržovat záznamy o všech stížnostech, o jejich vyřizování a tyto záznamy musí na požádání předložit certifikačnímu orgánu k dispozici.
1.10 Použití certifikátu Certifikát vydaný podle tohoto postupu je určen zejména jako součást posudku podle § 46 odst.14 zákona č. 412/2005 Sb. pro žádost o certifikaci technického prostředku v souladu s § 11 vyhlášky č. 528/2005 Sb.
Praha leden 2010
9
Příloha č. 1.1
Příloha č. 1: Mechanické zábranné prostředky - písm. a) § 30 zákona Příloha č. 1.1: Bezpečnostní úschovné objekty a jejich zámky
Bezpečnostní úschovné objekty
Výstup Bezpečnostní třída
Certifikát shody podle certifikačního postupu NBÚ Podle čl. 4.1 a Tabulky 1 a 3 ČSN EN 1143-1:2006
Požadavky pro všechny bezpečnostní třídy Požadavek
Předpis - článek
Skříňové trezory, trezorové dveře a komorové trezory musí ČSN EN 1143-1 splňovat požadavky čl. 4.2.1 až 4.4, Tabulka 1 a Tabulka 3 Zámky, kterými jsou skříňové trezory, trezorové dveře a ČSN EN 1143-1 Tabulka 1 komorové dveře vybaveny musí splňovat požadavky a Tabulka 3 v návaznosti na ČSN EN 1300 Výrobce předloží kompletní technickou dokumentaci ČSN EN 1143-1 kap. 5, čl. 5.1. až 5.8 Výrobce předloží ke zkouškám příslušný počet vzorků – dle ČSN EN 1143-1 kap. 6, dohody s AZL nebo COV čl. 6.1 až 6.3
Požadavky pro zkoušky napadením s využitím nářadí podle ČSN EN 1143-1 Bezpečnostní třídy podle ČSN EN 1143-1 Všechno nářadí používané pro zkoušky musí mít přiřazený koeficient a základní ocenění Nářadí kategorie B zahrnuje nářadí kategorie A Nářadí kategorie C zahrnuje nářadí kategorie A a B Nářadí kategorie D zahrnuje nářadí kategorie A, B a C Nářadí kategorie S zahrnuje nářadí kategorie A, B, C a D Nářadí nesmí být modifikováno, tj. musí být použito pro účely, pro které je konstruováno. Nesmějí být prováděny jiné úpravy nářadí (s výjimkou nářadí povoleného jako „speciálně zhotovené“, není povoleno zvětšovat trysky, prodlužovat elektrody, tyče a páky) Zkušební tělesa pro hodnocení částečného průlomu o délce 150 mm (kruh o průměru 125 mm, čtverec s délkou strany 112 mm, obdélník o délce stran 100 mm x 125 mm) Zkušební tělesa pro hodnocení úplného průlomu o délce 400 mm (kruh o průměru 350 mm, čtverec s délkou strany 315 mm, obdélník o délce stran 300 mm x 330 mm Za úplný průlom se považuje vyjmutí dveří nebo jejich otevření na světlost minimálně 300 mm přes nejméně 80 % vnitřní výšky úschovného prostoru
Podle ČSN EN 1143-1 Příloha A
ČSN EN 1143-1 čl. 7.3.1 a Příloha A
ČSN EN 1143-1 čl. 7.3.1 a Tabulka A.13
ČSN EN 1143-1 čl. 7.3.3
ČSN EN 1143-1 kap. 7.4
Příloha č. 1.1 U mobilních a vestavěných trezorů musí být provedena zkouška napadením s využitím nářadí pro částečný i úplný průlom Skříňové trezory mohou být zkoušeny pouze nářadím kategorie A, B, C a D. Komorové trezory a trezorové dveře mohou být zkoušeny nářadím kategorie A, B, C, D a S V průběhu zkoušky napadením s využitím nářadí nesmí být použito současně nářadí U mobilních skříňových trezorů hmotnosti menší než 1 000 kg musí být provedena zkouška silového namáhání Zkouška vrtání diamantovým korunovým vrtákem stanoví odolnost proti vloupání, při kterém je použito jen diamantové vrtací zařízení – na všech typech pouze pokud si zadavatel přeje používat označení CD Doplňkové požadavky pro označení EX
ČSN EN 1143-1 kap. 7.5 ČSN EN 1143-1 čl. 7.6.5
ČSN EN 1143-1 čl. 7.6.6 ČSN EN 1143-1 Tabulka 1, kap. 8 ČSN EN 1143-1 kap. 10 a Tabulka A.10
ČSN EN 1143-1 Tabulka 1, kap. 9 a Tabulka 4 Hodnota průlomové odolnosti se uvádí v RU jednotkách, ČSN EN 1143-1 kap. 7 výsledek se zaokrouhluje na vyšší celé číslo a čl. 9.6
Požadavky - základní informace, identifikace, použití atd. Požadavek - údaj
Poznámka
- detailní výkresová dokumentace včetně kusovníku - seznam všech dostupných velikostí otvorových výplní odolných proti násilnému vniknutí - definice stran/y napadení - požadovaná bezpečnostní třída + norma - označení výrobku - typ – logo výrobce - všechny dostupné informace o výrobku s ohledem na kování, zámky, těsnění a jiné příslušenství - návod výrobce k montáži
11
Příloha č. 1.1
Trezory se základní bezpečností
Výstup Bezpečnostní třída
Certifikát shody podle certifikačního postupu NBÚ Podle čl. 4.1 a Tabulky 1 ČSN 91 6012:2001
Požadavky pro všechny bezpečnostní třídy Požadavek
Předpis - článek
V ochranném materiálu nesmí existovat žádný otvor, kromě otvorů, které jsou určeny pro zámky, ČSN 91 6012 čl. 4.2 kabely a ukotvení ČSN 91 6012 kap. 4.3 v návaznosti na ČSN EN 1300 kategorie A nebo ČSN EN 1303 do třídy bezpečnosti Zámky, instalované na trezorech se základní související s klíčem 6 a třídy bezpečností musí být certifikovány odolnosti proti napadení 2 nebo ČSN P ENV 1627 do bezpečnostní třídy 4 Pokud nejsou zámky certifikovány platí podmínky ČSN 91 6012 kap. 4.3 a Tabulka 2 Výrobce předloží kompletní technickou ČSN 91 6012 kap. 5, dokumentaci čl. 5.1. až 5.8 Výrobce předloží ke zkouškám příslušný počet ČSN 91 6012 kap. 6, čl. 6.1 až 6.3 vzorků – dle dohody s AZL nebo COV
Požadavky pro zkoušky napadením s využitím nářadí podle ČSN 91 6012 Bezpečnostní třídy podle ČSN 91 6012 Všechno nářadí používané pro zkoušky musí mít přiřazený koeficient a základní ocenění Nářadí kategorie B zahrnuje nářadí kategorie A Nářadí kategorie C zahrnuje nářadí kategorie A a B Nářadí kategorie D zahrnuje nářadí kategorie A, B a C Nářadí kategorie S zahrnuje nářadí kategorie A, B, C a D Nářadí nesmí být modifikováno, tj. musí být použito pro účely, pro které je konstruováno. Nesmějí výt prováděny jiné úpravy nářadí (s výjimkou nářadí povolené jako „speciálně zhotovené“, není povoleno zvětšovat trysky, prodlužovat elektrody, tyče a páky) Zkušební tělesa pro hodnocení částečného průlomu o délce 150 mm (kruh o průměru 125 mm, čtverec s délkou strany 112 mm, obdélník o délce stran 100 mm x 125 mm) Zkušební tělesa pro hodnocení úplného průlomu o délce 400 mm (kruh o průměru 350 mm, čtverec s délkou strany 315 mm, obdélník o délce stran 300 mm x 330 mm
12
podle ČSN EN 1143-1 Příloha A ČSN 91 6012 čl. 7.3.1 a ČSN EN 1143-1 čl. 7.3.1 a Příloha A
ČSN 91 6012 čl. 7.3.1
ČSN 91 6012 čl. 7.3.3
Příloha č. 1.1 Za úplný průlom se považuje vyjmutí dveří nebo jejich otevření na světlost minimálně 300 mm přes nejméně 80 % vnitřní výšky úschovného prostoru a nebo vyjmutí trezoru z modelové stavební konstrukce U mobilních a vestavěných trezorů se základní bezpečností musí být provedena zkouška napadením s využitím nářadí pro částečný i úplný průlom Trezory se základní bezpečností mohou být zkoušeny pouze nářadím kategorie A, B, C a D V průběhu zkoušky napadením s využitím nářadí nesmí být použito současně nářadí U mobilních trezorů se základní bezpečností musí být provedena zkouška pevnosti ukotvení Hodnota průlomové odolnosti se uvádí v RU jednotkách, výsledek se zaokrouhluje na vyšší celé číslo
ČSN 91 6012 kap. 7.4
ČSN 91 6012 kap. 7.5 ČSN 91 6012 kap. 7.6.5 ČSN 91 6012 kap. 7.6.6 ČSN 91 6012 Tabulka 1, kap. 8 ČSN 91 6012 kap. 7.9
Požadavky - základní informace, identifikace, použití atd. Požadavek - údaj
Poznámka
- detailní výkresová dokumentace včetně kusovníku - seznam všech dostupných velikostí otvorových výplní odolných proti násilnému vniknutí - definice stran/y napadení - požadovaná bezpečnostní třída + norma - označení výrobku - typ – logo výrobce - všechny dostupné informace o výrobku s ohledem na kování, zámky, těsnění a jiné příslušenství - návod výrobce k montáži
13
Příloha č. 1.1
Zámky se zvýšenou bezpečností (ZVB)
Výstup Třída bezpečnosti
Certifikát shody podle certifikačního postupu NBÚ Podle kap. 5 a Tabulky 1 ČSN EN 1300:2005
Požadavky pro všechny třídy bezpečnosti Požadavek
Předpis - článek
Jediný platný otevírací kód Je-li pro ZVB použit paměťový kód, musí být možné ho změnit Dodatkové zařízení, kterým je zámek vybaven nesmí umožňovat získání informace o kódu Vstupní jednotka je nezbytnou součástí ZVB a ze vstupní jednotky může být ovládána více než jedna vyhodnocovací jednotka. Každý ZVB musí mít vyhodnocovací jednotku k ověření správnosti kódu ze vstupní jednotky. Každý ZVB musí obsahovat blokovací jednotku, nebo musí být schopen řídit blokovací jednotku. Pokud není blokovací jednotka ovládána ručně, musí zde být prostředky pro indikaci, zda byl zámek uveden do obecného stavu. Bez zadání změnového kódu nesmí být změněn otevírací kód Požadavky na ZVB ve třídě D Požadavky na vlastnosti mechanických klíčových zámků Povolené zdvihové výšky pro mechanické klíčové zámky Požadavky na vlastnosti elektronických ZVB
ČSN EN 1300 čl. 5.1.1.1 ČSN EN 1300 čl. 5.1.1.2 ČSN EN 1300 čl. 5.1.1.3
ČSN EN 1300 čl. 5.1.1.4
ČSN EN 1300 čl. 5.1.1.5 ČSN EN 1300 čl. 5.1.1.6 ČSN EN 1300 čl. 5.1.2 ČSN EN 1300 čl. 5.1.3 ČSN EN 1300 čl. 5.1.4 ČSN EN 1300 čl. 5.1.5
Požadavky na bezpečnost ZVB Požadavek
Předpis - článek
Pro všechny třídy Použitelné kódy ZVB s paralelními zámky
ČSN EN 1300 čl. 5.2 ČSN EN 1300 čl. 5.2.1 ČSN EN 1300 čl. 5.2.2 ČSN EN 1300 čl. 5.2.3 Odolnost proti manipulaci a Tabulka 1 Určení odolnosti oproti manipulaci v závislosti na ČSN EN 1300 Příloha B konstrukčních požadavcích - klíčové zámky čl. B.1 Určení odolnosti oproti manipulaci v závislosti na ČSN EN 1300 Příloha B konstrukčních požadavcích - mechanické kombinační čl. B.2 zámky
14
Příloha č. 1.1 ČSN EN 1300 čl. 5.2.4 a Tabulka 1 + nářadí kategorie A podle ČSN EN 1134-1
Odolnost proti destruktivnímu vloupání
Nářadí nesmí být modifikováno, tj. musí být použito pro účely, pro které je konstruováno. Nesmějí být prováděny ČSN EN 1143-1 čl. 7.3.1 jiné úpravy nářadí (s výjimkou nářadí povoleného jako a Tabulka A.13 „speciálně zhotovené“, není povoleno zvětšovat trysky, prodlužovat elektrody, tyče a páky) Odolnost proti špionáži ČSN EN 1300 čl. 5.2.5 ČSN EN 1300 čl. 5.2.6 Elektrická a elektromagnetická odolnost a Tabulka 2 ČSN EN 1300 čl. 5.2.7 Odolnost proti fyzikálním vlivům prostředí a Tabulka 3 Teplotní odolnost ČSN EN 1300 čl. 5.2.8 ČSN EN 1300 čl. 5.3 Požadavky na spolehlivost (čl. 5.3.1. až čl. 5.3.4) Výrobce předloží kompletní technickou dokumentaci. ČSN EN 1300 kap. 6 Výrobce předloží ke zkouškám příslušný počet vzorků – dle dohody s AZL nebo COV (minimálně čtyři vzorky, v případě, ČSN EN 1300 čl. 7.1 až že má být provedeno zkoušení odolnosti proti manipulaci čl. 7.3 musí dodat další tři vzorky namontované na ocelové zkušební desce). Výpočet hodnoty odolnosti proti manipulaci je uváděn v ČSN EN 1300 čl. 8.2.2.5 odporových jednotkách RU Výpočet hodnoty průlomové odolnosti je uváděn v ČSN EN 1300 čl. 8.2.3.4 odporových jednotkách RU
Požadavky - základní informace, identifikace, použití atd. Požadavek - údaj
Poznámka
- detailní výkresová dokumentace včetně kusovníku - seznam všech dostupných velikostí otvorových výplní odolných proti násilnému vniknutí - definice stran/y napadení - požadovaná bezpečnostní třída + norma - označení výrobku - typ – logo výrobce - všechny dostupné informace o výrobku s ohledem na kování, zámky, těsnění a jiné příslušenství - návod výrobce k montáži
15
Příloha č. 1.2
Příloha č. 1.2: Zabezpečené oblasti a jejich uzamykací systémy
Bezpečnostní otvorové výplně – dveře, okna, mříže apod. Výstup
Certifikát shody podle certifikačního postupu NBÚ
Bezpečnostní třída
Podle čl. 5 a Tabulky 5 ČSN P ENV 1627:2000
Požadavky pro všechny bezpečnostní třídy Požadavek
Předpis - článek
Výrobce předloží ke zkouškám příslušný počet vzorků – dle ČSN P ENV 1627 čl. 6.2 dohody s AZL nebo COV ČSN P ENV 1627 čl. 4.3 Minimální požadavky na skleněnou výplň a Tabulka 1 Odolnost proti statickému zatížení ČSN P ENV 1628 Odolnost proti dynamickému zatížení ČSN P ENV 1629 Odolnost vůči manuálním pokusům o násilné vniknutí ČSN P ENV 1630
Požadavky pro jednotlivé bezpečnostní třídy podle ČSN P ENV 1627 Bezpečnostní třída podle ČSN P ENV 1627
Podmínky zkoušek podle ČSN P ENV 1628, ČSN P ENV 1629, ČSN P ENV 1630 Statické zatížení
Bezpečnostní třída 1
Dynamické zatížení Doba průlomové odolnosti Statické zatížení
Bezpečnostní třída 2
Dynamické zatížení Doba průlomové odolnosti Statické zatížení
Bezpečnostní třída 3
Dynamické zatížení Doba průlomové odolnosti
Podle čl. 6.1 ČSN P ENV 1628 s odkazem na Tabulku 2 a 3 ČSN P ENV 1627 Podle kap. 6 ČSN P ENV 1629 s odkazem na Tabulku 4 ČSN P ENV 1627 Zkouška manuálního pokusu o násilné vniknutí se neprovádí Podle čl. 6.1 ČSN P ENV 1628 s odkazem na Tabulku 2 a 3 ČSN P ENV 1627 Podle kap. 6 ČSN P ENV 1629 s odkazem na Tabulku 4 ČSN P ENV 1627 Podle kap. 6 ČSN P ENV 1630 s odkazem na Tabulku 5 ČSN P ENV 1627 Podle čl. 6.1 ČSN P ENV 1628 s odkazem na Tabulku 2 a 3 ČSN P ENV 1627 Podle kap. 6 ČSN P ENV 1629 s odkazem na Tabulku 4 ČSN P ENV 1627 Podle kap. 6 ČSN P ENV 1630 s odkazem na Tabulku 5 ČSN P ENV 1627
Příloha č. 1.2
Statické zatížení Bezpečnostní třída 4
Dynamické zatížení Doba průlomové odolnosti Statické zatížení
Bezpečnostní třída 5
Dynamické zatížení Doba průlomové odolnosti
Podle čl. 6.1 ČSN P ENV 1628 s odkazem na Tabulku 2 a 3 ČSN P ENV 1627 Podle kap. 6 ČSN P ENV 1629 s odkazem na Tabulku 4 ČSN P ENV 1627 Podle kap. 6 ČSN P ENV 1630 s odkazem na Tabulku 5 ČSN P ENV 1627 Podle čl. 6.1 ČSN P ENV 1628 s odkazem na Tabulku 2 a 3 ČSN P ENV 1627 Podle kap. 6 ČSN P ENV 1629 s odkazem na Tabulku 4 ČSN P ENV 1627 Podle kap. 6 ČSN P ENV 1630 s odkazem na Tabulku 5 ČSN P ENV 1627
Požadavky pro jednotlivé bezpečnostní třídy podle ČSN P ENV 1627 Základní požadavky pro jednotlivé bezpečnostní třídy jsou uvedeny v tabulce č. 5 shora uvedené normy – doba průlomové odolnosti a celkový čas zkoušky. Zkouška – zkoušky jsou prováděny podle ČSN P ENV 1630.
