IDTM
Myčka Návod k instalaci a použití
IDTM
Myčka nádobí Návod k instalaci a použití
Vážený zákazníku, děkujeme Vám, že jste si zakoupil výrobek společnosti MERLONI Elettrodomestici, spa. Při vybírání přístroje pečlivě zvažte, jaké činnosti a funkce od přístroje požadujete. To, že výrobek nevyhovuje Vaším pozdějším nárokům, nemůže být důvodem k reklamaci. Před prvním použitím si pozorně přečtěte přiložený český návod, který dodává firma Merloni Elettrodomestici, spa ke svým dováženým výrobkům a důsledně se jím řiďte. Veškeré výrobky slouží pro domácí použití. Pro profesionální použití jsou určeny výrobky specializovaných výrobců. Všechny doklady o koupi a eventuálních opravách Vašeho výrobku pečlivě uschovejte pro poskytnutí maximálně kvalitního záručního i pozáručního servisu. Dodržování těchto zásad, povede k Vaší spokojenosti. V případě jejich nerespektování však nemůžeme uznat případnou reklamaci. Doporučujeme Vám po dobu záruční lhůty uchovat původní obaly k výrobku. Než budete kontaktovat servisní středisko, pečlivě prostudujte návod na obsluhu a záruční podmínky uvedené v záručním listě. Pokud bude při opravě zjištěno, že závada nespadá do záruky, uhradí vzniklé náklady zákazník. Vážený zákazníku, návod který jste obdržel k našemu výrobku, vychází z všeobecného návodu pro celou výrobkovou řadu. Z tohoto důvodu může dojít k situaci, že některé funkce, ovládací prvky a příslušenství nejsou určeny pro Váš výrobek. Děkujeme za pochopení. Aby byla zajištěna řádná ÚČINNOST a BEZPEČNOST tohoto zařízení, doporučujeme Vám: • Kontaktovat servisní středisku, které je autorizováno výrobcem. • Vždy používat originální náhradní díly.
2
Návod k obsluze MYČKA NÁDOBÍ Obsah Instalace, 4-5 CZ
Umístění a vyrovnání Připojení k přívodu vody a elektrické připojení Technické údaje
Popis spotřebiče, 6 Celkový náhled Ovládací panel
Vložení nádobí do košíků, 7 Spodní košík Košík na příbory Horní košík
IDTM
Zapnutí a použití, 8 Zapnutí myčky Přidání mycího prostředku Možnosti omývání
Mycí cykly, 9 Tabulka mycích cyklů
Leštící přípravek a změkčovací sůl, 10 Přidání leštícího přípravku Přidání změkčovací soli
Péče a údržba, 11 Uzavření přívodu vody a přívodu elektřiny Vyčištění myčky Zamezení nepříjemných pachů Vyčištění stříkacích ramen Čištění filtrů Nepoužívání spotřebiče po delší dobu
Bezpečnostní opatření a pokyny, 12 Všeobecné bezpečnostní opatření Likvidace Úspora energie a ochrana životního prostředí
Řešení problémů, 13
3
Instalace ! Tento manuál uložte na bezpečné místo. Pokud budete zařízení prodávat nebo stěhovat, dbejte na to, aby byl tento manuál vždy s přístrojem tak, aby z něj mohl nový majitel získat informace. ! Tento návod k použití se přečtěte pečlivě; obsahuje důležité informace, které se týkají bezpečné instalace, použití a údržbě tohoto spotřebiče. ! Pokud je přístroj z jakýchkoliv důvodů přenášen, snažte se ho udržet ve vodorovné poloze, pouze v případě, že je to opravdu nezbytné jej můžete položit na zadní stranu.
Umístění a vyrovnání 1. Spotřebič vybalte a zkontrolujte, zda – li nebyl během přepravy jakkoli poškozen. Pokud ano, kontaktujte prodejce a nepokračujte v instalaci. 2. Myčku umístěte tak, aby boční stěny nebo zadní panel byly v kontaktu se sousedními skříněmi nebo se zdí. Tento spotřebič může být také umístěn pod pracovní desku. (viz Montážní list). 3. Myčku umístěte na rovnou a pevnou podlahu. Pokud je podlaha nerovná, můžete pomocí předních nožek myčku vyrovnat do horizontální polohy (úhel naklonění nesmí přesáhnout dva stupně). Pokud je přístroj správně vyrovnán, je stabilnější a je méně náchylný na posouvání při chodu nebo způsobuje menší vibrace a hluk při chodu.
