Configuratie PL printers Dealer instructie v0.99
20090427_DLR POS-Line_kenniscentrum_PLP_configuratie.doc
Standaard hebben de PL-printers een IP adres (192.168.1.251) wat waarschijnlijk niet overeenkomt met dat van de QT (192.168.0.x) of van het bestaande netwerk. Om die reden zal het IP adres aangepast moeten worden. Om het huidige IP adres te wijzigen moet dit bekend zijn, het wordt weergegeven op de test-print. Volg de volgende handeling op deze uit te printen: printer uit |
indrukken | printer aan | los laten Na een print met de huidige hardware parameters worden de interface settings geprint, met daarop het huidige IP adres. (zie 1)
Nu dit bekend is kan het aangepast worden. Als er achter DHCP (zie 2) Enabled staat in plaats van Disabled kan de printer aangesloten worden op een netwerk waar DHCP aanstaat en zal dan automatisch een IP adres toegewezen krijgen. Staat DHCP op Disabled zoals in dit voorbeeld moet de PC, indien deze een andere IP range heeft, zo geconfigureerd worden dat deze in dezelfde range komt als de printer. De volgende stappen laten zien hoe dit te doen. 1.1
Wijzigen IP adres in Windows XP
Open eerst het scherm: netwerkverbindingen van Windows start | configuratiescherm | netwerkverbindingen
Toelichting of titel
-2-
20090427_DLR POS-Line_kenniscentrum_PLP_configuratie.doc
Selecteer de LAN verbinding en vervolgens de eigenschappen van het TCP/IP protocol rechtermuisknop LAN verbinding | eigenschappen | Internet Protocol (TCP/IP) | Eigenschappen
Selecteer nu de optie: “Het volgende IP-adres gebruiken“. De drie vakken daaronder en: “De volgende DNS-serveradressen gebruiken” worden actief. Vul achter IP-adres een willekeurig adres in zich wat in dezelfde range bevindt als de PL printer, bijvoorbeeld: IP-adres: Subnetmasker: Standaard-gateway:
192.168.1.1 255.255.255.0 192.168.1.1
De DNS-server adressen kunnen in dit geval leeg blijven. Klik na het invullen van de IPadressen op OK.
Toelichting of titel
-3-
20090427_DLR POS-Line_kenniscentrum_PLP_configuratie.doc
1.2
Wijzig IP adres PL-printer via ByNetWinconfig tool
Verbind de printer via een straight-cable en switch met de PC, of via een cross-cable direct met PC. Start de ByNet Winconfig software door op het pictogram te klikken
Het hoofdscherm van de software wordt geopend. Zoek nu naar aangesloten printers door op de knop: Search Printer te klikken (zie 1). Als het goed is wordt er een printer gevonden, selecteer de gevonden printer en klik op de knop IP Adress Setting (zie 2).
Een nieuw scherm verschijnt met daarin de huidige IP instellingen. Deze kunnen nu gewijzigd worden in de range van de QT, of van het netwerk waar de printer in komt te staan.
Klik na het wijzigen op OK, de melding verschijnt dat de instellingen gewijzigd zijn. De printer kan nu met de QT-6600 of netwerk verbonden worden.
Toelichting of titel
-4-
20090427_DLR POS-Line_kenniscentrum_PLP_configuratie.doc
1.3
Wijzigen IP-adres PL-printer via webinterface
Verbind de printer via een straight-cable en switch met de PC, of via een cross-cable direct met PC. Open de standaard internetbrowser en geeft in de adresbalk het huidige, zojuist gevonden, IP-adres van de PL-printer in (zie 1), een configuratiepagina zal nu verschijnen.
Klik op de link; Configure Interface, een nieuwe pagina wordt geopend.
Wijzig het IP-adres, Subnet Mask en Gateway Address (1) naar de juiste waarde in de range van de QT of het doelnetwerk. Klik vervolgens op Save (2). De printer kan nu met de QT-6600 of netwerk verbonden worden.
Toelichting of titel
-5-
20090427_DLR POS-Line_kenniscentrum_PLP_configuratie.doc
2. Configuratie QT-6600 De ethernetprinters wordt niet automatisch herkend door de QT-6600 en moeten daarom handmatig toegevoegd worden.
1. Geheugen indeling | 6. Per bestand | 900 Reserveer voldoende geheugen voor gebruik van ethernet printers, deze waarde moet minimaal 11 zijn.
1. Smart Specialiteiten | 30. TCP/IP | 0011-900 | <selecteer laatste kolom > | IPadres ethernetprinter | JA Regels 0011-900 tot en met 0026-900 worden gebruikt voor de definitie van de ethernetprinters. 0011-900 betreft het de eerste ethernetprinter.
1. Smart Specialiteiten | 13. Printertabel | BON | <selecteer tweede kolom > | 5. LAN Printer | 1. MC #01 | 1. Lan Printer 1. | JA Stel hier eventueel een back-up printer in en herhaal deze handeling voor de Rapportage printer. De ethernetprinter is nu klaar voor gebruik
G:\CC POS\POS-Line_Intern\POS-Line_Correspondentie\POS-Line Standaard Documenten\POS-Line_kenniscentrum_Document.doc
Toelichting of titel
-6-