Bezpečnostní třída podle ČSN P ENV 1627 Bezpečnostní třída 1 Bezpečnostní třída 2
Bezpečnostní třída 3
Bezpečnostní třída 4
Bezpečnostní třída 5
Aplikace nářadí v příslušné době průlomové odolnosti Bez aplikace Nářadí kategorie A + dodatečné nářadí (kroucení tělesa vložky - picking, páčení kování a páčení dveřního křídla) Nářadí kategorie A+B + dodatečné nářadí (kroucení tělesa vložky - picking, páčení kování a páčení dveřního křídla) Nářadí kategorie A+B+C + dodatečné nářadí (kroucení tělesa vložky - picking, páčení kování a páčení dveřního křídla sekání - vrtání) Nářadí kategorie A+B+C+D + dodatečné nářadí (kroucení tělesa vložky - picking, páčení kování a páčení dveřního křídla, páčení dveřního křídla - sekání - vrtání řezání)
17
Doba průlomové odolnosti Nezkouší se 3 min
5 min
10 min
15 min
Příloha č. 1.2
Požadavky - základní informace, identifikace, použití atd. Požadavek - údaj
Poznámka
- detailní výkresová dokumentace včetně kusovníku - seznam všech dostupných velikostí otvorových výplní odolných proti násilnému vniknutí - definice stran/y napadení - požadovaná bezpečnostní třída + norma - označení výrobku - typ – logo výrobce - všechny dostupné informace o výrobku s ohledem na kování, zámky, těsnění a jiné příslušenství - návod výrobce k montáži NBÚ nebude certifikovat samostatně bezpečnostní sklo.
18
Příloha č. 1.2
Cylindrické vložky – mechanické
Výstup Třída bezpečnosti související s klíčem (TB) Třída odolnosti proti napadení (TO) Bezpečnostní třída (BT) Bezpečnostní třída odolnosti proti bumpingu (BT)
Certifikát shody podle certifikačního postupu NBÚ podle článku 4.8 a Tabulky 9 ČSN EN 1303:2005 podle článku 4.9 a Tabulky 10 ČSN EN 1303:2005 podle kapitoly 5 a Tabulky 5 ČSN P ENV 1627:2000 Podle přílohy certifikačního postupu NBÚ (Metodika zkoušení cylindrických vložek nedestruktivní metodou bumpingu)
Požadavky pro všechny bezpečnostní třídy Požadavek
Předpis - článek
Výrobce předloží ke zkouškám klasifikační tabulku Pevnost klíče Životnost (pro třídy bezpečnosti související s klíčem 4 - 5 - 6 Minimální počet efektivních kombinací Minimální počet pohyblivých stavítek Maximální počet zářezů stejné hloubky Značení zářezů na klíči Ovládání bezpečnostního mechanismu Odolnost cylindrické vložky a/ nebo válce v krutu Odolnost proti napadení vrtáním Odolnost proti napadení sekáčem Odolnost proti napadení krutem Odolnost proti napadení vytržením cylindrické vložky a/ nebo válce Počet vzorků na zkoušky – 13 kusů Technická dokumentace výrobku Výrobce předloží ke zkouškám příslušný počet vzorků – dle dohody s AZL nebo COV – minimálně 2 kusy Počet vzorků na zkoušky odolnosti proti dumpingu 22 kusů vložek a 35 kusů polotovarů klíčů Technická dokumentace výrobku v rozsahu uvedeném v Metodika zkoušení cylindrických vložek nedestruktivní metodou bumpingu
19
ČSN EN 1303 čl. 6.1 ČSN EN 1303 čl. 4.2 ČSN EN 1303 čl. 4.3 ČSN EN 1303 čl. 4.8.2 ČSN EN 1303 čl. 4.8.3 ČSN EN 1303 čl. 4.8.4 ČSN EN 1303 čl. 4.8.5 ČSN EN 1303 čl. 4.8.6 ČSN EN 1303 čl. 4.8.7 ČSN EN 1303 čl. 4.9.1 ČSN EN 1303 čl. 4.9.2 ČSN EN 1303 čl. 4.9.3 ČSN EN 1303 čl. 4.9.4 ČSN EN 1303 Příloha D ČSN P ENV 1627 čl. 6.2 a ČSN P ENV 1630 kapitola 6 Podle přílohy certifikačního postupu NBÚ (Metodika zkoušení cylindrických vložek nedestruktivní metodou bumpingu)
Příloha č. 1.2
Požadavky pro jednotlivé bezpečnostní třídy podle ČSN P ENV 1627 v návaznosti na ČSN EN 1303 Bezpečnostní třída podle ČSN P ENV 1627
Třída bezpečnosti související s klíčem/Třída odolnosti proti napadení podle ČSN EN 1303 TB 4 / TO 0 TB 4 / TO 1 TB 4 / TO 1 TB 6 / TO 2 TB 6 / TO 2
Bezpečnostní třída 1 Bezpečnostní třída 2 Bezpečnostní třída 3 Bezpečnostní třída 4 Bezpečnostní třída 5
Požadavky pro jednotlivé bezpečnostní třídy podle ČSN P ENV 1627 Základní požadavky pro jednotlivé bezpečnostní třídy jsou uvedeny v tabulce č. 5 shora uvedené normy – doba průlomové odolnosti a celkový čas zkoušky. Zkouška – zkoušky jsou prováděny podle ČSN P ENV 1630. Bezpečnostní třída podle ČSN P ENV 1627
Aplikace nářadí v příslušné době průlomové odolnosti
Bezpečnostní třída 1
Bez aplikace Nářadí kategorie A + dodatečné nářadí (ukroucení tělesa – picking ) Nářadí kategorie A+B + dodatečné nářadí (ukroucení tělesa – picking ) Nářadí kategorie A+B+C + dodatečné nářadí (ukroucení tělesa – picking odseknutí – odvrtání) Nářadí kategorie A+B+C+D + dodatečné nářadí (ukroucení tělesa – picking odseknutí – odvrtání – odříznutí)
Bezpečnostní třída 2 Bezpečnostní třída 3 Bezpečnostní třída 4
Bezpečnostní třída 5
Doba průlomové odolnosti Nezkouší se 3 min 5 min 10 min
15 min
Požadavky - základní informace, identifikace, použití atd. Požadavek - údaj
Poznámka
- logo výrobce - označení výrobku – typ – bezpečnostní třída + norma - odolnost proti metodě bumpingu - kontrola počtu efektivních kombinací – prohlášení výrobce - kontrola omezujících parametrů – připojovací rozměry, kombinace provedení, modifikace, atd. - speciální operace – záznamy - značení klíče – bezpečnostní karta - výroba náhradních klíčů - konstrukční údaje – tvar otvoru pro klíč – počet a tvar stavítek
20
Příloha č. 1.2 - další označení, údaje dle výrobce, kód podle EN 1303 atd.
Cylindrické vložky – mechatronické
Výstup Certifikát shody podle certifikačního postupu NBÚ Třída bezpečnosti související s klíčem podle článku 4.8 prEN 15684:2007 (TB) Třída odolnosti proti napadení (TO) podle článku 4.10 prEN 15684:2007 a podle článku 4.9 ČSN EN 1303:2005 Bezpečnostní třída (BT) podle kapitoly 5 a Tabulky ČSN P ENV 1627:2000 Bezpečnostní třída odolnosti proti Podle přílohy certifikačního postupu NBÚ bumpingu (BT) (Metodika zkoušení cylindrických vložek nedestruktivní metodou bumpingu)
Požadavky pro všechny bezpečnostní třídy Požadavek Výrobce předloží ke zkouškám klasifikační tabulku Pevnost klíče Stabilita elektronického klíče Chybný elektronický kód Úder a vibrační požadavky Požadavek elektrostatického výboje Životnost (pro třídy bezpečnosti související s klíčem 4-5–6) Odolnost vůči prostředí Minimální počet mechanických kódových kombinací Odolnost cylindrické vložky a/ nebo válce v krutu Minimální počet elektronických kódových kombinací Řízení systému Odolnost proti mechanickým útokům Počet vzorků na zkoušky – 10 kusů + 13 kusů Technická dokumentace výrobku Výrobce předloží ke zkouškám příslušný počet vzorků – dle dohody s AZL nebo COV – minimálně 2 kusy Počet vzorků na zkoušky odolnosti proti bumpingu 22 kusů vložek a 35 kusů polotovarů klíčů Technická dokumentace výrobku v rozsahu uvedeném v Metodika zkoušení cylindrických vložek nedestruktivní metodou bumpingu
21
Předpis - článek prEN 15684 kapitola 7 prEN 15684 čl. 4.2.1 prEN 15684 čl. 4.2.2 prEN 15684 čl. 4.2.3 prEN 15684 čl. 4.2.4 prEN 15684 čl. 4.2.5 prEN 15684 čl. 4.3 a ČSN EN 1303 čl. 4.3 prEN 15684 čl. 4.7.1 - 4.7.6 prEN 15684 čl. 4.8.1 prEN 15684 čl. 4.8.2 a ČSN EN 1303 čl. 4.8.7 prEN 15684 čl. 4.8.3 prEN 15684 čl. 4.9 prEN 15684 čl. 4.10.2 -4.10.7 a ČSN EN 1303 čl. 4.9.1 – 4.9.5 prEN 15684 Příloha C a ČSN EN 1303 Příloha D ČSN P ENV 1627 čl. 6.2 a ČSN P ENV 1630 kapitola 6 Podle přílohy certifikačního postupu NBÚ (Metodika zkoušení cylindrických vložek nedestruktivní metodou bumpingu)
Příloha č. 1.2
Požadavky pro jednotlivé bezpečnostní třídy podle ČSN P ENV 1627 v návaznosti na prEN 15684
Bezpečnostní třída 1
Třída bezpečnosti související s klíčem/Třída odolnosti proti napadení podle prEN 15684 a podle ČSN EN 1303 TB 4/D / TO 0
Bezpečnostní třída 2
TB 4/D / TO 1
Bezpečnostní třída 3
TB 4/D / TO 1
Bezpečnostní třída 4
TB 6/E / TO 2
Bezpečnostní třída 5
TB 6/F / TO 2
Bezpečnostní třída podle ČSN P ENV 1627
Požadavky pro jednotlivé bezpečnostní třídy podle ČSN P ENV 1627 Základní požadavky pro jednotlivé bezpečnostní třídy jsou uvedeny v tabulce č. 5 shora uvedené normy – doba průlomové odolnosti a celkový čas zkoušky. Zkouška – zkoušky jsou prováděny podle ČSN P ENV 1630.
Bezpečnostní třída podle ČSN P ENV 1627
Aplikace nářadí v příslušné době průlomové odolnosti
Bezpečnostní třída 1
Bez aplikace Nářadí kategorie A + dodatečné nářadí (ukroucení tělesa – picking ) Nářadí kategorie A+B + dodatečné nářadí (ukroucení tělesa – picking ) Nářadí kategorie A+B+C + dodatečné nářadí (ukroucení tělesa – picking odseknutí – odvrtání) Nářadí kategorie A+B+C+D + dodatečné nářadí (ukroucení tělesa – picking odseknutí – odvrtání – odříznutí)
Bezpečnostní třída 2 Bezpečnostní třída 3 Bezpečnostní třída 4
Bezpečnostní třída 5
Doba průlomové odolnosti Nezkouší se 3 min 5 min 10 min
15 min
Požadavky na základní parametry – údaje, identifikace, použití atd. Požadavek - údaj
Poznámka
- logo výrobce - označení výrobku – typ – bezpečnostní třída + norma - odolnost proti metodě bumpingu - kontrola počtu efektivních kombinací – prohlášení výrobce - kontrola omezujících parametrů – připojovací rozměry, kombinace provedení, modifikace, atd. - speciální operace – záznamy - značení klíče – bezpečnostní karta - výroba náhradních klíčů - konstrukční údaje – tvar otvoru pro klíč – počet a tvar stavítek
22
Příloha č. 1.2 - další označení, údaje dle výrobce, kód podle prEN 15684 atd.
Zámky a střelkové zámky a zapadací plechy - elektromechanicky ovládané
Výstup Třída bezpečnosti (TB) Třída bezpečnosti – elektrická funkce (TB-F) Třída bezpečnosti – elektrická manipulace (TB-M) Bezpečnostní třída (BT)
Certifikát shody podle certifikačního postupu NBÚ podle článku 4.9 ČSN EN 14846:2009 a podle článku 4.2.7 a Tabulka 5 ČSN EN 12209:2004 podle článku 4.10 ČSN EN 14846:2009 podle článku 4.11 ČSN EN 14846:2009 podle kapitoly 5 a Tabulky ČSN P ENV 1627:2000
Požadavky pro všechny bezpečnostní třídy Požadavek
Předpis - článek
Výrobce předloží ke zkouškám klasifikační tabulku Zaměnitelnost spolupůsobících částí Nebezpečné látky Odolnost proti korozi, teplotě a vlhkosti Odolnost knoflíku v krutu Požadavky na boční zatížení Průmět neodpružené závory Požadavky na čelní zatížení neodpružené závory Odolnost proti vytažení hákové závory/rozevírací závory Odolnost proti zdvižení hákové závory/rozevírací závory Odolnost proti útoku na zamykací zařízení v posuvných dveřích Odolnost proti vytržení knoflíku sady střelky a sady střelkového zámku určeného k zavrtání Bezpečnostní požadavky na součásti zapadacího plechu Bezpečnost – elektrická funkce – ukazatel stavu Bezpečnost – elektrická manipulace Požadavky na informace o výrobku Počet vzorků na zkoušky – 2 kusy pro každou zkoušku + 6 kusů Technická dokumentace výrobku Výrobce předloží ke zkouškám příslušný počet vzorků – dle dohody s AZL nebo COV – minimálně 2 kusy
23
ČSN EN 14846 čl. 4.2 ČSN EN 14846 čl. 5.1.1 ČSN EN 14846 čl. 5.1.2 ČSN EN 14846 čl. 5.7 ČSN EN 14846 čl. 5.8 a ČSN EN 12209 čl. 5.8.1. ČSN EN 14846 čl. 5.8 a ČSN EN 12209 čl. 5.8.2 ČSN EN 14846 čl. 5.8 a ČSN EN 12209 čl. 5.8.3 ČSN EN 14846 čl. 5.8 a ČSN EN 12209 čl. 5.8.4 ČSN EN 14846 čl. 5.8 a ČSN EN 12209 čl. 5.8.5 ČSN EN 14846 čl. 5.8 a ČSN EN 12209 čl. 5.8.6 ČSN EN 14846 čl. 5.8 a ČSN EN 12209 čl. 5.8.7 ČSN EN 14846 čl. 5.8 a ČSN EN 12209 čl. 5.8.8 ČSN EN 14846 čl. 5.8 a ČSN EN 12209 čl. 5.8.9 ČSN EN 14846 čl. 5.9 ČSN EN 14846 čl. 5.10 ČSN EN 14846 čl. 5.11 ČSN EN 14846 Příloha B a ČSN EN 12209 Příloha C ČSN EN 14846 Příloha B ČSN P ENV 1627 čl. 6.2 a ČSN P ENV 1630 kapitola 6
Příloha č. 1.2
Požadavky pro jednotlivé bezpečnostní třídy podle ČSN P ENV 1627 v návaznosti na ČSN EN 14846 Bezpečnostní třída podle ČSN P ENV 1627 Bezpečnostní třída 1
Třída bezpečnosti související s klíčem/Třída odolnosti proti napadení podle ČSN EN 14846 TB 3 / TB-F 1 / TB-M 0
Bezpečnostní třída 2
TB 3 / TB-F 1 / TB-M 1
Bezpečnostní třída 3
TB 4 / TB-F 1 / TB-M 2
Bezpečnostní třída 4
TB 7 / TB-F 1 / TB-M 3
Bezpečnostní třída 5
TB 7 / TB-F 1 / TB-M 3
Požadavky pro jednotlivé bezpečnostní třídy podle ČSN P ENV 1627 Základní požadavky pro jednotlivé bezpečnostní třídy jsou uvedeny v tabulce č. 5 shora uvedené normy – doba průlomové odolnosti a celkový čas zkoušky. Zkouška – zkoušky jsou prováděny podle ČSN P ENV 1630 Bezpečnostní třída podle ČSN P ENV 1627 Bezpečnostní třída 1 Bezpečnostní třída 2 Bezpečnostní třída 3 Bezpečnostní třída 4 Bezpečnostní třída 5
Aplikace nářadí v příslušné době průlomové odolnosti Bez aplikace Nářadí kategorie A + dodatečné nářadí (páčení ) Nářadí kategorie A+B + dodatečné nářadí (páčení ) Nářadí kategorie A+B+C + dodatečné nářadí (páčení - sekání – vrtání) Nářadí kategorie A+B+C+D + dodatečné nářadí (páčení - sekání - vrtání - řezání)
Doba průlomové odolnosti Nezkouší se 3 min 5 min 10 min 15 min
Požadavky - základní informace, identifikace, použití atd. Požadavek - údaj
Poznámka
- logo výrobce - označení výrobku – typ – kategorie použití - bezpečnostní třídy + norma - kontrola omezujících parametrů – připojovací rozměry, kombinace provedení, modifikace, atd. - speciální operace – záznamy - konstrukční údaje – velikost čtyřhranu kliky, - další označení, údaje dle výrobce, kód podle ČSN EN 14846 atd.