Připojení vody a elektřiny ! Připojení vody a elektřiny by mělo být prováděno pouze kvalifikovaným odborníkem. ! Myčka nádobí by neměla stát na hadici přívodu vody nebo na kabelu přívodu elektřiny. Přívodní hadice (A), odtoková hadice (B) a kabel napájení elektrickým proudem by měli být umístěny vlevo nebo vpravo od přístroje tak, aby umožnili co nejlepší možnou instalaci přístroje (viz obrázek).
Připojení hadice pro přívod vody • Aby byl vhodně připojen přívod studené vody: dříve než připevníte hadici, pusťte vodu, dokud nebude perfektně čistá, aby se zabránilo zanesení přístroje případnými nečistotami ve vodě; po provedení tohoto úkonu, našroubujte přívodní hadici těsně na 3/4 plynovou přípojku se závitem. • Aby byl vhodně připojen přívod teplé vody: Vaše myčka může být zásobena teplou vodou z hlavního přívodu (pokud máte centrální tepelný systém s topením), která by neměla přesáhnout teplotu 60 °C. Našroubujte hadice na přípojku jak je popsáno u připojení studené vody. ! Pokud přívodní hadice není dost dlouhá, kontaktujte specializovanou prodejnu nebo autorizovaného technika (viz Technická podpora). ! Tlak vody musí být v rozmezí, které stanovených v tabulce technických údajů (viz níže) ! Hadice by se neměla lámat nebo stlačovat. Ochrana před vytopením Pro zabránění vytopení, je myčka: - vybavena systémem, který zablokuje přívod vody v případě anomálií nebo prosakování z vnitřku myčky. - vybavena bezpečnostním zařízením pro zastavení vody*. Jinými slovy, má přívodní hadici, která se skládá z transparentní hadice vně a červené hadice uvnitř: Obě hadice mohou vydržet extrémně vysoký tlak. Jestliže vnitřní hadice praskne, vnější hadice se zbarví do světle červena a voda dále proudí v ní. Toto zabrání jakýmkoliv prosáknutím. ! Je velmi důležitá pravidelná kontrola vnější hadice: pokud je světle červená, musí být vyměněna autorizovaným technikem, tak brzy jak jen to je možné (viz Technická podpora).
A
60 83
120
168
121
100
148
B * Dostupné pouze u vybraných modelů.
4
Připojení odpadní hadice
Doporučení ohledně prvního mycího cyklu
Připojte odpadní hadici, (bez zakřivení či zalomení) na odpadní potrubí nebo k odpadu o minimálním průměru 4 cm. Popřípadě ji můžete přehodit přes okraj umyvadla nebo vany; volný konec hadice nesmí zůstat ponořený ve vodě.
Po nainstalování myčky, těsně než začnete první prací cyklus, naplňte kompletně zásobník soli vodou a přidejte asi 2 kg soli (viz Leštící přípravek a změkčovací sůl). Voda by měla přetéci, to je normální a není to problém. Je také normální, že indikátor MÁLO SOLI* bliká ještě pár cyklů poté co sůl již byla doplněna.
A
Speciální plastické zakřivení* usnadňuje nalezení nejvhodnějšího umístění: připevněte ohyb bezpečně ke zdi tak, aby se hadice nemohla pohnout a volně vystřikovat špinavou vodu. Část hadice označená písmenem (A) by měla být v rozmezí 40 – 100 cm nad zemí (viz obrázek).
! Doporučujeme nepoužívat prodlužovací hadice. Elektrické připojení
Technické údaje Rozměry
šířka 60 cm výška 85 cm hloubka 60 cm
Kapacita
12 standardních souprav nádobí
Tlak připojení vody
30 kPa ÷ 1 MPa (0.3 ÷ 10 barů) 4,3 psí –145 psí
Elektrické připojení
Viz datový štítek myčky
Maximální příkon
Viz datový štítek myčky
Pojistka
Viz datový štítek myčky
Před zapojením do elektrické sítě se ujistěte, že: • síťová zásuvka je opatřena uzemněním a odpovídá platným předpisům. • síťová zásuvka může být zatížena maximálním příkonem pračky uvedeným na datovém štítku umístěném na vnitřní straně dvířek (viz Popis spotřebiče); • napětí elektrické sítě odpovídá údajům vyznačeným na datovém štítku na vnitřní straně dvířek; • zástrčka se hodí do zásuvky. Pokud tomu tak není zeptejte se autorizovaného technika na výměnu zástrčky (viz Technická podpora); nepoužívejte prodlužovací kabely či rozdvojky. ! Zásuvka a elektrický kabel by měli být po instalování myčky snadno dostupní. ! Kabel nesmí být ohnutý nebo stlačený. ! Kabel musí být pravidelně kontrolován a smí být vyměněn pouze autorizovaným odborníkem (viz Technická podpora).