24
Příloha č. 1.2
Zámky a střelkové zámky a zapadací plechy - mechanicky ovládané
Výstup Třída bezpečnosti (TB) Bezpečnostní třída (BT)
Certifikát shody podle certifikačního postupu NBÚ podle článku 5.8 a Tabulky 5 ČSN EN 12209:2004 podle kapitoly 5 a Tabulky ČSN P ENV 1627:2000
Požadavky pro všechny bezpečnostní třídy Požadavek
Předpis - článek
Výrobce předloží ke zkouškám klasifikační tabulku Nebezpečné látky Vratná síla střelky Odolnost knoflíku v krutu Požadavky pro boční zatížení Průmět neodpružené závory Požadavky na čelní zatížení neodpružené závory Odolnost proti vytažení hákové závory/rozevírací závory Odolnost proti zdvižení hákové závory/rozevírací závory Odolnost proti útoku na zamykací zařízení v posuvných dveřích Odolnost proti vytržení knoflíku sady střelky a sady střelkového zámku určeného k zavrtání Bezpečnostní požadavky na součásti zapadacího plechu Počet vzorků na zkoušky – 2 kusy pro každou zkoušku Technická dokumentace výrobku Výrobce předloží ke zkouškám příslušný počet vzorků – dle dohody s AZL nebo COV – minimálně 2 kusy
ČSN EN 12209 čl. 4.2 ČSN EN 12209 čl. 5.1.1 ČSN EN 12209 čl. 5.1.2 ČSN EN 12209 čl. 5.8.1. ČSN EN 12209 čl. 5.8.2 ČSN EN 12209 čl. 5.8.3 ČSN EN 12209 čl. 5.8.4 ČSN EN 12209 čl. 5.8.5 ČSN EN 12209 čl. 5.8.6 ČSN EN 12209 čl. 5.8.7 ČSN EN 12209 čl. 5.8.8 ČSN EN 12209 čl. 5.8.9 ČSN EN 12209 Příloha C ČSN P ENV 1627 čl. 6.2 a ČSN P ENV 1630 kapitola 5
Požadavky pro jednotlivé bezpečnostní třídy podle ČSN P ENV 1627 v návaznosti na ČSN EN 12209
Bezpečnostní třída 1
Třída bezpečnosti související s klíčem/Třída odolnosti proti napadení podle ČSN EN 12209 TB 3
Bezpečnostní třída 2
TB 3
Bezpečnostní třída 3
TB 4
Bezpečnostní třída 4
TB 7
Bezpečnostní třída 5
TB 7
Bezpečnostní třída podle ČSN P ENV 1627
25
Příloha č. 1.2
Požadavky pro jednotlivé bezpečnostní třídy podle ČSN P ENV 1627 Základní požadavky pro jednotlivé bezpečnostní třídy jsou uvedeny v tabulce č. 5 shora uvedené normy – doba průlomové odolnosti a celkový čas zkoušky. Zkouška – zkoušky jsou prováděny podle ČSN P ENV 1630
Bezpečnostní třída podle ČSN P ENV 1627 Bezpečnostní třída 1 Bezpečnostní třída 2 Bezpečnostní třída 3 Bezpečnostní třída 4 Bezpečnostní třída 5
Aplikace nářadí v příslušné době průlomové odolnosti Bez aplikace
Doba průlomové odolnosti Nezkouší se
Nářadí kategorie A + dodatečné nářadí (páčení ) Nářadí kategorie A+B + dodatečné nářadí (páčení) Nářadí kategorie A+B+C + dodatečné nářadí (páčení - sekání – vrtání) Nářadí kategorie A+B+C+D + dodatečné nářadí (páčení - sekání vrtání - řezání)
3 min 5 min 10 min 15 min
Požadavky - základní informace, identifikace, použití atd. Požadavek - údaj
Poznámka
- logo výrobce - označení výrobku – typ – kategorie použití - bezpečnostní třída + norma - kontrola počtu efektivních kombinací – prohlášení výrobce -
kontrola omezujících parametrů – kombinace provedení, modifikace, atd. - speciální operace – záznamy
připojovací
rozměry,
- konstrukční údaje – velikost čtyřhranu kliky, - další označení, údaje dle výrobce, kód podle ČSN EN 12209 atd.
26
Příloha č. 1.2
Zámky a střelkové zámky a zapadací plechy - vícebodové zámky a zapadací plechy
Výstup Třída bezpečnosti (TB) Bezpečnostní třída (BT)
Certifikát shody podle certifikačního postupu NBÚ podle článku 5.8 a Tabulky 7 prEN 15685:2007 podle kapitoly 5 a Tabulky ČSN P ENV 1627:2000
Požadavky pro všechny bezpečnostní třídy Požadavek
Předpis - článek
Výrobce předloží ke zkouškám klasifikační tabulku
prEN 15685 čl. 4.2
Nebezpečné látky
prEN 15685 čl. 5.1.1
Vratná síla střelky
prEN 15685 čl. 5.1.2
Odolnost uzamykatelného ořechu zámku v krutu
prEN 15685 čl. 5.8.1.
Požadavky na boční zatížení
prEN 15685 čl. 5.8.2
Průmět závory uzamykacího bodu
prEN 15685 čl. 5.8.3
Požadavky na čelní zatížení na uzamykací bod
prEN 15685 čl. 5.8.4
Bezpečnostní požadavky na zapadací plech
prEN 15685 čl. 5.8.5
Požadavky na konstrukci stavítkových zámků
prEN 15685 čl. 5.12
Požadavky na protiseparační ochranu
prEN 15685 čl. 5.13
Počet vzorků na zkoušky – 2 kusy pro každou zkoušku
prEN 15685 Příloha C
Technická dokumentace výrobku Výrobce předloží ke zkouškám příslušný počet vzorků – dle dohody s AZL nebo COV – minimálně 2 kusy
prEN 15685 Příloha C ČSN P ENV 1627 čl. 6.2 a ČSN P ENV 1630 kapitola 6
Požadavky pro jednotlivé bezpečnostní třídy podle ČSN P ENV 1627 v návaznosti na prEN 15685 Bezpečnostní třída podle ČSN P ENV 1627 Bezpečnostní třída 1
Třída bezpečnosti podle prEN 15685 TB 3
Bezpečnostní třída 2
TB 3
Bezpečnostní třída 3
TB 4
Bezpečnostní třída 4
TB 7
Bezpečnostní třída 5
TB 7
27
Příloha č. 1.2
Požadavky pro jednotlivé bezpečnostní třídy podle ČSN P ENV 1627 Základní požadavky pro jednotlivé bezpečnostní třídy jsou uvedeny v tabulce č. 5 shora uvedené normy – doba průlomové odolnosti a celkový čas zkoušky. Zkouška – zkoušky jsou prováděny podle ČSN P ENV 1630. Bezpečnostní třída podle ČSN P ENV 1627 Bezpečnostní třída 1 Bezpečnostní třída 2 Bezpečnostní třída 3 Bezpečnostní třída 4 Bezpečnostní třída 5
Aplikace nářadí v příslušné době průlomové odolnosti Bez aplikace
Doba průlomové odolnosti Nezkouší se
Nářadí kategorie A + dodatečné nářadí (páčení ) Nářadí kategorie A+B + dodatečné nářadí (páčení) Nářadí kategorie A+B+C + dodatečné nářadí (páčení - sekání – vrtání) Nářadí kategorie A+B+C+D + dodatečné nářadí (páčení - sekání vrtání - řezání)
3 min 5 min 10 min 15 min
Požadavky - základní informace, identifikace, použití atd. Požadavek - údaj
Poznámka
- logo výrobce - označení výrobku – typ – kategorie použití - bezpečnostní třída + norma - kontrola počtu efektivních kombinací – prohlášení výrobce - kontrola omezujících parametrů – připojovací rozměry, kombinace provedení, modifikace, atd. - speciální operace – záznamy - konstrukční údaje – velikost čtyřhranu kliky, počet stavítek - další označení, údaje dle výrobce, kód podle prEN 15685 atd.
28
Příloha č. 1.2
Dveřní štíty, kliky a knoflíky
Výstup Třída bezpečnosti (TB) Bezpečnostní třída (BT)
Certifikát shody podle certifikačního postupu NBÚ podle Přílohy A a Tabulky A.1 ČSN EN 1906:2003 podle kapitoly 5 a Tabulky 5 ČSN P ENV 1627:2000
Požadavky pro všechny bezpečnostní třídy Požadavek
Předpis - článek
Výrobce předloží ke zkouškám klasifikační tabulku
ČSN EN 1906 čl. 4.2
Požadavky na provedení
ČSN EN 1906 čl. A.2.1
Pevnost štítu
ČSN EN 1906 čl. A.2.2.1
Pevnost připevňovacích prvků
ČSN EN 1906 čl. A.2.2.2
Odolnost proti napadení vrtáním
ČSN EN 1906 čl. A.2.2.3
Odolnost proti útoku sekáčem
ČSN EN 1906 čl. A.2.2.4
Pevnost krytu cylindrické vložky
ČSN EN 1906 čl. A.2.2.5
Počet vzorků na zkoušky – 5 kusů ČSN EN 1906 Příloha A Výrobce předloží ke zkouškám příslušný počet vzorků – ČSN P ENV 1627 čl. 6.2 a dle dohody s AZL nebo COV – minimálně 2 kusy ČSN P ENV 1630 kapitola 6
Požadavky pro jednotlivé bezpečnostní třídy podle ČSN P ENV 1627 v návaznosti na ČSN EN 1906 Bezpečnostní třída podle ČSN P ENV 1627 Bezpečnostní třída 1
Třída bezpečnosti podle ČSN EN 1906 TB 1
Bezpečnostní třída 2
TB 2
Bezpečnostní třída 3
TB 3
Bezpečnostní třída 4
TB 4
Bezpečnostní třída 5
TB 4
29
Příloha č. 1.2
Požadavky pro jednotlivé bezpečnostní třídy podle ČSN P ENV 1627 Základní požadavky pro jednotlivé bezpečnostní třídy jsou uvedeny v tabulce č. 5 shora uvedené normy – doba průlomové odolnosti a celkový čas zkoušky. Zkouška – zkoušky jsou prováděny podle ČSN P ENV 1630. Bezpečnostní třída podle ČSN P ENV 1627 Bezpečnostní třída 1 Bezpečnostní třída 2 Bezpečnostní třída 3 Bezpečnostní třída 4 Bezpečnostní třída 5
Aplikace nářadí v příslušné době průlomové odolnosti Bez aplikace
Doba průlomové odolnosti Nezkouší se
Nářadí kategorie A + dodatečné nářadí (páčení tělesa a krytu ) Nářadí kategorie A+B + dodatečné nářadí (páčení tělesa a krytu) Nářadí kategorie A+B+C + dodatečné nářadí (páčení tělesa a krytu - odseknutí – odvrtání) Nářadí kategorie A+B+C+D + dodatečné nářadí (páčení tělesa a krytu - odseknutí – odvrtání – odříznutí)
3 min 5 min 10 min 15 min
Požadavky - základní informace, identifikace, použití atd. Požadavek - údaj
Poznámka
- logo výrobce - označení výrobku – typ – bezpečnostní třída + norma -
kontrola omezujících parametrů – kombinace provedení, modifikace, atd. - speciální operace – záznamy
připojovací
rozměry,
- konstrukční údaje – tvar, velikost a tvrdost ochranných prvků - další označení, údaje dle výrobce, kód podle ČSN EN1906 atd.
30
Příloha č. 1.2
Jednoosé závěsy
Výstup Třída bezpečnosti (TB) Bezpečnostní třída (BT)
Certifikát shody podle certifikačního postupu NBÚ podle článku 4.8 a Tabulky 2 ČSN EN 1935:2002 podle kapitoly 5 a Tabulky ČSN P ENV 1627:2000
Požadavky pro všechny bezpečnostní třídy Požadavek
Předpis - článek
Výrobce předloží ke zkouškám klasifikační tabulku
ČSN EN 1935 čl. 4.10
Počáteční měření třecího momentu
ČSN EN 1935 čl. 5.1
Statické zatížení
ČSN EN 1935 čl. 5.2
Pevnost ve střihu
ČSN EN 1935 čl. 5.3
Životnost
ČSN EN 1935 čl. 5.4
Odolnost proti korozi Závěsy pro použití na protipožárních/protikouřových dveřních sestavách
ČSN EN 1935 čl. 5.5 ČSN EN 1935 čl. 5.6
Závěsy pro použití na dveřích odolných proti vloupání
Skupiny závěsů se stejnými konstrukčními znaky Počet vzorků na zkoušky – 12 kusů závěsů Výrobce předloží ke zkouškám příslušný počet vzorků – dle dohody s AZL nebo COV – minimálně 2 soupravy závěsů
ČSN EN 1935 čl. 5.7 a příloha C ČSN EN 1935 čl. 5.8 ČSN EN 1935 čl. 5.1 ČSN EN 1935 čl. 5.1 ČSN EN 1935 čl. 5.1 ČSN EN 1935 čl. 7.1.1 ČSN P ENV 1627 čl. 6.2 a ČSN P ENV 1630 kapitola 6
Požadavky pro jednotlivé bezpečnostní třídy podle ČSN P ENV 1627 v návaznosti na ČSN EN 1935 Bezpečnostní třída podle ČSN P ENV 1627 Bezpečnostní třída 1
Třída bezpečnosti podle ČSN EN 1935 TB 1
Bezpečnostní třída 2
TB 1
Bezpečnostní třída 3
TB 1
Bezpečnostní třída 4
TB 1
Bezpečnostní třída 5
TB 1
31
Příloha č. 1.2
Požadavky pro jednotlivé bezpečnostní třídy podle ČSN P ENV 1627 Základní požadavky pro jednotlivé bezpečnostní třídy jsou uvedeny v tabulce č. 5 shora uvedené normy – doba průlomové odolnosti a celkový čas zkoušky. Zkouška – zkoušky jsou prováděny podle ČSN P ENV 1630 Bezpečnostní třída podle ČSN P ENV 1627 Bezpečnostní třída 1 Bezpečnostní třída 2 Bezpečnostní třída 3 Bezpečnostní třída 4 Bezpečnostní třída 5
Aplikace nářadí v příslušné době průlomové odolnosti Bez aplikace Nářadí kategorie A + dodatečné nářadí (páčení ) Nářadí kategorie A+B + dodatečné nářadí (páčení ) Nářadí kategorie A+B+C + dodatečné nářadí (páčení - odseknutí – odvrtání) Nářadí kategorie A+B+C+D + dodatečné nářadí (páčení - odseknutí – odvrtání – odříznutí)
Doba průlomové odolnosti Nezkouší se 3 min 5 min 10 min 15 min
Požadavky - základní informace, identifikace, použití atd. Požadavek - údaj
Poznámka
- logo výrobce - označení výrobku – typ – bezpečnostní třída + norma - kontrola omezujících parametrů – připojovací rozměry, kombinace provedení, modifikace, typická použití atd. - speciální operace – záznamy - další označení, údaje dle výrobce, kód podle ČSN EN 1935 atd.