Tato myčka vyhovuje následujícím směrnicím Evropského Hospodářského společenství: - 72/23/CEE z 19/02/73 (Nízké napětí) a následným úpravám - 89/336/CEE z 03/05/89 ( Elektromagnetická kompatibilita) a následným úpravám - 97/17/EC (označení) - 2002/96/CE (WEEE)
! Výrobce se zříká jakékoliv odpovědnosti, pokud nebudou tato opatření a pravidla respektována.
* Dostupné pouze u vybraných modelů
5
Popis zařízení Celkový pohled
!
"
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11.
Horní košík Horní postřikové rameno Sklápěcí přihrádka Seřizování výšky košíku Dolní košík Dolní postřikové rameno Košík na příbory Mycí filtr Dávkovač soli Dávkovač čistícího a leštícího prostředku Datový štítek
#
$
%
'
&
Ovládací panel Kontrolka ZBÝVAJÍCÍ ČAS
Kontrolka* 3V1
Kontrolka* MÁLO SOLI
Tlačítko START/RESET
Kontrolka MYCÍ PROGRAM V CHODU Kontrolka MYCÍ PROGRAM Tlačítko* DOKONČEN 3V1
Kontrolka* MÁLO LEŠTÍCÍHO PROSTŘEDKU
Tlačítko ON/OFF
Ovládací knoflík AUTOMATICKÝ MYCÍ CYKLUS DÉLKA MYCÍHO CYKLU ČASOVAČ
* Dostupné pouze u vybraných modelů 6
Kontrolka ON/OFF
Naplnění košíků ! Před naplněním košíku, odstraňte veškeré zbytky jídla z nádobí, vylijte vodu z připálených pánví a z nádobí, které jste dali namočit a vylijte zbytky tekutin z hrnků a skleniček. Po naplnění myčky zkontrolujte, zda může postřiková ramena volně rotovat.
kolečka nejsou na místě a zavřete zarážku (viz obrázek).
Spodní košík Zde umístěte špatně omyvatelné nádobí, využijte Příklady uložení jako návod a sklápěcí podpěrku* tam kde je potřeba. • Talíře a pokličky: umisťujte na strany košíku. • Pánve a mísy: umisťujte vždy dnem vzhůru. • Velmi hluboké nádobí: umisťujte pod úhlem. Kvůli zajištění dobrého mytí a sušení je povrch dolního košíku více nerovný než povrch horního košíku.
Příklady naplnění horního koše
Košík na příbory Typ košíku na příbory se liší podle modelu myčky. ! Nože a všechny ostatní ostré kuchyňské potřeby umísťujte do košíku ostřím dolů.
Pro rozdělení centrálního koše* na dvě poloviny: vytáhněte držadlo. Dvě oddělitelné postraní přihrádky* můžete zavěsit na horní nebo dolní koš. Dvě mřížky* můžete vložit do koše a oddělit tak různé druhy příborů: umístěte jednotlivé příbory do odpovídajících oddělení s držadly na dně.
Horní košík Tento koš naplňte křehkým a lehkým nádobím: skleničkami, hrníčky, podšálky, malými salátovými miskami, pánvemi, a malými pánvičkami, které nejsou příliš znečištěné. Přihlédněte k návodu v kapitole Příklady uložení. • Lehké nádobí: umístěte jej tak, aby s nimi nepohnul tryskající proud vody. • Hrnky a pohárky: umístěte je na sklápěcí přihrádku**. • Dlouhé ostré nože a jiné kuchyňské náčiní: umístěte je na sklápěcí přihrádku**. Nastavení výšky horního koše Kvůli usnadnění naplnění nádobím můžete horní koš posouvat nahoru 1 či dolů. Otevřete levou a pravou 2 zarážku posuvných kolejnic a vytáhněte horní koš: posuňte jej nahoru nebo dolů dle potřeby, 3 4 zasuňte jej do kolejnic dokud přední
Příklady naplnění dolního koše
Oddělitelné části** Zvláštní oddělitelné části můžete použít pro umístění hrnků a pohárů. Lžíce, vidličky a nože mohou být umístěny do otvorů odděleně. Skleničky na víno můžete zaháknout do mezer v okraji této pomůcky. Věci, které byste neměli umývat v myčce • Dřevěné předměty, předměty s držadly ze dřeva či z rohu nebo předměty s přilepenými částmi. • Předměty z hliníku, mědi, mosazi, cínu nebo pocínované. • Předměty z plastu, který není odolný proti vyšším teplotám. • Starožitný nebo ručně malovaný porcelán. • Starožitné stříbro. Jiné stříbro lze v myčce mýt, ale za použití jemného pracího cyklu. Zajistěte, aby se stříbro nedostalo do kontaktu s jinými kovy. ! Pokud kupujete nádobí a příbory doporučujeme, abyste se ujistili, že jej můžete mýt v myčce. Mytí držadel* Pro umytí držadel horního a dolního koše: odstraňte dvě upevňovací svorky, vytáhněte držadla a opláchněte je pod tekoucí vodou, pak je připevněte zpět za použití těch samých svorek.
* Dostupné pouze u vybraných modelů. ** Počet a pozice mohou být variabilní. 7
Zapnutí a použití Zapnutí myčky 1. Zapněte přívod vody 2. Zmáčkněte tlačítko ON/OFF : rozsvítí se indikátor. 3. Otevřete dvířka a vložte přijatelné množství mycího prostředku (viz níže). 4. Naplňte košíky (viz Naplnění košíků) a zavřete dvířka. 5. Navolte konec mycího cyklu otočením ovládacího knoflíku na hodnoty: • 30 min., 60 min., 90 min., 3h*, 6h*, 9h* (viz kapitola Opožděný start), nastavte typ umístění nádobí a stupeň zašpinění (viz tabulka mycích cyklů) • Automatický mycí cyklus (auto4you): umožní vám dosáhnout nejlepšího umytí a osušení v nejkratším možném čase (viz tabulka mycích cyklů). 6. Nastavte způsob mytí (viz niže). 7. Zapněte cyklus stisknutím tlačítka START/RESET: myčka potvrdí zahájení mytí pípnutím. Rozsvítí se kontrolka MYCÍ PROGRAM V CHODU. 8. Během mytí můžete sledovat kolik času ještě zbývá díky kontrolce ZBÝVAJÍCÍ ČAS: • 20 minut do konce mycího cyklu • 10 minut do konce mycího cyklu 9. Na konci pracího cyklu uslyšíte tři krátká pípnutí a začne blikat kontrolka MYCÍ PROGRAM DOKONČEN. 10.Vypněte přístroj pomocí tlačítka ON/OFF, zavřete přívod vody a vypněte přístroj ze zásuvky. 11.Otevřete dvířka a počkejte pár minut než vyndáte nádobí, abyste se nespálili. Vyprázdněte koše. Začněte se spodním. Úprava mycího cyklu za chodu Pokud jste špatně nastavili mycí cyklus, můžete ho změnit během jedné minuty od okamžiku, kdy se rozsvítí kontrolka MYCÍ PROGRAM V CHODU: stiskněte a držte tlačítko START/ RESET po dobu 4 sekund. Uslyšíte jedno dlouhé a tři krátká pípnutí. Přístroj pak znovu spustíte pomocí tlačítka START/ RESET. Přidání dalšího nádobí Stiskněte tlačítko ON/OFF a otevřete dvířka, dávejte přitom pozor na unikající horkou páru a vložte další nádobí do myčky. Poté znovu stiskněte tlačítko ON/OFF: cyklus začne od místa kde byl přerušen. Náhodná přerušení Pokud za běhu otevřete dvířka či dojde k přerušení dodávky proudu, cyklus se přeruší a po jejich zavření či obnovení dodávky proudu začne znovu od bodu přerušení.
Naplnění mycího prostředku D
Úspěšné umytí také závisí na správném množství mycího prostředku doporučeného výrobcem. Překročení doporučeného množství neovlivní efektivnost mytí a navíc znečišťuje prostředí. přihrádka A A: Mycí prostředek C přihrádka B B: Prostředek pro předmytí 1. Otevřete kryt C stisknutím tlačítka D. 2. Vložte správné množství mycího prostředku podle tabulky mycích cyklů: A
B
• pro práškové mycí prostředky použijte přihrádky A a B • pro mycí prostředky v tabletách použijte přihrádku A a dno myčky; např. pokud cyklus potřebuje 1 tabletu vložte ji do přihrádky A a zavřete víko; pokud potřebuje dvě tablety, druhou vložte na dno myčky. 3. Odstraňte zbytky mycího prostředku z rohů přihrádek a zavřete kryt dokud nezacvakne.