32
Příloha č. 1.2
Visací zámky a příslušenství visacích zámků
Výstup
Certifikát shody podle certifikačního postupu NBÚ
Třída bezpečnosti (TB)
podle článku 4.3 a Tabulka 2 ČSN EN 12320:2002
Bezpečnostní třída (BT)
podle kapitoly 5 a Tabulky 5 ČSN P ENV 1627:2000 Podle přílohy certifikačního postupu NBÚ (Metodika zkoušení cylindrických vložek nedestruktivní metodou bumpingu (a visacích zámků opatřených cylindrickou vložkou nebo obdobným systémem)
Bezpečnostní třída odolnosti proti bumpingu (BT)
Požadavky pro všechny bezpečnostní třídy Požadavek
Předpis - článek
Výrobce předloží ke zkouškám klasifikační tabulku Odolnost proti korozi Minimální počet efektivních kombinací
ČSN EN 12320 čl. 6.1 ČSN EN 12320 čl. 4.2 a EN 1670 ČSN EN 12320 čl. 4.3.1
Ovládání bezpečnostního mechanismu ČSN EN 12320 čl. 4.3.2 Odolnost válcové vložky nebo uzamykacího mechanismu ČSN EN 12320 čl. 4.3.3 proti vytržení Odolnost válcové vložky nebo uzamykacího mechanismu ČSN EN 12320 čl. 4.3.4 visacího zámku v krutu Odolnost třmenu a oka petlice proti vytržení ČSN EN 12320čl. 4.3.5 Odolnost třmenu a oka petlice proti krutu
ČSN EN 12320 čl. 4.3.6
Odolnost třmenu a oka petlice proti přestřižení Odolnost tělesa visacího zámku, třmenu a oka petlice proti nárazu při nízké teplotě Odolnost tělesa visacího zámku, třmenu a oka petlice proti odvrtání Odolnost tělesa visacího zámku, třmenu a oka petlice proti řezání Počet vzorků na zkoušky – 12 kusů visacích zámků 6 kusů petlic Výrobce předloží ke zkouškám příslušný počet vzorků – dle dohody s AZL nebo COV – minimálně 2 vzorků visacích zámků – 2 kusy petlic Počet vzorků na zkoušky odolnosti proti bumpingu 22 kusů vložek a 35 kusů polotovarů klíčů Technická dokumentace výrobku v rozsahu uvedeném v Metodika zkoušení cylindrických vložek nedestruktivní metodou bumpingu
ČSN EN 12320 čl. 4.3.7
33
ČSN EN 12320 čl. 4.3.8 ČSN EN 12320 čl. 4.3.9 ČSN EN 12320 čl. 4.3.10 ČSN EN 12320 Příloha A ČSN P ENV 1627 čl. 6.2 a ČSN P ENV 1630 kapitola 6 Podle přílohy certifikačního postupu NBÚ (Metodika zkoušení cylindrických vložek nedestruktivní metodou bumpingu)
Příloha č. 1.2
Požadavky pro jednotlivé bezpečnostní třídy podle ČSN P ENV 1627 v návaznosti na ČSN EN 12320 Bezpečnostní třída podle ČSN P ENV 1627 Bezpečnostní třída 1
Třída bezpečnosti podle ČSN EN 12320 TB 2
Bezpečnostní třída 2
TB 3
Bezpečnostní třída 3
TB 4
Bezpečnostní třída 4
TB 5
Bezpečnostní třída 5
TB 6
Požadavky pro jednotlivé bezpečnostní třídy podle ČSN P ENV 1627 Základní požadavky pro jednotlivé bezpečnostní třídy jsou uvedeny v tabulce č. 5 shora uvedené normy – doba průlomové odolnosti a celkový čas zkoušky. Zkouška – zkoušky jsou prováděny podle ČSN P ENV 1630. Bezpečnostní třída podle ČSN P ENV 1627 Bezpečnostní třída 1
Aplikace nářadí v příslušné době průlomové odolnosti Bez aplikace
Nezkouší se
Nářadí kategorie A + dodatečné nářadí (páčení ) Nářadí kategorie A+B + dodatečné nářadí (páčení ) Nářadí kategorie A+B+C + dodatečné nářadí (páčení – odseknutí – odvrtání) Nářadí kategorie A+B+C+D + dodatečné nářadí (páčení – odseknutí – odvrtání – odříznutí)
Bezpečnostní třída 2 Bezpečnostní třída 3 Bezpečnostní třída 4 Bezpečnostní třída 5
Doba průlomové odolnosti
3 min 5 min 10 min 15 min
Požadavky - základní informace, identifikace, použití atd. Požadavek – údaj - logo výrobce - označení výrobku – typ – bezpečnostní třída + norma - odolnost proti bumpingu - kontrola počtu efektivních kombinací - kontrola omezujících parametrů – připojovací rozměry, kombinace provedení, modifikace, typická použití atd. - speciální operace – záznamy - výroba náhradních klíčů - konstrukční údaje – tvar otvoru pro klíč, počet a tvar stavítek - další označení, údaje dle výrobce, kód podle ČSN EN 12320:2002 atd.
34
Poznámka
Příloha č. 2
Příloha č. 2: Elektrická zámková zařízení a systémy pro kontrolu vstupů – písm. b) § 30 zákona
Systémy kontroly vstupů Výstup Třída identifikace Třída přístupu Třída prostředí
Certifikát shody podle certifikačního postupu NBÚ ČSN EN 50133-1, ČSN EN 50133-2-1, ČSN CLC/TS 50131-2-2 ČSN EN 50130-5
Požadavky na systémy kontroly vstupů Dle: ČSN EN 50133-1, ČSN EN 50133-2-1, ČSN CLC/TS 50131-2-2 až ČSN CLC/TS 50131-2-5 Požadavek Předpis/čl./kap./tab. Kontrola dokumentace ČSN EN 50133-2-1 4.7 Značení identifikace ČSN EN 50133-2-1 4.8 Rozsah mezních hodnot vstupního napětí ČSN CLC/TS 50131-2-2 až -5 6.9.1, 6.9.2, a odběr proudu* tab. 4 Napájení ČSN EN 50133-2-1 4.5 Kontrola klasifikace identifikace ČSN EN 50133-1 5.1.1 Kontrola třídy přístupů ČSN EN 50133-1 5.1.2 * - Zkoušku provést pokud lze aplikovat
Požadavky na funkční zkoušky společné pro třídu přístupu A i B Dle: ČSN EN 50 133-1 čl. 6.2.3 Požadavek Předpis/čl. Zpracování pro třídu identifikace 1 ČSN EN 50 133-1 5.2.1 e) Zpracování pro třídu identifikace 3 ČSN EN 50 133-1 5.2.1 f) Připojení, odpojení napájení ČSN EN 50 133-1 5.2.2 a) Ochrana programování ČSN EN 50 133-1 5.2.4 c) Ovládání míst přístupu ČSN EN 50 133-1 5.2.5 a) až 5.2.5 f) Hlášení ČSN EN 50 133-1 5.2.8 a), 5.2.8 b) Komunikace s jinými systémy ČSN EN 50 133 5.2.9 a), 5.2.9 b) Použití alternativních prostředků ČSN EN 50 133 5.2.9 c) Připojení a odpojení komunikačních linek ČSN EN 50 133 5.2.9 e)
Doplňkové požadavky pro třídu B Dle: ČSN EN 50133-1, ČSN EN 50133-2-1 Požadavek Předpis/čl./kap. Ochrana programování ČSN EN 50133-1 5.3.4, 5.2.4 Ukládání do paměti a hlášení ČSN EN 50133-1 5.3.8 a), 5.3.8 b), 5.3.8 c) Kapacita paměti událostí ČSN EN 50133-1 5.3.8 d), 5.3.8 e) Kontrola identifikace ČSN EN 50133-1 5.2.6 Kontrola zpracování - časový filtr ČSN EN 50133-1 5.3.1 Kryty ČSN EN 50133-2-1 4.6.1 až 4.6.3 Sabotážní ochrana ČSN EN 50133-2-1 5
35
Příloha č. 2
Vlivy okolního prostředí
ČSN EN 50130-4
ČSN EN 50130-5
Dle: ČSN EN 50130-4, ČSN EN 50130-5, ČSN EN 55022 Typ zkoušky vlivu prostředí, Třída prostředí Předpis/kap. odolnosti proti rušení a IV I II III měření vyzařovaného (vedeného) rušení Suché teplo (provozní) 8 • • • • Chlad (provozní) 10 • • • • Vlhké teplo, konstantní (provozní) 12 • Vlhké teplo, cyklické (provozní) 14 • • • Vnik vody (provozní) 16 (IPX-2) • Vnik vody (provozní) 16 (IPX-4) • Ráz (provozní) 20 • • • • Vibrace, sinusové (provozní) 22 • • • • Změny síťového napájecího napětí 7 •** •** •** •** Poklesy a krátkodobá přerušení síťového 8 •** •** •** •** napájecího napětí Elektrostatický výboj 9 • • • • Rušení vysokofrekvenčním elektromagnetickým 10 • • • • polem Rušení indukované elektromagnetickými poli 11 • • • • Rychlé přechodové děje 12 • • • • Rázový impuls 13 • • • • Rušivé napětí na síťových svorkách ČSN EN 55022 •** •** •** •** třída B, kap. 5 Charakteristiky rádiového rušení ČSN EN 55022 • • • • třída B, kap. 6 • - Zkouška musí být provedena •**- Platí pouze pro zařízení napájená ze sítě
Sestava zkoušeného výrobku:
Požadavky na základní parametry – údaje, identifikace, použití atd. Požadavek - údaj - výrobce - označení výrobku – typ – kategorie použití – stupeň zabezpečení třída + norma - kontrola počtu efektivních kombinací – prohlášení výrobce - kontrola omezujících parametrů – připojovací rozměry, kombinace provedení, modifikace, atd. - speciální funkce – záznamy - konstrukční údaje - další označení, údaje dle výrobce
36
Poznámka
Příloha č. 3
Příloha č. 3: Poplachové systémy – elektrická zabezpečovací signalizace – písm. c) § 30 zákona Příloha zahrnuje: - Ústředna EZS - Detektor pohybu – PIR, MW, UZ a kombinovaný - Detektor rozbití skla - Otřesový detektor - Detektor směrový (závora) - Detektor otevření - Napájecí zdroj - Bezdrátové systémy
Ústředna EZS Výstup Stupeň zabezpečení Třída prostředí
Certifikát shody podle certifikačního postupu NBÚ ČSN EN 50131-1, ČSN CLC/TS 50131-3 ČSN EN 50130-5
Požadavky pro všechny stupně zabezpečení Dle: ČSN EN 50131-1, ČSN CLC/TS 50131-3, ČSN EN 50131-6 ed.2 Požadavek Předpis/čl./kap./tab. Montážní návod, značení výrobku a ČSN EN 50131-1 kap. 14, 15 uživatelské podmínky Prokázání nezávislých povinných funkcí ČSN CLC/TS 8.1, 8.1.7, 12.2 až 12.6.7 na jiných detekčních událostech 50131-3 Údaje pro časování detekce Signál
Trvání
Narušení
400 ms
Tíseň
400 ms
Sabotáž
400 ms
Porucha
10 s
Vyhodnocení časování
10 s
Signalizace (optická a akustická) Maximální zatížení Postupná změna zátěže Skoková změna zátěže Zkrat výstupů*
ČSN CLC/TS 50131-3 ČSN CLC/TS 50131-3 ČSN CLC/TS 50131-3 ČSN CLC/TS 50131-3 ČSN CLC/TS 50131-3 ČSN CLC/TS 50131-3 ČSN CLC/TS 50131-3 ČSN EN 50131-6 ed.2 ČSN EN 50131-6 ed.2 ČSN EN 50131-6 ed.2 ČSN EN 50131-6 ed.2
37
tab. C1 8.9.1 8.9.2 8.9.3 8.9.4 8.9.5. 8.4, 8.4.2, 8.4.3, 8.4.4, 8.4.5, tab. 11 a 12 kap. 7.3 kap. 7.4 kap. 7.5 kap. 7.15
Příloha č. 3 ČSN EN 50131-6 ed.2 ČSN EN 50131-6 ed.2 ČSN EN 50131-6 ed.2 ČSN EN 50131-6 ed.2 ČSN EN 50131-6 ed.2 ČSN EN 50131-6 ed.2 ČSN EN 50131-6 ed.2 ČSN EN 50131-6 ed.2 ČSN EN 50131-6 ed.2 ČSN EN 50131-6 ed.2
Přetížení* Nabíjení Udržování kapacity záložního zdroje* Zvlnění* Poruchy vnějšího zdroje energie* Porucha záložního zdroje Nízké napětí záložního zdroje* Nízké výstupní napětí* Vysokého výstupního napětí* Ochrana proti hlubokému vybití
kap. 7.16 kap. 7.13; 7.18 kap. 7.18 kap. 7.3; 7.5 kap. 7.6; 7.10; 7.10; 7.18 kap. 7.18 kap. 7.7 kap. 7.9 kap. 7.14 kap. 7.17
* - Zkoušku vyžadovat, pokud lze aplikovat Indikace stavů na ústředně Dle: ČSN CLC/TS 50131-3, čl. 8.4, tab. 11 - výběr; ČSN EN 50131-1, tab. 4 St. zabezpečení 1
Požadavek by pass
Střežení
2
3
4
by pass
Střežení
by pass
Střežení
by pass
Střežení
P
-
P
-
P
-
Nastavování střežení Stav střežení
P
P - Povinné
Detekce sabotáže Dle: ČSN CLC/TS 50131-3, čl. 8.6.2, tab. 15 a 16 - výběr St. zabezpečení
Požadavek pro stupeň zabezpečení Otevření krytu normálními prostředky Nástroj – ocelová tyčka o průměru (mm) Oddálení z namontované plochy* Proniknutí krytem
1 P 2,5 -
2 P 2,5 -
3 P 1 P
4 P 1 P
-
-
-
P
P - Povinné * - Platí pro bezdrátovou ústřednu a bezdrátové ovládací zařízení
38
Příloha č. 3
Rozlišení poruch Dle: ČSN CLC/TS 50131-3, čl. 8.7, tab. 18 St. zabezpečení
Požadavek pro stupeň zabezpečení
1
2
3
4
Základní napájecí zdroj
P
P
P
P
Náhradní napájecí zdroj Požadovaná výměna článku (pouze primární články) Porucha výstupu napájení – nízké napětí
P
P
P
P
P
P
P
P
-
-
P*
P
Přenosová zařízení je-li nařízeno
P
P
P
P
P - Povinné * - Platí dle ČSN EN 50131-6
Rozlišení chybných kódů Dle: ČSN CLC/TS 50131-3, čl. 8.2.2, tab. 3 - výběr St. zabezpečení
Požadavek pro stupeň zabezpečení
1
Blokování užívat. rozhraní (počet chybných kódů)
-
Poplach sabotáže - max. počet chybných kódů
-
2 -
3 P 10 P* 21
4 P 3 P 7
P - Povinné * - Musí být alespoň jeden údaj
Ochrana proti sabotáži Dle: ČSN CLC/TS 50131-3, čl. 8.6.1, tab. 14 St. zabezpečení Požadavek pro stupeň zabezpečení 1 2 3 Stupeň ochrany (IK kód) Energie úderem (J)
4
06
06
06
06
1
1
1
1
Záznam událostí do paměti ústředny Dle: ČSN EN 50131-1, čl. 8.10, tab. 14; ČSN CLC/TS 50131-3, čl. 8.10 St. zabezpečení Požadavek pro stupeň zabezpečení 1 2 3 Kapacita paměti (minimální počet událostí) Stálost paměti po výpadku sítě
-
39
100 30 dnů
200 30 dnů
4 500 30 dnů
Příloha č. 3
Způsob monitorování propojení Dle: ČSN EN 50131-1, čl. 8.8.1.3; ČSN CLC/TS 50131-3, čl. 8.8 a 8.9, tab. 19 – výběr příloha A St. zabezpečení Požadavek pro stupeň zabezpečení 1 2 3 4 Stav střežení P P P P (časování ČSN CLC/TS 50131-3, čl. 8.9) 400 ms 400 ms 400 ms 400 ms Monitorování záměny P P P (časový průběh) 60 s 30 s 10 s 120 min 240 min 100 s 10 s Potvrzování propojení (doba) signalizace porucha porucha nebo nebo sabotáž sabotáž ČSN CLC/TS 50131-3, čl. 8.8.2, tab. 19 sabotáž sabotáž P - Povinné
Vlivy okolního prostředí Dle: ČSN EN 50130-4; ČSN EN 50130-5; ČSN EN 55022 Typ zkoušky vlivu prostředí, odolnosti proti rušení Třída prostředí Předpis/kap. a měření vyzařovaného (vedeného) rušení I II III IV Suché teplo (provozní) 8 • • • • ČSN EN 50130-5
Chlad (provozní) Vlhké teplo, konstantní (provozní) Vlhké teplo, cyklické (provozní) Vnik vody (provozní) Vnik vody (provozní) Ráz (provozní)
Rušení indukované elektromagnetickými poli Rychlé přechodové děje Rázový impuls Rušivé napětí na síťových svorkách Charakteristiky rádiového ušení • - Zkouška musí být provedena
40
12
•
14
•
•
•
•
•
•
•
16 (IPX-2)
•
16 (IPX-4) •
•
•
•
22
•
•
•
•
7
•
•
•
•
8
•
•
•
•
9
•
•
•
•
10
•
•
•
•
11
•
•
•
•
12
•
•
•
•
13
•
•
•
•
ČSN EN 55022 třída B, kap. 5
•
•
•
•
ČSN EN 55022 třída B, kap. 6
•
•
•
•
ČSN EN 50130-4
Rušení vysokofrekvenčním elektromagnetickým polem
•
20
Vibrace, sinusové (provozní) Změny síťového napájecího napětí Poklesy a krátkodobá přerušení síťového napájecího napětí Elektrostatický výboj
10
Příloha č. 3
Sestava zkoušeného výrobku:
Požadavky na základní parametry – údaje, identifikace, použití atd. Požadavek - údaj
Poznámka
- výrobce - označení výrobku – typ – kategorie použití – stupeň zabezpečení třída + norma - kontrola počtu efektivních kombinací – prohlášení výrobce - kontrola omezujících parametrů – připojovací rozměry, kombinace provedení, modifikace, atd. - speciální funkce – záznamy - konstrukční údaje - další označení, údaje dle výrobce
41
Příloha č. 3
Detektor pohybu – PIR, MW, UZ a kombinovaný Výstup Stupeň zabezpečení Třída prostředí
Certifikát shody podle certifikačního postupu NBÚ ČSN EN 50131-1, ČSN CLC/TS 50131-2-2 ČSN EN 50130-5
Požadavky pro všechny stupně zabezpečení Dle: ČSN EN 50131-1, ČSN CLC/TS 50131-2-2 až ČSN CLC/TS 50131-2-5 Požadavek Předpis/čl./kap./tab. Montážní návod, značení výrobku ČSN EN 50131-1 kap. 14, 15 a uživatelské podmínky Proudění vzduchu před čidlem* ČSN CLC/TS 50131-2-2 až -5 6.7.1 Odolnost proti viditelnému světlu a světlu* ČSN CLC/TS 50131-2-2 až -5 6.7.2 blízkému IR záření Odolnost proti světlu zářivek** ČSN CLC/TS 50131-2-3 a -4 6.7 Rozsah mezních hodnot vstupního napětí a ČSN CLC/TS 50131-2-2 až -5 6.9.1, 6.9.2, odběr proudu tab. 4 Kontrola funkce při nastavení minimální *** ČSN CLC/TS 50131-2-2 až -5 6.4.4, citlivosti (pokud má čidlo ovládací prvky 6.4.5 umožňující změnu citlivosti) Zpožděné zapnutí a doba zotavení ČSN CLC/TS 50131-2-2 až -5 6.5 Těsnost krytu (ochrana proti vniknutí ČSN CLC/TS 50131-2-2 až -5 6.8.1 existujícími otvory) odolnost proti vniknutí hmyzu * Neplatí pro MW detektory ** Pouze pro MW detektory a kombinované detektory PIR+MW ***Dle specifikace výrobce
Detekční citlivost Dle: ČSN CLC/TS 50131-2-2 až ČSN CLC/TS 50131-2-5, tab. 2 - výběr St. zabezpečení Požadavek Předpis/čl./tab. 1 2 3 4 Pokrytí na hranici detekčního ČSN CLC/TS 50131-2-2 až -5 6.4.1.1 P P P P prostoru - vzpřímený postoj tab. 2 1,0 1,0 1,0 1,0 (m/s) Pomalý pohyb ČSN CLC/TS 50131-2-2 až -5 6.4.1.2 0.3 0.2 0.1 - vzpřímený postoj (m/s) tab. 2 Rychlý pohyb ČSN CLC/TS 50131-2-2 až -5 6.4.2.1 2.0 2.5 3.0 - vzpřímený postoj (m/s) tab. 2 Ostražitý pohyb (m/s) ČSN CLC/TS 50131-2-2 až -5 6.4.3 0.5 0.4 0.3 0.2 (zk. detekce v blízkosti čidla) tab. 2 V V Pl Pl Přerušovaný pohyb ČSN CLC/TS 50131-2-2 až -5 6.4.2.2 0.2 0.1 - vzpřímený postoj (m/s) tab. 2 1,0 1,0 V - Vzpřímený pohyb Pl – Plížení
42
Příloha č. 3
Požadované funkce signalizace Dle: ČSN CLC/TS 50131-2-2 až ČSN CLC/TS 50131-2-5 Požadavek Poplach Sabotáž Napájení odpojené* (výstup poplach, porucha) Samokontrola (testování)**
Předpis/čl./tab. ČSN CLC/TS 50131-2-2 až -5 4.2.1 a 4.2.2, tab. 1 ČSN CLC/TS 50131-2-2 až -5 tab. 1 ČSN CLC/TS 50131-2-2 až -5 tab. 1 ČSN CLC/TS 50131-2-2 až -5 tab. 1
St. zabezpečení 1 2 3 4 P
P
P
P
P
P
P
P
P
P
P
P
-
-
P
P
P - Povinné * - Nepožadováno u sběrnicových systémů ** - Platí pokud výrobce stanoví postup při zkoušce
Ochrana proti sabotáži Dle: ČSN EN 50 131-1, ČSN CLC/TS 50131-2-2 až ČSN CLC/TS 50131-2-5 St. zabezpečení Požadavek Předpis/čl./tab. 1 2 3 4 Nepovolená manipulace ČSN EN 50131-1 8.7.2 P P P P s krytem (otevření) Těsnost krytu (ochrana proti ČSN CLC/TS 50131-2-2 až -5 6.8.1 P P P P vniknutí existujícími otvory) Oddálení z namontované ČSN CLC/TS 50131-2-2 až -5 6.8.2, PB P P plochy tab. 3 Změna orientace (pouze pro ČSN CLC/TS 50131-2-2 až -5 6.8.3, P P P čidla s nastavitelnými držáky) tab. 3 Magnetické pole (odolnost) ČSN CLC/TS 50131-2-2 až -5 6.8.4, P P P 0,15 0,3 1,2 Remanence zkuš. magnetu [T] tab. 3 Zakrytí průzoru ČSN CLC/TS 50131-2-2 až -5 6.8.5, P P tab. 5 P - Povinné PB - Povinné pro bezdrátová čidla
Vlivy okolního prostředí
ČSN EN 50130-5
Dle: ČSN EN 50130-4, ČSN EN 50130-5, ČSN EN 55022 Typ zkoušky vlivu prostředí, odolnosti proti Předpis/kap. rušení a měření vyzařovaného (vedeného) rušení Suché teplo (provozní) 8 Chlad (provozní) 10 Vlhké teplo, konstantní (provozní) 12 Vlhké teplo, cyklické (provozní) 14 Vnik vody (provozní) 16 (IPX-2) Vnik vody (provozní) 16 (IPX-4) Ráz (provozní) 20 Vibrace, sinusové (provozní) 22
43
Třída prostředí I
II
III
IV
• • •
• •
• •
• •
•
• •
•
• •
• •
• •
• • •
Příloha č. 3 ČSN EN 50130-4
Elektrostatický výboj Rušení vysokofrekvenčním elektromagnetickým polem Rušení indukované elektromagnet. poli Rychlé přechodové děje Rázový impuls Charakteristiky rádiového rušení
9 10
11 12 13 ČSN EN 55022 třída B, kap. 6
•
•
•
•
•
•
•
•
• • •
• • •
• • •
• • •
•
•
•
•
• - Zkouška musí být provedena
Požadavky na základní parametry – údaje, identifikace, použití atd. Požadavek - údaj - výrobce - označení výrobku – typ – kategorie použití – stupeň zabezpečení třída + norma - kontrola počtu efektivních kombinací – prohlášení výrobce - kontrola omezujících parametrů – připojovací rozměry, kombinace provedení, modifikace, atd. - speciální funkce – záznamy - konstrukční údaje - další označení, údaje dle výrobce
44
Poznámka
Příloha č. 3
Detektor rozbití skla Výstup Stupeň zabezpečení Třída prostředí
Certifikát shody podle certifikačního postupu NBÚ ČSN EN 50131-1, ČSN EN 50131-1/Z1, ČSN CLC/TS 50131-2-2 ČSN EN 50130-5
Požadavky pro všechny stupně zabezpečení Dle: ČSN EN 50131-1, ČSN EN 50131-1/Z1, ČSN CLC/TS 50131-2-2 až ČSN CLC/TS 50131-2-5 Požadavek Předpis/čl./kap./tab. Montážní návod, značení výrobku ČSN EN 50131-1 kap. 14, 15 a uživatelské podmínky Odolnost proti planým poplachům ČSN EN 50131-1/Z1 NG.2.5.2, 5, 6 Rozsah mezních hodnot vstupního napětí ČSN CLC/TS 50131-2-2 až -5 6.9.1, 6.9.2, tab. 4 a odběr proudu Kontrola funkce při nastavení minimální ČSN EN 50131-1/Z1 NH.1.2 citlivosti (pokud má čidlo ovládací prvky umožňující změnu citlivosti) Zpožděné zapnutí a doba zotavení ČSN CLC/TS 50131-2-2 až -5 6.5 Těsnost krytu (ochrana proti vniknutí ČSN CLC/TS 50131-2-2 až -5 6.8.1 existujícími otvory)* Splnění mezí detekčního prostoru ČSN EN 50131-1/Z1 NG.2.1 * - Zkoušku provést, pokud lze aplikovat
Funkční požadavky Dle: ČSN EN 50131-1/Z1, ČSN CLC/TS 50131-2-2 až ČSN CLC/TS 50131-2-5 St. zabezpečení Požadavek Předpis/čl./tab. 1 2 3 4 Jedna událost v rámci ČSN EN 50131-1/Z1 NG.1 P P P P spektra Více událostí v rámci ČSN EN 50131-1/Z1 NG.1 P spektra (rázová vlna) Autotest na výstupu porucha ČSN EN 50131-1/Z1 NG.2.2.3 P Napájení odpojené ČSN CLC/TS 50131-2-2 až -5 tab. 1 P P P P (výstup poplach, porucha) Stav napájecího napětí ČSN EN 50131-1/Z1 NG.2.2.1 P mimo toleranci P - Povinné
Ochrana proti sabotáži Dle: ČSN EN 50131-1/Z1, ČSN CLC/TS 50131-2-2 až ČSN CLC/TS 50131-2-5 St. zabezpečení Požadavek Předpis/čl./tab. 1 2 3 4 Nepovolená manipulace ČSN EN 50131-1 8.7.2, P P P s krytem (otevření) tab. 13 Magnetické pole (odolnost) ČSN CLC/TS 50131-2-2 6.8.4, P P P 0,15 0,3 1,2 Remanence zkuš. magnetu [T] až -5 tab. 3 Oddálení z namontované ČSN EN 50131-1 8.7.2, PB P P plochy tab. 13 P - Povinné PB - Povinné pro bezdrátová čidla
45
Příloha č. 3
Vlivy okolního prostředí
ČSN EN 50130-4
ČSN EN 50130-5
Dle: ČSN EN 50130-4, ČSN EN 50130-5, ČSN EN 55022 Typ zkoušky vlivu prostředí, Třída prostředí odolnosti proti rušení Předpis/kap. a měření vyzařovaného (vedeného) I II III rušení Suché teplo (provozní) 8 • • • Chlad (provozní) 10 • • • Vlhké teplo, konstantní (provozní) 12 • Vlhké teplo, cyklické (provozní) 14 • • Vnik vody (provozní) 16 (IPX-2) • Vnik vody (provozní) 16 (IPX-4) Ráz (provozní) 20 • • • Vibrace, sinusové (provozní) 22 • • • Elektrostatický výboj 9 • • • Rušení vysokofrekvenčním 10 • • • elektromagnetickým polem Rušení indukované 11 • • • elektromagnet. poli Rychlé přechodové děje 12 • • • Rázový impuls 13 • • • Charakteristiky rádiového rušení
ČSN EN 55022 třída B, kap. 6
•
•
• - Zkouška musí být provedena
Požadavky na základní parametry – údaje, identifikace, použití atd. Požadavek - údaj - výrobce - označení výrobku – typ – kategorie použití – stupeň zabezpečení třída + norma - kontrola počtu efektivních kombinací – prohlášení výrobce - kontrola omezujících parametrů – připojovací rozměry, kombinace provedení, modifikace, atd. - speciální funkce – záznamy - konstrukční údaje - další označení, údaje dle výrobce
46
Poznámka
•
IV • • • • • • • • • • • •
Příloha č. 3
Otřesový detektor Výstup Stupeň zabezpečení Třída prostředí
Certifikát shody podle certifikačního postupu NBÚ ČSN EN 50131-1, ČSN EN 50131-1/Z1, ČSN CLC/TS 50131-2-2 ČSN EN 50130-5
Požadavky pro všechny stupně zabezpečení Dle: ČSN EN 50131-1, ČSN EN 50131-1/Z1, ČSN CLC/TS 50131-2-2 až ČSN CLC/TS 50131-2-5 Požadavek Předpis/čl./kap./tab. Montážní návod, značení výrobku ČSN EN 50131-1 kap. 14, 15 a uživatelské podmínky ČSN EN 50131-1/Z1 NH.1.1- 3 Detekční citlivost (dle parametrů výrobce) Signalizace při vytvoření otvoru (300 x 300) mm Signalizace při vytvoření otvoru (40 x 40) mm Signalizace při vytvoření otvoru (15 x 5) mm Zkouška detekčního pole ČSN EN 50131-1/Z1 NH.2.3 Odolnost proti zdrojům zvuku ČSN EN 50131-1/Z1 NH.1.8.6 Rozsah mezních hodnot vstupního napětí a odběr proudu* Porucha napájení Ověření tolerance citlivosti (pokud má detektor ovládací prvky umožňující změnu citlivosti) Zpožděné zapnutí a doba zotavení* Napájení odpojené* (výstup poplach, porucha) Těsnost krytu (ochrana proti vniknutí existujícími otvory)*
ČSN CLC/TS 50131-2-2 až -5 ČSN EN 50131-1/Z1 ČSN EN 50131-1/Z1
6.9.1, 6.9.2 tab. 4 NH.1.4 NH.1.2
ČSN CLC/TS 50131-2-2 až -5 ČSN CLC/TS 50131-2-2 až -5
6.5 tab. 1
ČSN CLC/TS 50131-2-2 až -5
6.8.1
* - Zkoušku provést, pokud lze aplikovat
Ochrana proti sabotáži Dle: ČSN EN 50131-1, ČSN CLC/TS 50131-2-2 až ČSN CLC/TS 50131-2-5 St. zabezpečení Požadavek Předpis/čl./tab. 1 2 3 4 Nepovolená manipulace ČSN EN 50131-1 8.7.2 P P P s krytem (otevření) tab.13 Oddálení z namontované ČSN EN 50131-1 8.7.2 PB P P plochy tab.13 Magnetické pole (odolnost) ČSN CLC/TS 50131-2-2 6.8.4, P P P 0,15 0,3 1,2 Remanence zkuš. magnetu [T] až -5 tab. 3 P - Povinné PB - Povinné pro bezdrátová čidla
47
Příloha č. 3
Vlivy okolního prostředí
ČSN EN 50130-4
ČSN EN 50130-5
Dle: ČSN EN 50130-4, ČSN EN 50130-5, ČSN EN 55022 Typ zkoušky vlivu prostředí, Třída prostředí odolnosti proti rušení a měření Předpis/kap. vyzařovaného (vedeného) rušení I II III IV Suché teplo (provozní) 8 • • • • Chlad (provozní) 10 • • • • Vlhké teplo, konstantní (provozní) 12 • Vlhké teplo, cyklické (provozní) 14 • • • Vnik vody (provozní) 16 (IPX-2) • Vnik vody (provozní) 16 (IPX-4) • Ráz (provozní) 20 • • • • Vibrace, sinusové (provozní) 22 • • • • Změny síťového napájecího napětí 7 •** •** •** •** Poklesy a krátkodobá přerušení 8 •** •** •** •** síťového napájecího napětí Elektrostatický výboj 9 • • • • Rušení vysokofrekvenčním 10 •* •* •* •* elektromagnetickým polem Rušení indukované elektromagnetickými poli 11 •* •* •* •* Rychlé přechodové děje 12 •* •* •* •* Rázový impuls 13 •* •* •* •* Rušivé napětí na síťových svorkách ČSN EN 55022 •** •** •** •** třída B, kap. 5 Charakteristiky rádiového rušení ČSN EN 55022 •* •* •* •* třída B, kap. 6 • - Zkouška musí být provedena •* - Platí pouze pro zařízení s aktivními prvky •** - Platí pouze pro zařízení napájená ze sítě
Požadavky na základní parametry – údaje, identifikace, použití atd. Požadavek - údaj - výrobce - označení výrobku – typ – kategorie použití – stupeň zabezpečení třída + norma - kontrola počtu efektivních kombinací – prohlášení výrobce - kontrola omezujících parametrů – připojovací rozměry, kombinace provedení, modifikace, atd. - speciální funkce – záznamy - konstrukční údaje - další označení, údaje dle výrobce
48
Poznámka
Příloha č. 3
Detektor směrový (závora) Výstup
Certifikát shody podle certifikačního postupu NBÚ ČSN EN 50131-1, ČSN EN 50131-1/Z1, ČSN CLC/TS 50131-2-2 ČSN EN 50130-5
Stupeň zabezpečení Třída prostředí
Podmínky pro všechny stupně zabezpečení Dle: ČSN EN 50131-1, ČSN EN 50131-1/Z1, ČSN CLC/TS 50131-2-2 až ČSN CLC/TS 50131-2-5 Požadavek Předpis/čl./kap./tab. Montážní návod, značení výrobku ČSN EN 50131-1 kap.14, 15 a uživatelské podmínky Rozsah mezních hodnot vstupního napětí ČSN CLC/TS 50131-2-2 až -5 6.9.1, 6.9.2, a odběr proudu tab. 4 ČSN EN 50131-1/Z1 NJ.2.1 Kontrola detekčního pole Vliv mlhy, deště, sněžení – IČ závora ČSN EN 50131-1/Z1 NJ.2.3 Zařízení zůstává funkční ještě při snížení přenášené energie na 75 % původní hodnoty Vliv mlhy, deště, sněžení – MW závora ČSN EN 50131-1/Z1 NJ.2.4 Zařízení zůstává funkční při snížení přenášené energie. Zpožděné zapnutí a doba zotavení ČSN CLC/TS 50131-2-2 až -5 6.5 Potřebná doba přerušení spojnice P-V ČSN EN 50131-1/Z1 NJ.1.1 a (jen pro IČ závory) NJ.1.2
Zkouška rychlosti chůze a držení těla Dle: ČSN EN 50131-1/Z1 tab. NJ.1
Pomalý pohyb - vzpřímený postoj (m/s) ČSN EN 50131-1/Z1
NJ.2.1
St. zabezpečení 1 2 3 4 0.3 0.2 0.1
Rychlý pohyb - vzpřímený postoj (m/s)
ČSN EN 50131-1/Z1
NJ.2.1
-
2.0
2.5
3.0
Ostražitý pohyb – plížení (m/s) (jen pro MW čidla)
ČSN EN 50131-1/Z1
NJ.2.1
-
-
0.2
0.1
Požadavek
Předpis/čl.