Možnosti mytí Opožděný start Myčka umožňuje uživateli nastavit denní dobu, kdy má mytí proběhnout. Abyste dosáhli nejlepšího výkonu, můžete zvolit mycí cyklus 3, 6 nebo 9 hodin nebo AUTOMATICKÝ MYCÍ CYKLUS. Pamatujte, že. • je-li nastaven mycí cyklus 3h, myčka bude čekat 30 minut a potom 150 minut mýt nádobí. • je-li nastaven mycí cyklus 6h, myčka bude čekat 3 hodiny a 30 minut a potom 150 minut mýt nádobí. • je-li nastaven mycí cyklus 9h, myčka bude čekat 6 hodin a 30 minut a potom 150 minut mýt nádobí. Pro změnu nebo zrušení takto nastaveného mycího cyklu, stiskněte tlačítko START/RESET a po pípnutí můžete nastavit jiný mycí program. Mytí zahájíte opětovným stisknutím tlačítka START/RESET. Tlačítko 3v1* Pokud používáte multifunkční tablety (2-v-1, 3-v-1, 4-v-1), zmáčkněte tlačítko 3v1. Při použití tohoto tlačítka se celková doba mytí prodlouží přibližně o 10 minut. ! Toto tlačítko nemůže být použito spolu s 30 minutovým cyklem.
* Dostupné pouze u vybraných modelů.
8
Mycí cykly Tabulka mycích cyklů ! Myčky INDESIT jsou vybaveny automatickým systémem čištění filtrů, takže nemůže docházet k zanesení zbytky jídla. Tato funkce může prodloužit dobu trvání mycích cyklů.Je-li znečištění příliš velké, myčka se vypne (viz Řešení problémů Alarm ucpaného filtru.)
Instrukce pro zvolení mycího cyklu
Mycí prostředek (A) = přihrádka A (B) = přihrádka B
Mycí cyklus
Předmytí
Sušení
Trvání mycího cyklu (tolerance +/- 10 %)
Prášek
Tekutina
Tablety
30 min.
25 g (A)
25 ml (A)
-
30 min.
Cyklus vhodnýpro pánve a talíře s běžným stupněm zašpinění.
60 min.
30 g (A)
30 ml (A)
1 (A)
60 min.
Cyklus vhodnýpro nádobí s typickým každodenním zašpiněním, včetně sklenic.
90 min.
30 g (A)
30 ml (A)
1 (A)
25 g (A) 5 g (B)
25 ml (A) 5 ml (B)
1 (A)
Ekonomický a rychlý cyklus pro malé množství nádobí nebo pro mírně znečištěné talíře ihned po jejich použití. Může být použito (bez mycích prostředků) pro opláchnutí talířů, než naplníte myčku nádobím. Tento program nelze použít společně s funkcí tlačítka 3v1.
Ideální cyklus pro nádoby na smažení, omáčníky a jiného nádobí.Spotřeba vody a elektřiny je optimalizována).
•
•
90 min.
•
150 min.
automaticky
Poznámka Pro jednodušší odhad při dávkování mycího prostředku si zapamatujte: 1 lžíce = 15 gramů prášku = přibližně 15 ml tekutiny 1 lžička = 5 gramů prášku = přibližně 5 ml tekutiny 9
Leštící přípravek a změkčovací sůl ! Používejte pouze produkty, které byly navrženy speciálně pro myčky. Nepoužívejte stolní nebo technickou sůl. ! Pokud používáte multifunkční tablety (2-v-1, 3-v-1, 4-v-1) není nutné přidávat leštící prostředek, nicméně doporučujeme přidat sůl, obzvláště pokud žijete v prostředí s tvrdou nebo velmi tvrdou vodou. Pokud nepřidáte ani sůl ani leštící prostředek, automaticky budou blikat kontrolky MÁLO SOLI* a MÁLO LEŠTÍCÍHO PROSTŘEDKU*.
Naplnění leštícího prostředku Leštící prostředek usnadňuje nádobí uschnout, jelikož voda z povrchu stéká rychleji a nezanechává cesty nebo fleky. Měli byste naplnit zásobník leštícího prostředku: • vždy když kontrolka (H) signalizuje, že zásobník je prázdný. Svítící kontrolka: naplňte leštícím prostředkem; nesvítící kontrolka: není potřeba doplňovat leštící prostředek. • pokud bliká na panelu kontrolka MÁLO LEŠTÍCÍHO PROSTŘEDKU*;
H
F
G
1. Odstraňte spodní koš a odšroubujte víko zásobníku (proti směru hodinových ručiček). 2. Pouze pro první cyklus: naplňte zásobník až po okraj vodou. 3. Správně umístěte dodávanou nálevku ( viz obrázek ) a naplňte zásobník až po okraj (přibližně 2 kg); je normální, že se vylije trošku vody. 4. Odstraňte nálevku a pozůstatky soli a přišroubujte zpět natěsno víko, aby voda neprosakovala do dávkovače během mycích programů (toto by mohlo nenávratně poškodit systém změkčování vody). ! Pokud je sůl přidána, okamžitě zahajte prací cyklus, bez nádobí, abyste odstranili zbytky soli a zabránili tak korozi nádobí. Nastavení množství soli* Je možné nastavit množství soli v závislosti na tvrdosti vody ve Vašem prostředí (tuto informaci obdržíte od společnosti, která k Vám vodu dodává).