Požadované funkce signalizace Dle: ČSN CLC/TS 50131-2-2 až ČSN CLC/TS 50131-2-5 St. zabezpečení 1 2 3 4
Požadavek Poplach Sabotáž Napájení odpojené* (výstup poplach, porucha)
ČSN CLC/TS 50131-2-2 až 5 4.2.1 a 4.2.2 tab. 1 ČSN CLC/TS 50131-2-2 až 5 tab. 1 ČSN CLC/TS 50131-2-2 až 5 tab. 1
P - Povinné * - Nepožadováno u sběrnicových systémů
49
P
P
P
P
P
P
P
P
P
P
P
P
Příloha č. 3
Ochrana proti sabotáži Dle: ČSN EN 50 131-1, ČSN CLC/TS 50131-2-2 až ČSN CLC/TS 50131-2-5 St. zabezpečení Požadavek Předpis/čl./tab. 1 2 3 4 Nepovolená manipulace s krytem ČSN EN 50131-1 8.7.2, P P P P (otevření) tab.13 Těsnost krytu (ochrana proti ČSN CLC/TS 6.8.1 P P P P vniknutí existujícími otvory) 50131-2-2 až -5 tab. 3 Oddálení z namontované plochy ČSN EN 50131-1 8.7.2,tab.1 PB P P 3 Magnetické pole (odolnost) ČSN CLC/TS 6.8.4, P P P 0,15 0,3 1,2 Remanence zkuš. magnetu [T] 50131-2-2 až -5 tab. 3 P - Povinné PB - Povinné pro bezdrátové detektory
Vlivy okolního prostředí
ČSN EN 50130-4
ČSN EN 50130-5
Dle: ČSN EN 50130-4, ČSN EN 50130-5, ČSN EN 55022, ČAP P 131-2-9, kap. 4 Typ zkoušky vlivu prostředí, odolnosti Třída prostředí Předpis/kap. proti rušení a měření vyzařovaného I II III IV (vedeného) rušení Suché teplo (provozní) 8 • • • • Chlad (provozní) 10 • • • • Vlhké teplo, konstantní (provozní) 12 • Vlhké teplo, cyklické (provozní) 14 • • • Vnik vody (provozní) 16 (IPX-2) • Vnik vody (provozní) 16 (IPX-4) • Ráz (provozní) 20 • • • • Vibrace, sinusové (provozní) 22 • • • • Změny síťového napájecího napětí 7 •** •** •** •** Poklesy a krátkodobá přerušení 8 •** •** •** •** síťového napájecího napětí Elektrostatický výboj 9 • • • • Rušení vysokofrekvenčním 10 •* •* •* •* elektromagnetickým polem Rušení indukované elektromagnetickými poli 11 •* •* •* •* Rychlé přechodové děje 12 •* •* •* •* Rázový impuls 13 •* •* •* •* Rušivé napětí na síťových svorkách ČSN EN 55022 •** •** •** •** třída B, kap.5 Charakteristiky rádiového rušení ČSN EN 55022 •* •* •* •* třída B, kap. 6 • - Zkouška musí být provedena •* - Platí pouze pro zařízení s aktivními prvky •** - Platí pouze pro zařízení napájená ze sítě
50
Příloha č. 3
Požadavky na základní parametry – údaje, identifikace, použití atd. Požadavek - údaj
Poznámka
- výrobce - označení výrobku – typ – kategorie použití – stupeň zabezpečení třída + norma - kontrola počtu efektivních kombinací – prohlášení výrobce - kontrola omezujících parametrů – připojovací rozměry, kombinace provedení, modifikace, atd. - speciální funkce – záznamy - konstrukční údaje - další označení, údaje dle výrobce
51
Příloha č. 3
Detektor otevření
Výstup Stupeň zabezpečení Třída prostředí
Certifikát shody podle certifikačního postupu NBÚ ČSN EN 50131-1, ČSN CLC/TS 50131-2-6 ČSN EN 50130-5
Podmínky pro všechny stupně zabezpečení Dle: ČSN EN 50131-1, ČSN CLC/TS 50131-2-6, ČSN EN 50130-5 Požadavek Předpis/čl./kap./tab. Montážní návod, značení výrobku a uživatelské ČSN EN 50131-1 kap. 14, 15 podmínky Kontrola funkce - vzdálenost rozpojení dle údajů ČSN CLC/TS 50131-2-6 6.3., 6.3.1 výrobce a klidový stav při návratu do 50 % max. vzdálenosti Těsnost krytu ČSN CLC/TS 50131-2-6 6.5.1 (ochrana proti vniknutí existujícími otvory)* Klimatická odolnost (kontrola údajů výrobce v TP, ČSN EN 50130-5 6.3.1, 6.3.2 5.5.1.2 jejich ověření a porovnání s požadavky na třídu ČSN EN 50134-2 prostředí předpokládaného použití). Isolační odpor po klimatických zkouškách větší než 10 MΩ, přechodový odpor menší než 0.1Ω Mechanická odolnost kód IK 04 dle ČSN EN 50102* ČSN EN 50130-5 kap. 20 tab. 14 •
- Zkoušku provést, pokud lze aplikovat
Ochrana proti sabotáži Dle: ČSN CLC/TS 50131-2-6 Požadavek krat/přerušení (sabotáž) Odolnost proti magnetickým polím Remanence zkuš. magnetu [T] Nepovolená manipulace krytem* Oddálení z namontované plochy**
Předpis/čl./tab. ČSN CLC/TS 50131-2-6 6.5, tab. 1 ČSN CLC/TS 50131-2-6 6.5.3, tab. 2 ČSN CLC/TS 50131-2-6 6.5.1, tab. 2 ČSN CLC/TS 50131-2-6 6.5.2
P - Povinné * - Zkoušku provést pokud lze aplikovat ** - Požadováno pouze pro bezdrátové detektory
52
St. zabezpečení 1 2 3 4 P P P -
-
P 0,3
P 1,2
-
P
P
P
-
P
P
P
Příloha č. 3
Vlivy okolního prostředí
ČSN EN 50130-4
ČSN EN 50130-5
Dle: ČSN EN 50130-4, ČSN EN 50130-5, ČSN EN 55022 Typ zkoušky vlivu prostředí, Třída prostředí odolnosti proti rušení Předpis/kap. a měření vyzařovaného I II III (vedeného) rušení Suché teplo (provozní) 8 • • • Chlad (provozní) 10 • • • Vlhké teplo, konstantní (provozní) 12 • Vlhké teplo, cyklické (provozní) 14 • • Vnik vody (provozní) 16 (IPX-2) • Vnik vody (provozní) 16 (IPX-4) Ráz (provozní) 20 • • • Vibrace, sinusové (provozní) 22 • • • Elektrostatický výboj 9 • • • Rušení vysokofrekvenčním 10 •* •* •* elektromagnetickým polem Rušení indukované 11 •* •* •* elektromagnetickými poli Rychlé přechodové děje 12 •* •* •* Rázový impuls 13 •* •* •* Charakteristiky rádiového rušení
ČSN EN 55022 třída B, kap. 6
•*
•*
•*
• - Zkouška musí být provedena •* - Platí pouze pro zařízení s aktivními prvky
Požadavky na základní parametry – údaje, identifikace, použití atd. Požadavek - údaj - výrobce - označení výrobku – typ – kategorie použití – stupeň zabezpečení třída + norma - kontrola počtu efektivních kombinací – prohlášení výrobce - kontrola omezujících parametrů – připojovací rozměry, kombinace provedení, modifikace, atd. - speciální funkce – záznamy - konstrukční údaje - další označení, údaje dle výrobce
53
Poznámka
IV • • • • • • • •* •* •* •* •*
Příloha č. 3
Napájecí zdroj
Výstup Stupeň zabezpečení Třída prostředí
Certifikát shody podle certifikačního postupu NBÚ ČSN EN 50131-6 ed. 2 ČSN EN 50130-5
Požadavky pro všechny stupně zabezpečení Dle: ČSN EN 50131- 6 ed.2 Požadavek
Předpis/čl.
Kontrola průvodní dokumentace
ČSN EN 50131- 6
(7.24.1) kap. 6
Značení výrobku
ČSN EN 50131- 6
(7.24.1) kap. 5
Maximální zatížení
ČSN EN 50131- 6
kap. 7.3
ČSN EN 50131- 6
kap. 7.4
ČSN EN 50131- 6
kap. 7.5
Zkrat
ČSN EN 50131- 6
kap. 7.15
Přetížení
ČSN EN 50131- 6
kap. 7.16
Nabíjení
ČSN EN 50131- 6
kap. 7.13; 7.18
Udržování kapacity zdroje (kapacita akumulátoru)
ČSN EN 50131- 6
kap. 7.18
Zvlnění
ČSN EN 50131- 6
kap. 7.3; 7.5
Porucha vnějšího zdroje energie
ČSN EN 50131- 6
kap. 7.6; 7.10; 7.11; 7.18
Porucha záložního zdroje
ČSN EN 50131- 6
kap. 7.18
Nízké napětí záložního zdroje
ČSN EN 50131- 6
kap. 7.7
Nízké výstupní napětí
ČSN EN 50131- 6
kap. 7.9
Vysoké výstupní napětí
ČSN EN 50131- 6
kap. 7.14
Ochrana proti hlubokému vybití
ČSN EN 50131- 6
kap. 7.17
Ochrana proti sabotáži
ČSN EN 50131- 6
kap. 7.19; 7.20
Detekce sabotáže
ČSN EN 50131- 6
kap. 7.21
Stabilita výstupního napětí - postupná změna zátěže Stabilita výstupního napětí - skoková změna zátěže
54
Příloha č. 3
Vlivy okolního prostředí
ČSN EN 50130-4
ČSN EN 50130-5
Dle: ČSN EN 50130-4, ČSN EN 50130-5, ČSN EN 55022 Typ zkoušky vlivu prostředí, Třída prostředí Předpis/kap. odolnosti proti rušení a I II III IV měření vyzařovaného (vedeného) rušení Suché teplo (provozní) 8 • • • • Chlad (provozní) 10 • • • • Vlhké teplo, konstantní (provozní) 12 • Vlhké teplo, cyklické (provozní) 14 • • • Vnik vody (provozní) 16 (IPX-2) • Vnik vody (provozní) 16 (IPX-4) • Ráz (provozní) 20 • • • • Vibrace, sinusové (provozní) 22 • • • • Změny síťového napájecího napětí 7 • • • • Poklesy a krátkodobá přerušení 8 • • • • síťového napájecího napětí Elektrostatický výboj 9 • • • • Rušení vysokofrekvenčním 10 • • • • elektromagnetickým polem Rušení indukované elektromagnetickými poli 11 • • • • Rychlé přechodové děje 12 • • • • Rázový impuls 13 • • • • Rušivé napětí na síťových svorkách ČSN EN 55022 • • • • třída B, kap. 5 Charakteristiky rádiového rušení ČSN EN 55022 • • • • třída B, kap. 6 • - Zkouška musí být provedena
Sestava zkoušeného výrobku:
Požadavky na základní parametry – údaje, identifikace, použití atd. Požadavek - údaj
Poznámka
- výrobce - označení výrobku – typ – kategorie použití – stupeň zabezpečení třída + norma - kontrola počtu efektivních kombinací – prohlášení výrobce - kontrola omezujících parametrů – připojovací rozměry, kombinace provedení, modifikace, atd. - speciální funkce – záznamy - konstrukční údaje - další označení, údaje dle výrobce
55
Příloha č. 3
Bezdrátové systémy Výstup Stupeň zabezpečení Třída prostředí
Certifikát shody podle certifikačního postupu NBÚ ČSN EN 50131-1, ČSN EN 50131-1/Z1 ČSN EN 50130-5
Požadavky pro všechny stupně zabezpečení
Přenosové zařízení k ústředně Ústředna k výstražním u zařízení Ústředna k přenosové mu zařízení
Výstražné zařízení k ústředně
Čidlo k ústředně
St. zabezpečení
Dle: ČSN EN 50131-1, ČSN EN 50131-1/Z1 Požadavek Předpis/čl./kap./tab. Montážní návod, značení výrobku ČSN EN 50131-1 kap. 14, 15 a uživatelské podmínky Kontrola odolnosti proti zhoršení přenosové cesty pro ČSN EN 50131-1/Z1 NP.1.1 stupeň zabezpečení 3 a 4 Kontrola zajištění míry kolize pro stupeň ČSN EN 50131-1/Z1 NP.1.2 zabezpečení 3 a 4 Odolnost proti záměně signálů a prvků ČSN EN 50131-1/Z1 NP.1.3 St. zabezpečení Identifikační kódy 1 256 2 10 000 3 100 000 4 1000 000 Odolnost proti rušení ČSN EN 50131-1/Z1 NP.2 Monitorování přenosové cesty – periodická ČSN EN 50131-1/Z1 NP.2.3 komunikace Detekce poruchy v periodické komunikaci ČSN EN 50131-1/Z1 NP.2.3.1 Doba periodické komunikace
1 2 3 4
4h 2 h* 2 h* 2h 2h 1h 1h 1h 1h 1h 15 min 15 min 15 min 15 min 15 min Komunikace před nastavováním střežení St. zabezpečení Identifikační kódy 1 2 2h 3 60 s 4 10 s Detekce rušivého signálu pro stupně zabezpečení 3 a 4 Signalizace demontáže nebo poškození antény přenosového zařízení Signalizace stavu napájení z primárních článků Sabotážní ochrana
ČSN EN 50131-1/Z1
tab. NP. 4
ČSN EN 50131-1/Z1
NP.2.3.2
ČSN EN 50131-1/Z1
NP.2.4
ČSN EN 50131-1/Z1
NP.2.5
ČSN EN 50131-1
8.7.2
* - Během nastavování střežení může být dosažitelnost propojení signalizována akusticky, opticky pouze ústřednou nebo výstražným zařízením
56
Příloha č. 3 Vlivy okolního prostředí Pro jednotlivé komponenty platí stejné požadavky pro ověření třídy prostředí jako pro komponenty EZS podobného charakteru použití.