1. Otevřete přihrádku otáčením víka (G) proti směru hodinových ručiček. 2. Nasypte leštící prostředek a ujistěte se, že nepřetéká ze zásobníku. Pokud se tak stane, setřete ihned zbytky houbou. 3. Zašroubujte kryt zpět.
Přizpůsobení množství leštícího prostředku Pokud nejste spokojeni s výsledky mycího cyklu, měli byste přizpůsobit množství leštícího prostředku. Použijte šroubovák k otočení nastavení dávkovače na jednu ze 6. přednastavených možností (standardně je nastaveno na 4): • pokud jsou na nádobí bílé fleky nastavte dávkovač na nižší hodnotu (1-3). • pokud jsou na nádobí zbytky jídel či vody nastavte dávkovač na vyšší hodnotu (4-6). ! Pokud používáte multifunkční tablety (2-v-1, 3-v-1, 4-v-1) a chcete zlepšit výsledek sušení, naplňte zásobník a nastavte dávkovač na 2.
1. Odšroubujte víko zásobníku soli. 2. Šipku, kterou uvidíte (viz obrázek) otočte směrem k + nebo -, v závislosti na tvrdosti vody viz tabulka.
Tvrdost vody °dH
°fH
°mmol/l
0-10
0-17
0-1.7
Poloha
Spotřeba soli (g/program)
Počet programů (programy/2 kg)
/
0
/
10-25 18-44
1.8-4.4
„-“
20
60
25-50 45-89
4.5-8.9
STŘED
40
40
>8.9
„+“
60
25
>50
>89
Počáteční nastavení systému změkčování vody je na +. - Pokud používáte multifunkční tablety (2-v-1, 3-v-1, 4-v-1) naplňte zásobník soli a nastavte dávkovač na - ; pokud je tvrdost vody větší než 60 °fH, nastavte dávkovač na +.
Naplnění změkčovací soli Abyste dosáhli nejlepších možných výsledků mycích cyklů, zajistěte, aby zásobník nebyl nikdy prázdný. Změkčovací sůl zmenšuje tvrdost vody a tím zabraňuje usazování vodního kamene na nádobí. Zásobník soli je umístěn ve spodní části myčky (viz Popis myčky) a měl by být naplněn: • pokud nevidíte zelený plovák* když se podíváte na víko zásobníku soli; • pokud na panelu bliká kontrolka MÁLO SOLI*; • pokud Vaše myčka není vybavena ani plovákem ani kontrolkou: přibližně po 30 mycích cyklech; * Dostupné pouze u vybraných modelů. 10
Péče a údržba Odpojení vody a elektřiny
Čistění filtrů
• Vypněte vodu po každém mycím cyklu, abyste zabránili náhodnému prosáknutí vody.
Filtry odstraňují zbytky jídla z vody během mycích cyklů, je proto doporučeno je čistit, abyste dosáhli co nejlepšího mytí.
• Odpojte myčku od elektřiny pokaždé, když provádíte čištění nebo údržbu.
! Čistěte filtry pravidelně.
Čištění myčky
! Po vyčistění zkontrolujte, zda byly filtry správně zasazeny zpět. ! Myčka by se neměla bez filtrů používat.
• Externí povrch myčky a panel čistěte pomocí hadříku navlhčeného teplou mýdlovou vodou. Nepoužívejte rozpouštědla nebo brusné prostředky.
1. Odstraňte filtr vytáhnutím držadla nahoru. 2. Vyčistěte filtry:
• Jakékoliv skvrny uvnitř myčky odstraňujte pomocí hadříku navlhčeného ve vodě s octem.
• po každém mycím cyklu odstraňte tekoucí vodou.největší nečistoty z polokruhové plochy A a skla B (ty můžete odstranit vytažením držadla).
C 1
Zamezení vzniku nepříjemných zápachů
2
• Vždy nechávejte dvířka přístroje pootevřené, abyste zabránili vzniku a uzavření vlhkosti uvnitř přístroje.