ČSN EN 50130-4
ČSN EN 50130-5
Dle: ČSN EN 50130-4, ČSN EN 50130-5, ČSN EN 55022 Typ zkoušky vlivu prostředí, odolnosti Třída prostředí Předpis/kap. proti rušení a měření vyzařovaného I II III IV (vedeného) rušení Suché teplo (provozní) 8 • • • • Chlad (provozní) 10 • • • • Odolnost proti změnám teploty (provozní) 11 •° •° •° •° Vlhké teplo, konstantní (provozní) 12 • Vlhké teplo, cyklické (provozní) 14 • • • Vnik vody (provozní) 16 (IPX-2) • Vnik vody (provozní) 16 (IPX-4) • Ráz (provozní) 20 • • • • Volný pád (provozní) 21 •° •° •° •° Vibrace, sinusové (provozní) 22 • • • • Změny síťového napájecího napětí 7 •** •** •** •** Poklesy a krátkodobá přerušení síťového 8 •** •** •** •** napájecího napětí Elektrostatický výboj 9 • • • • Rušení vysokofrekvenčním 10 • • • • elektromagnetickým polem Rušení indukované elektromagnetickými poli 11 • • • • Rychlé přechodové děje 12 • • • • Rázový impuls 13 • • • • Rušivé napětí na síťových svorkách ČSN EN 55022 •** •** •** •** třída B, kap. 5 Charakteristiky rádiového rušení ČSN EN 55022 • • • • třída B, kap. 6 • - Zkouška musí být provedena •** - Platí pouze pro zařízení napájená ze sítě •° - Platí pouze pro přenosné komponenty systémů
Sestava zkoušeného výrobku:
Požadavky na základní parametry – údaje, identifikace, použití atd. Požadavek - údaj - výrobce - označení výrobku – typ – kategorie použití – stupeň zabezpečení třída + norma - kontrola počtu efektivních kombinací – prohlášení výrobce - kontrola omezujících parametrů – připojovací rozměry, kombinace provedení, modifikace, atd. - speciální funkce – záznamy - konstrukční údaje - další označení, údaje dle výrobce
57
Poznámka
Příloha č. 4
Příloha č. 4: Speciální televizní systémy – písm. d) § 30 zákona
Systémy CCTV, kamery
Výstup Stupeň zabezpečení Třída prostředí
Certifikát shody podle certifikačního postupu NBÚ ČSN EN 50131-1, ČSN EN 50132-2-1 ČSN EN 50130-5
Základní požadavky Dle: ČSN EN 50131-1, ČSN EN 50132-2-1, ČSN EN 50132-7 Požadavek Předpis/čl./kap./tab. Montážní návod, značení výrobku a uživatelské ČSN EN 50131-1 kap. 14, 15 podmínky Typ snímacího prvku ČSN EN 50132-2-1 4.1.1 Standardní hodnota výstupní impedance ČSN EN 50132-2-1 4.2.1 Polarita signálu ČSN EN 50132-2-1 4.2.2 Jmenovitá hodnota amplitudy úplného televizního ČSN EN 50132-2-1 4.2.3 signálu Jmenovitá hodnota obrazového signálu ČSN EN 50132-2-1 4.2.4 Maximální úroveň obrazového signálu ČSN EN 50132-2-1 4.2.5 Synchronizační část úplného televizního signálu ČSN EN 50132-2-1 4.2.6 Stejnosměrné napětí na zakončeném výstupu ČSN EN 50132-2-1 4.2.7 Rozsah provozního napětí Technické podmínky výrobce Mezní rozlišovací schopnost ČSN EN 50132-2-1 6.5 Automatické řízení zisku ČSN EN 50132-2-1 6.6 Úroveň černé ČSN EN 50132-2-1 6.8
58
Příloha č. 4
Vlivy okolního prostředí
ČSN EN 50130-4
ČSN EN 50130-5
Dle: ČSN EN 50130-4, ČSN EN 50130-5, ČSN EN 55022 Typ zkoušky vlivu prostředí, odolnosti Třída prostředí Předpis/kap. proti rušení a měření vyzařovaného I II III IV (vedeného) rušení Suché teplo (provozní) 8 • • • • Chlad (provozní) 10 • • • • Vlhké teplo, konstantní (provozní) 12 • Vlhké teplo, cyklické (provozní) 14 • • • Vnik vody (provozní) 16 (IPX-2) • Vnik vody (provozní) 16 (IPX-4) • Ráz (provozní) 20 • • • • Vibrace, sinusové (provozní) 22 • • • • Změny síťového napájecího napětí 7 •** •** •** •** Poklesy a krátkodobá přerušení síťového 8 •** •** •** •** napájecího napětí Elektrostatický výboj 9 • • • • Rušení vysokofrekvenčním elektromagnetickým 10 • • • • polem Rušení indukované elektromagnetickými poli 11 • • • • Rychlé přechodové děje 12 • • • • Rázový impuls 13 • • • • ČSN EN 55022 Rušivé napětí na síťových svorkách •** •** •** •** třída B, kap. 5 ČSN EN 55022 Charakteristiky rádiového rušení • • • • třída B, kap. 6 • - Zkouška musí být provedena •** - Platí pouze pro zařízení napájená ze sítě
Sestava zkoušeného výrobku:
Požadavky na základní parametry – údaje, identifikace, použití atd. Požadavek - údaj - výrobce - označení výrobku – typ – kategorie použití – stupeň zabezpečení třída + norma - kontrola počtu efektivních kombinací – prohlášení výrobce - kontrola omezujících parametrů – připojovací rozměry, kombinace provedení, modifikace, atd. - speciální funkce – záznamy - konstrukční údaje - další označení, údaje dle výrobce
59
Poznámka
Příloha č. 4
Systémy CCTV, řídící jednotky Výstup Stupeň zabezpečení Třída prostředí
Certifikát shody podle certifikačního postupu NBÚ ČSN EN 50131-1, ČSN EN 50132-2-1 ČSN EN 50130-5
Základní požadavky Dle: ČSN EN 50131-1, ČSN EN 50132-2-1, ČSN EN 50132-4-1 Požadavek
Předpis/čl./kap./tab.
Montážní návod, značení výrobku a uživatelské podmínky Standard rozkladu obrazu a synchronizace vst.
ČSN EN 50131-1
kap.14, 15
ČSN EN 50132- 4-1
4.2
Synchronizační standard výstup
ČSN EN 50132- 2-1
4.10
Vstupní impedance Standardní hodnota výstupní impedance
ČSN EN 50132- 4-1
4.4
ČSN EN 50132-2-1
4.2.1
Úroveň vstupního signálu a polarita
ČSN EN 50132- 4-1
4.5
Výstup videosignálu
ČSN EN 50132-2-1
4.2.2 - 4.2.7
Horizontální rozlišovací schopnost - výstup
ČSN EN 50132- 4-1
4.8
Stupnice šedé - výstup
ČSN EN 50132- 4-1
4.13
Napájení
ČSN EN 50132- 4-1
4.15
Vlivy okolního prostředí
ČSN EN 50130-4
ČSN EN 50130-5
Dle: ČSN EN 50130-4, ČSN EN 50130-5, ČSN EN 55022 Typ zkoušky vlivu prostředí, odolnosti Třída prostředí Předpis/kap. proti rušení a měření vyzařovaného I II III IV (vedeného) rušení Suché teplo (provozní) 8 • • • • Chlad (provozní) 10 • • • • Vlhké teplo, konstantní (provozní) 12 • Vlhké teplo, cyklické (provozní) 14 • • • Vnik vody (provozní) 16 (IPX-2) • Vnik vody (provozní) 16 (IPX-4) • Ráz (provozní) 20 • • • • Vibrace, sinusové (provozní) 22 • • • • Změny síťového napájecího napětí 7 •** •** •** •** Poklesy a krátkodobá přerušení síťového napájecího 8 •** •** •** •** napětí Elektrostatický výboj 9 • • • • Rušení vysokofrekvenčním elektromagnetickým 10 • • • • polem Rušení indukované elektromagnetickými poli 11 • • • • Rychlé přechodové děje 12 • • • • Rázový impuls 13 • • • • Rušivé napětí na síťových svorkách ČSN EN 55022 •** •** •** •** třída B, kap. 5 Charakteristiky rádiového rušení ČSN EN 55022 • • • • třída B, kap. 6 • - Zkouška musí být provedena •** - Platí pouze pro zařízení napájená ze sítě
60
Příloha č. 4
Specifické požadavky Dle parametrů stanovených výrobcem Požadavek Dokumentace / postup Přístup k ovládání a programování Výstupy pro externí zařízení Výstupy pro poplachovou signalizaci Poplachové vstupy Signalizace ztráty videosignálu Detekce pohybu Kapacita záznamu Tolerance časových údajů Rychlost vyhledávání snímků Další:
Sestava zkoušeného výrobku:
Požadavky na základní parametry – údaje, identifikace, použití atd. Požadavek - údaj - výrobce - označení výrobku – typ – kategorie použití – stupeň zabezpečení třída + norma - kontrola počtu efektivních kombinací – prohlášení výrobce - kontrola omezujících parametrů – připojovací rozměry, kombinace provedení, modifikace, atd. - speciální funkce – záznamy - konstrukční údaje - další označení, údaje dle výrobce
61
Poznámka
Příloha č. 5
Příloha č. 5: Tísňové systémy – písm. e) § 30 zákona
Tísňové systémy (tísňové hlásiče)
Výstup Stupeň zabezpečení Třída prostředí
Certifikát shody podle certifikačního postupu NBÚ ČSN EN 50131-1, ČSN EN 50134-2, ČSN CLC/TS 50131-2-2 ČSN EN 50130-5
Podmínky pro všechny stupně zabezpečení Dle: ČSN EN 50131-1, ČSN EN 50134-2, ČSN CLC/TS 50131-2-2 až ČSN CLC/TS 50131-2-5 Požadavek Předpis/čl./kap./tab. Montážní návod, značení výrobku a uživatelské ČSN EN 50131-1 podmínky Všeobecné a funkční požadavky ČSN EN 50134-2
kap. 14, 15
Funkce v rozsahu napájecího napětí (bezdrátová)
ČSN EN 50134-2
Pevné aktivační zařízení Přenosné aktivační zařízení s jistícím páskem kolem krku Přechodový a izolační odpor mechanického kontaktu. Mezní spouštěcí síly pevného tlačítka (přenosná) Mechanická odolnost tlačítka -působením na střed tlačítka (přenosná) Mezní spouštění síly pro pevné tahové aktivační zařízení Mezní trvalá síla pro pevné tahové aktivační zařízení (přenosné) Mechanická odolnost pevného aktivačního zařízení Vlastnosti bezdrátového přenosu* Rozsah mezních hodnot vstupního napětí a odběr proudu**
ČSN EN 50134-2
4.1, 4.2 5.5.1.1, (5.5.2.1) 5.5.3
ČSN EN 50134-2
5.5.4
ČSN EN 50134-2
5.5.1.2
ČSN EN 50134-2 ČSN EN 50134-2
5.5.5.1, (5.5.6.1) 5.5.5.2,
Napájení odpojené** * - Zkoušku provést, pokud lze aplikovat ** - Platí pouze pro zařízení s aktivními prvky
62
(5.5.6.2) ČSN EN 50134-2
5.5.7.1
ČSN EN 50134-2
5.5.7.2, 5.5.8.2
ČSN EN 50134-2
5.5.7.3
ČSN EN 50134-2 ČSN CLC/TS 50131-2-2 až 5 ČSN CLC/TS 50131-2-2 až -5
5.6, tab. 1 6.9.1, 6.9.2 tab. 4 tab. 1
Příloha č. 5
Detekce sabotáže Dle: ČSN EN 50131-1, ČSN CLC/TS 50131-2-2 až ČSN CLC/TS 50131-2-5 St. zabezpečení Požadavek Předpis/čl./tab. 1 2 3 4 Otevření pomocí normálních ČSN EN 50131-1 8.7.2 P P P P prostředků Vniknutí do ovládacího a ČSN EN 50131-1 8.7.2 P P signalizačního zařízení Oddálení z nainstalované plochy* ČSN EN 50131-1 8.7.2 P Magnetické pole (odolnost) 6.8.4 P P P ČSN CLC/TS 50131-2-2 až 5 0,15 0,3 1,2 Remanence zkuš. magnetu [T] tab. 3 P - Povinné * - Zkoušku provést, pokud lze aplikovat
Vlivy okolního prostředí
ČSN EN 50130-4
ČSN EN 50130-5
Dle: ČSN EN 50130-4, ČSN EN 50130-5, ČSN EN 55022 Typ zkoušky vlivu prostředí, odolnosti Třída prostředí Předpis/kap. proti rušení a měření vyzařovaného IV I II III (vedeného) rušení Suché teplo (provozní) 8 • • • • Chlad (provozní) 10 • • • • Odolnost proti změnám teploty (provozní) 11 •° •° •° •° Vlhké teplo, konstantní (provozní) 12 • Vlhké teplo, cyklické (provozní) 14 • • • Vnik vody (provozní) 16 (IPX-2) • Vnik vody (provozní) 16 (IPX-4) • Ráz (provozní) 20 • • • • Volný pád (provozní) 21 •° •° •° •° Vibrace, sinusové (provozní) 22 • • • • Změny síťového napájecího napětí 7 •** •** •** •** Poklesy a krátkodobá přerušení síťového 8 •** •** •** •** napájecího napětí Elektrostatický výboj 9 • • • • Rušení vysokofrekvenčním elektromagnetickým 10 •* •* •* •* polem Rušení indukované elektromagnetickými poli 11 •* •* •* •* Rychlé přechodové děje 12 •* •* •* •* Rázový impuls 13 •* •* •* •* Rušivé napětí na síťových svorkách ČSN EN 55022 •** •** •** •** třída B, kap. 5 Charakteristiky rádiového rušení ČSN EN 55022 •* •* •* •* třída B, kap. 6 • - Zkouška musí být provedena •* - Platí pouze pro zařízení s aktivními prvky
•** - Platí pouze pro zařízení napájená ze sítě •° - Platí pouze pro přenosné komponenty systémů
63
Příloha č. 5
Požadavky na základní parametry – údaje, identifikace, použití atd. Požadavek - údaj - výrobce - označení výrobku – typ – kategorie použití – stupeň zabezpečení třída + norma - kontrola počtu efektivních kombinací – prohlášení výrobce - kontrola omezujících parametrů – připojovací rozměry, kombinace provedení, modifikace, atd. - speciální funkce – záznamy - konstrukční údaje - další označení, údaje dle výrobce
64
Poznámka
Příloha č. 6
Příloha č. 6: Zařízení elektrické požární signalizace – písm. f) § 30 zákona
Zařízení elektrické požární signalizace
Zařízení elektrické požární signalizace jsou technické prostředky, které patří mezi stanovené výrobky uvedené v příloze č. 2, skupina výrobků 10, poř. č. 3 – „Výrobky pro požární poplach/detekci, stabilní hašení požáru, řízení požáru a kouře a pro potlačování výbuchu ve stavbách“, nařízení vlády č. 163/2002 Sb., kterým se stanoví technické požadavky na vybrané stavební výrobky.