A B
• Pravidelně čistěte uzávěry okolo dvířek a zásobníky na mycí prostředky s použitím vlhké houbičky. Zabráníte zachycení zbytků jídel v uzávěrech, což je hlavní příčina vzniku nepříjemných zápachů.
C
B
Čistění ostřikovacího ramene Zbytky jídla mohou zablokovat otvory ostřikovacho ramene a zabránit tak stříkání vody. Proto doporučujeme, abyste je čas od času zkontrolovali a případně očistili pomocí nekovového kartáče.
A
• všechny díly filtru byste měli vyčistit alespoň jednou do měsíce: to zahrnuje polokruhovou část A, sklo B a cylindr C (ten můžete odstranit tak, že jím otočíte proti v směru hodinových ručiček). K čistění použijte malý nekovový kartáček.
3. Složte filtr dohromady a vraťte jej zpět na jeho místo, sledujte přitom kroky 1 a 2 jak to vidíte na obrázku, dokud nezaklapne na místo.
Pokud myčku nepoužíváte delší dobu • Spusťte mycí program, když je myčka prázdná. • Zastavte přívod vody a vypojte myčku z přívodu elektřiny. • Nechte dvířka myčky pootevřené
11
Opatření a doporučení ! Přístroj byl navržen a sestrojen aby splňoval mezinárodní bezpečnostní standardy. Následující informace jsou tu pro Vaše bezpečí a měli byste si je proto důkladně prostudovat.
Zákazníci by se měli spojit s místními úřady nebo prodejci, kde získají podrobnější informace o likvidaci přístroje.
Hlavní bezpečnostní zásady
Úspora energie a respektování životního prostředí
• Přístroj byl navržen pro domácí použití pouze a není proto vhodný pro komerční nebo technické používání. • Přístroj by měli používat pouze dospělí lidé a to s ohledem na tento návod k obsluze. • Přístroj nesmí být nainstalován ve venkovních prostorách a to ani pod krytem. Je extrémně nebezpečné vystavovat jej dešti nebo bouřkám. • Nedotýkejte se přístroje bosí. • Při odpojování přístroje od elektrického proudu, vždy tahejte za koncovku, nikdy ne za kabel. • Kohoutek přívodu vody musí být uzavřen a přístroj musí být odpojen ze zásuvky dříve, než začnete s jeho čištěním a údržbou. • Pokud se přístroj porouchá, za žádných okolností se nedotýkejte vnitřních částí a nezkoušejte jej opravovat sami. • Nikdy se nedotýkejte topného tělesa. • Nikdy se neopírejte nebo neseďte na otevřených dvířkách, mohlo by to způsobit, že se myčka převrhne. • Udržujte mycí a leštící prostředky mimo dosah dětí. • Obal by nikdy neměl sloužit jako hračka: mohl by způsobit udušení.
Likvidace starých elektrických zařízení Evropská směrnice 2002/96/EC o elektrickém a elektronickém odpadu (WEEE) vyžaduje, aby staré elektrické domácí spotřebiče nebyly likvidovány klasickou cestou. Staré spotřebiče musí být shromažďovány odděleně pro vhodnou recyklaci částí a materiálu a zredukování dopadu na lidské zdraví a prostředí. Symbol přeškrtnuté popelnice na kolečkách Vám má připomenout, že pokud chcete přístroj zlikvidovat, musíte to provést oddělené od ostatního odpadu.
Úspora vody a energie • Mycí program zahajujte pouze tehdy, pokud je myčka plná. Pokud čekáte na zaplnění, předcházejte nepříjemným zápachům pomocí namáčecího cyklu (viz Mycí cykly). • Používejte mycí cykly vhodné pro dané typy nádobí a druhu znečistění dle tabulky mycích cyklů: - pro nádobí s normálním znečištěním používejte mycí cyklus EKO, který garantuje nízkou spotřebu vody a energie. - pokud je méně špinavého nádobí než obvykle použijte cyklus polovičního zaplnění (viz Spuštění a použití). • Pokud Váš dodavatel elektřiny mívá časy kdy spotřeba stojí méně, myjte nádobí v těchto dobách. Tlačítko opožděného startu* (viz Spuštění a použití) Vám pomůže vhodně mytí načasovat. Mycí prostředky bez fosfátů a chlóru, obsahují enzymy • Velmi doporučujeme používat mycí prostředky bez fosfátů a chlóru, jelikož jsou šetrné k životnímu prostředí. • Enzymy jsou nejúčinnější hlavně při teplotách okolo 50 °C, z toho vplývá že jsou vhodnější pro mycí cykly s nižšími teplotami. Dosáhnete tak stejných výsledků, jako při použití běžných mycích přípravků za teploty okolo 65 °C. • Abyste zabránili zbytečnému plýtvání mycích prostředků, používejte je v množství doporučeném výrobcem pro určitou tvrdost vody, určitém množství nádobí a množství soli. Přestože je mycí prostředek biologicky rozložitelný, může mít negativní účinky na životní prostředí.
* Dostupné pouze u vybraných modelů. 12
Řešení problémů Kdykoliv přístroj nefunguje správně, vyzkoušejte postupy z následujícího seznamu, než zavoláte nejbližší servisní středisko.
Porucha:
Možné příčiny/Řešení
Myčka se nechce spustit..
• Přívodní kabel nebyl zasunut správně do zásuvky nebo je výpadek proudu. • Dvířka myčky nejsou řádně uzavřeny. • Byl zadán odložený start (viz Spuštění a použití)
Do myčky nepřitéká voda.
• Hlavní přívod vody nedodává vodu. • Přívodní hadice je ohnutá (viz Instalace)...
Z myčky nevytéká voda.
• • • •
Myčka vydává nadměrný hluk.
• Nádobí drncá o sebe nebo o ostřikovací rameno.
Nádobí a skleničky jsou pokryty bílým filmem nebo zbytky vodního kamene.
• Množství změkčovací soli je malé nebo je dávkování nastaveno na špatnou tvrdost vody (viz Leštící prostředky a změkčovací sůl). • Kryt dávkovače soli není správně uzavřen. • Došel leštící prostředek nebo je ho použito malé množství. • Nádobí je vyrobeno z nepřilnavého materiálů. • Je nastaveno příliš leštícího prostředku.
Nádobí a skleničky jsou žíhané nebo mají modravý nádech.
• Došel leštící prostředek nebo je dávkování příliš malé (viz Leštící prostředky a změkčovací sůl).
Nádobí nebylo řádně vysušeno.
• Dávkovač leštícího prostředku je nastaven na malou hodnotu. • Byl zvolen mycí cyklus bez sušení. • Koše jsou přeplněné (viz Naplnění košíků).
Nádobí není čisté.
• • • •
Alarm při uzavření kohoutku. (uslyšíte několik krátkých pípnutí)
• Pusťte vodu a přístroj se po pár minutách zapne.
(blikají indikátory “20 min.” a “10 min.”)
Mycí cyklus ještě neskončil. Odpadní hadice je ohnutá (viz Instalace). Odtokový kanál je ucpaný. Filtr je zanesen zbytky jídla...
Nádobí nebylo dobře rozmístěné. Ostřikovací rameno se nemohlo volně pohybovat. Mycí cyklus je příliš slabý (viz Mycí cykly). Nebylo naměřeno správné množství mycího prostředku nebo není mycí prostředek vhodný pro tento druh mycího programu (viz Spuštění a použití). • Filtr je špinavý či zanesený (viz Péče a údržba). • Dávka změkčovací soli je nízká (viz Leštící prostředky….).
• Aktivoval se zámek přístroje, jelikož se nic neudělalo po zapípání přístroje. Vypněte přístroj pomocí tlačítka ON/OFF, zapněte přívod vody a znovu přístroj spusťte po 20 sekundách. Přeprogramujte přístroj a spusťte mycí cyklus.
Alarm ucpaného filtru. (blikají indikátory “Wash cycle in progress” a “ 10 min.”)
• Vypněte přístroj pomocí tlačítka ON/OFF a vyčistěte filtr (viz Údržba), pak přístroj opět zapněte pomocí stejného tlačítka. Přeprogramujte přístroj a spusťte mycí cyklus.
Signál poruchy solenoidového ventilu přívodu vody (bliká indikátor “20 min.”)
• Vypněte přístroj pomocí tlačítka ON/OFF a po minutě jej opět zapněte. Pokud alarm přetrvává, vypněte přívod vody, abyste zamezili vytopení, vytáhněte vidlici síťového přívodu ze zásuvky a volejte odbornou pomoc.
13
Poznámky
14
Poznámky
15
Seznam servisních středisek je uveden na internetových stránkách: http://www.indesit.cz http://www.aristonchannel.cz
Servisní modrá linka: 810 800 023
Indesit Company Česká s.r.o. U nákladového nádraží 2, 130 00 Praha 3, Česká republika
www.indeitcompany.com
Indesit Company SpA
09/2005 - 195050771.01
GB
Via Aristide Merloni, 47 - 60044 Fabriano tel. (0732) 6611 - Italy
16