Pro tyto výrobky je stanoven postup posuzování shody podle § 5 nařízení vlády č. 163/2002 Sb. Podle § 5, odst. 4) autorizovaná osoba provádí pravidelný dohled nad řádným fungováním systému řízení výroby u výrobce nebo nad řádným fungováním systému řízení výroby u dovozce a kontrolu dodržení stanovených požadavků u výrobku.
Odborný posudek, pro zařízení elektrické požární signalizace jako technického prostředku používaného pro ochranu utajovaných informací, je vydávaný akreditovaným subjektem pouze na základě expertního posouzení žadatelem poskytnuté dokumentace (protokolů zkoušek, certifikátů a dalších podkladů) bez přímé účasti na normami předepsaných zkouškách.
65
Příloha č. 7
Příloha č. 7: Zařízení sloužící k vyhledávání nebezpečných látek nebo předmětů – písm. g) § 30 zákona
Detektory kovů Výstup Stupeň zabezpečení Třída prostředí
Certifikát shody podle certifikačního postupu NBÚ NIJ-STD-0601.02, NIJ-STD-0602.01, ČSN EN 50131-1 ČSN EN 50130-5
Průchozí detektory kovů Dle: NIJ-STD-0601.02, ČSN EN 50131-1 Požadavek* Předpis/čl./kap. Montážní návod, značení výrobku ČSN EN 50131-1 kap. 14, 15, a uživatelské podmínky NIJ-SDT-0601.02 kap. 2.9 Definice zkušebních míst a podmínek zkoušení NIJ-SDT-0601.02 kap. 3 čl. 3.1 až 3.5 Zkouška při ukrytí na těle NIJ-SDT-0601.02 kap. 4 Pokrytí NIJ-SDT-0601.02 4.3 Detekční citlivost NIJ-SDT-0601.02 2.3.1 Průchod s neškodnými předměty NIJ-SDT-0601.02 5.4 Akustická poplachová signalizace NIJ-SDT-0601.02 3.3.2 Optická poplachová signalizace NIJ-SDT-0601.02 3.3.3 Zkouška funkce v blízkosti kovových panelů NIJ-SDT-0601.02 3.4 Zkouška funkce ovlivnění železobetonovým NIJ-SDT-0601.02 3.4.2 podlažím Zkouška neškodnými předměty NIJ-SDT-0601.02 5.4 Definice zkušebních předmětů NIJ-SDT-0601.02 kap. 5 Navazující zkoušky a požadavky NIJ-SDT-0601.02 kap. 6 * - Zpracované požadavky na funkční zkoušky průchozích detektorů kovů v souladu s novelizovanou normou NIJ-STD-0601.02. Požadavek NBÚ, zpracováno a odesláno ve 10/2009 - potvrzeno 1/2010.
Přenosné ( ruční) detektory kovů Dle: NIJ-STD-0602.01, ČSN EN 50131-1 Požadavek* Předpis/čl./kap. Montážní návod, značení výrobku, ČSN EN 50131-1 kap. 14, 15 dokumentace a uživatelské podmínky NIJ-SDT-0602.01 kap. 2.9 Definice zkušebních míst a podmínek zkoušení NIJ-SDT-0602.01 kap. 3 čl. 3.1 až 3.5 Zkušební postupy NIJ-SDT-0602.01 kap. 4 Rozměrné předměty NIJ-SDT-0602.01 4.1, 5.1 Předměty střední velikosti NIJ-SDT-0602.01 4.2, 5.2 Malé předměty NIJ-SDT-0602.01 4.3, 5.3 Detekční citlivost- rozlišení NIJ-SDT-0602.01 2.3.1, 2.3.2, 2.3.4, 3.2 Funkční požadavky NIJ-SDT-0602.01 2.6 Zkouška funkce v blízkosti kovových panelů NIJ-SDT-0602.01 3.4 Zkouška poplachové indikace NIJ-SDT-0602.01 3.3 Zkouška neškodnými předměty NIJ-SDT-0602.01 5.4 Definice zkušebních předmětů NIJ-SDT-0602.01 kap. 5
66
Příloha č. 7
Vlivy okolního prostředí
ČSN EN 50130-4
ČSN EN 50130-5
Dle: ČSN EN 50130-4, ČSN EN 50130-5, ČSN EN 55022 Typ zkoušky vlivu prostředí, odolnosti Třída prostředí Předpis/kap. proti rušení a měření vyzařovaného I II III IV (vedeného) rušení Suché teplo (provozní) 8 • • • • Chlad (provozní) 10 • • • • Vlhké teplo, konstantní (provozní) 12 • Vlhké teplo, cyklické (provozní) 14 • • • Vnik vody (provozní) 16 (IPX-2) • Vnik vody (provozní) 16 (IPX-4) • Ráz (provozní) 20 • • • • Vibrace, sinusové (provozní) 22 • • • • Změny síťového napájecího napětí 7 • • • • Poklesy a krátkodobá přerušení síťového 8 • • • • napájecího napětí Elektrostatický výboj 9 • • • • Rušení vysokofrekvenčním elektromagnetickým 10 • • • • polem Rušení indukované elektromagnetickými poli 11 • • • • Rychlé přechodové děje 12 • • • • Rázový impuls 13 • • • • Rušivé napětí na síťových svorkách ČSN EN 55022 • • • • třída B, kap. 5 Charakteristiky rádiového rušení ČSN EN 55022 • • • • třída B, kap. 6 • - Zkouška musí být provedena
Sestava zkoušeného výrobku:
Požadavky na základní parametry – údaje, identifikace, použití atd. Požadavek - údaj - výrobce - označení výrobku – typ – kategorie použití – stupeň zabezpečení třída + norma - kontrola počtu efektivních kombinací – prohlášení výrobce - kontrola omezujících parametrů – připojovací rozměry, kombinace provedení, modifikace, atd. - speciální funkce – záznamy - konstrukční údaje - další označení, údaje dle výrobce
67
Poznámka
Příloha č. 8
Příloha č. 8: Zařízení fyzického ničení nosičů informací – písm. h) § 30 zákona
Zařízení fyzického ničení nosičů informací (NNI)
Výstup
Certifikát shody podle certifikačního postupu NBÚ Podle vyhlášky č. 528/2005 Sb. příloha č. 1 – hodnocení zařízení fyzického ničení nosičů informací. Podle vyhlášky č. 528/2005 Sb. příloha č. 1 – hodnocení zařízení fyzického ničení nosičů dat.
Typ 1 - 4 Typ PC, PC1
Požadavky pro jednotlivé typy Předpis - článek
Požadavek Typ 4*
vyhláška č. 528/2005 Sb., příloha č. 1 - čl. 9.1
Typ 3*
vyhláška č. 528/2005 Sb., příloha č. 1 - čl. 9.2
Typ 2*
vyhláška č. 528/2005 Sb., příloha č. 1 - čl. 9.3
Typ 1*
vyhláška č. 528/2005 Sb., příloha č. 1 - čl. 9.4
Typ PC
vyhláška č. 528/2005 Sb., příloha č. 1 - čl. 13.2.4
Typ PC1
vyhláška č. 528/2005 Sb., příloha č. 1 - čl. 13.2.5
* Požadavky pro provádění zkoušek viz DIN 32757-1:1995 kap. 6
Požadavky na základní parametry – údaje, identifikace, použití atd. Požadavek - údaj
Poznámka
- výrobce - označení výrobku – typ – kategorie použití – stupeň zabezpečení třída + norma - speciální funkce - konstrukční údaje - další označení, údaje dle výrobce
68
Příloha č. 9
Příloha č. 9: Zařízení proti pasivnímu a aktivnímu odposlechu utajované informace - písm. i) § 30 zákona
Zařízení proti pasivnímu a aktivnímu odposlechu utajované informace Pro posuzování zařízení proti pasivnímu a aktivnímu odposlechu utajované informace je stanoven následující metodický postup zahrnující šumové generátory, akustické budiče, radiové analyzátory a detektory aktivní mobilní a rádiové komunikace.
Šumové generátory Zkouška vyzářeného akustického spektra a maskovací účinnosti a) spektrální charakteristika Spektrální charakteristika výstupního napětí se musí pohybovat v mezích ohraničených horní mezní hodnotou H a dolní mezní hodnotou L. Měření se provádí pro maximální zatížení výstupu tak, jak stanoví výrobce. Pokud má generátor více výstupu, provádí se měření na všech výstupech, přičemž všechny výstupy jsou současně zatíženy maximální zátěží. Je přípustné přepínání výstupního výkonu v několika stupních. Meze spektrální charakteristiky jsou uvedeny níže:
Horní mez H
Dolní mez L
Frekvence [kHz]
Útlum [dB/1V]
0-5
+10
5-10
+10 až -10
10-20
-10
0-5
-20
5-10
-20 až -40
10-20
-40 až -50
b) Zkouška maskovací účinnosti Zkouška maskovací účinnosti se provádí na vybraných zkušebních kmitočtech. Na pomocnou okenní tabuli se upevní ve vzdálenosti 0,5 m měrný piezo snímač a maskovací měřič. Měrný snímač se vybudí akustickou vazbou přes reproduktor, přičemž nárůst napětí na měrném snímači nad hlukem pozadí je pro zkušební kmitočty uveden v následující tabulce. Po vybuzení měrného snímače se zapne ochranný šumový generátor. Na spektrální charakteristice nesmí být indikovatelný signál odpovídající zkušebnímu kmitočtu.
69
Příloha č. 9 Zkušební kmitočet [kHz]
Nárůst napětí na měrném snímači [dB]
0,5
15
1
20
2
20
4
20
6
20
Zkouška
Norma
Předepsané údaje na výrobku
ČSN EN 50131-1 kap. 14
Požadavky na průvodní dokumentaci
ČSN EN 50131-1 kap. 15
Činnost zařízení napájecího napětí Činnost zařízení při poklesech a přerušení napájení Elektrostatickým výbojem
ČSN EN 50131-2-2 čl. 6.8.2
ČSN EN 50130-4, kap. 9, ČSN EN 61000-4-2
Vf elmag polem
ČSN EN 50130-4, kap. 10, ČSN EN 61000-4-3
Rychlými přechodovými jevy Zkouška odolnosti zařízení proti indukovanému vf poli Vyzářené akustické spektrum a maskovací účinnost Zkouška charakteristiky rádiového rušení
ČSN EN 50130-4, kap. 12, ČSN EN 61000-4-4
ČSN EN50131-2-2 čl. 6.8.3 – 6.8.5
ČSN EN 61000-4-6 Vlastní metodika akreditované zkušebny ČSN EN 55022, kap. 5 a 6
Akustické budiče Zkouška maskovací účinnosti Zkouška maskovací účinnosti se provádí na vybraných zkušebních kmitočtech. Na jednu stranu příčkové zdi se umístí akustický budič napájený ze šumového generátoru a na druhou stranu zdi se přilepí měrné piezosnímače. Ze strany akustického budiče se ve vzdálenosti 3 m od zdi umístí pomocný reproduktor, orientovaný svou osou na střed zdi. Tento reproduktor je napájený z výkonového zesilovače. Reproduktor se vybudí tak, aby ve středu zdi bylo dosaženo akustické úrovně dle níže uvedené tabulky. Tato hodnota odpovídá hlasitému hovoru. Po vybuzení reproduktoru se zapne ochranný šumový generátor.
Pro dosažení maskovací účinnosti akustického signálu (hlasitého hovoru) v chráněném prostoru a tím znemožnění odposlechu, nesmí být na spektrální charakteristice měrného piezosnímače indikovatelný akustický signál vybuzený reproduktorem. Zkušební kmitočet [kHz] 0,5 1 2
Nárůst napětí na měrném snímači [dB] 50 50 40
70
Příloha č. 9
Zkouška Kontroly průvodní dokumentace Kontrola značení Činnost zařízení napájecího napětí Elektrostatickým výbojem Vf elmag polem Rychlými přechodovými jevy Vyzářené akustické spektrum a maskovací účinnost
Norma ČSN EN 50131-1 kap. 14 ČSN EN 50131-1 kap. 15 ČSN EN 50131-2-2 čl. 6.8.2 ČSN EN 50130-4, kap. 9, ČSN EN 61000-4-2 ČSN EN 50130-4, kap. 10, ČSN EN 61000-4-3 ČSN EN 50130-4, kap. 12, ČSN EN 61000-4-4 Vlastní metodika akreditované zkušebny
Detektory aktivní mobilní a rádiové komunikace Zkouška detektorů lokálních vf odposlechových zařízení. Zkouška má prokázat dostatečnou citlivost při indikaci aktivní mobilní a radiové komunikace
při
určení
charakteru
signálu.
Slouží
k ověření
preventivní
ochrany
definovaného chráněného prostoru a možnosti indikace vysílačů s digitální modulací.
a) zkouška citlivosti detektoru vf pole Zkouška pro detektory I třídy se provádí v pásmu 80 – 1000 MHz. Zkouška indikace detektoru při trvalé intenzitě elmag pozadí pro intenzity pole +20dBµV/m nad minimální citlivostí.
b) zkouška rozlišení druhu vf signálu Tento detektor (EUT) musí rozlišovat následující signály: a) signál z mobilních telefonů b) signál z radiových lokálních zařízení Požadované hodnoty citlivosti pro detektory třídy I pro vzdálenost od EUT 1 metr: Frekvence [kHz] 80-200
Intenzita pole pro min. citlivost EUT [dBµV/m] 90-70
Intenzita pole pro max. citlivost EUT [dBµV/m] 60-40
200-600
70
40
600-1000
70-90
40-60
Pozn.: Zkoušku možno provádět i mimo prostor bezodrazové komory. V protokolu o zkoušce musejí být uvedeny všechny signály elmag. pozadí s intenzitou pole nad 70 dBµV/m. Zkušební kmitočty: 100, 200, 300, 400, 500, 600, 700, 800, 900, a 1000 MHz.
V případě, že není možné provést zkoušku v bezodrazové komoře je přípustná z důvodů rušivého pozadí odchylka od uvedených zkušebních kmitočtů o ± 20 MHz.
71
Příloha č. 9 c) zkouška rozlišení druhu vf signálu Zkouška se provádí na výše uvedených zkušebních kmitočtech a to pro střední hodnotu citlivosti detektoru a to pro následující druhy signálu: a) modulovaný vf signál, kmitočtová modulace, zdvih 20 kHz musí být indikovatelný modulační signál b) modulovaný vf signál, amplitudová modulace 80 % musí být indikovatelný modulační signál c) signál z mobilních telefonů signál je indikován jako melodie nebo nastavitelný zvukový alarm
Zkouška
Norma
Kontroly průvodní dokumentace
ČSN EN 50131-1 kap. 14
Elektrostatickým výbojem
ČSN EN 50130-4, kap. 9, ČSN EN 61000-4-2
Vf elmag polem
ČSN EN 50130-4, kap. 10, ČSN EN 61000-4-3
Rychlými Rušení indukovaným vf polem
ČSN EN 50130-4, kap. 11, ČSN EN 61000-4-6
Rychlými přechodovými jevy
ČSN EN 50130-4, kap. 12, ČSN EN 61000-4-4
Detektorů lokálních vf odposlech. zařízení
Vlastní metodika akreditované zkušebny
Charakteristiky rádiového rušení
ČSN EN 55022, kap. 5 a 6
Radiové analyzátory Zkouška
Norma
Předepsané údaje na výrobku
ČSN EN 50131-1 kap. 14
Požadavky na průvodní dokumentaci
ČSN EN 50131-1 kap. 15
Činnost zařízení změně napájecího napětí Činnost zařízení při poklesech a přerušení napájení Funkce zařízení při klesání napájecího napětí Elektrostatickým výbojem
ČSN EN 50130-4, kap. 5, 6, 7
Vf elmag polem
ČSN EN 50130-4, kap. 10, ČSN EN 61000-4-3
Rychlými přechodovými jevy Zkouška odolnosti zařízení proti indukovanému vf poli Zkouška charakteristiky rádiového rušení
ČSN EN 50130-4, kap. 12, ČSN EN 61000-4-4
ČSN EN50131-2-2 čl. 6.8.3 – 6.8.5 ČSN EN 50131-2-2 čl. 6.8.2 ČSN EN 50130-4, kap. 9, ČSN EN 61000-4-2
ČSN EN 61000-4-6 ČSN EN 55022, kap. 5 a 6
72