ORT-01
Electronic modulating room thermostat for OpenTherm appliances Installation and User Guide Danfoss Heating
Index
Index GB Specification..................................................................................... 3-4 Positioning and installation .............................................................5 Wiring................................................................................................ 6-7 Mounting..............................................................................................8 Locking & Limiting..................................................................................9 User Instructions............................................................................. 10-11
NL Technische Specificaties.............................................................12-13 Positionering / Installatie................................................................ 14 Bedrading.....................................................................................15-16 Montage............................................................................................. 17 Blokkeren & Begrenzen...................................................................... 18 Gebruikers handleiding............................................................... 19-20
2
Specification Code Number Temperature range
087N774300 8-30°C
Maximum ambient temperature
45°C
Control type
P+I
OpenTherm software version
2.3
Domestic hot water keep hot feature
•
Holiday mode
•
ID 14 low load control Thermostat output Construction IP rating Supply voltage Wiring, non-polarised 2 wire bus Control pollution situation
Specification
GB NL
Specification
• Data EN60730-2-9 IP20 24V DC from boiler • Degree 2
Ball hardness test
75°C
Dimensions (mm)
86 high x 85 wide x 42 deep
3
Specification
GB NL Specification ERP Class The products represented within this document are classified according to, and allow completion of, the Energy Related Product (ErP) Directive System Package fiche and the ErP system data label. ErP Labelling obligation is applicable from 26th September 2015. ErP Class
V
ErP Class 5 Product
4
Product Function and ErP Description Modulating Room Thermostat, for use with modulating heaters An electronic room thermostat that varies the flow temperature of the water leaving the heater dependent upon measured room temperature deviation from room thermostat set point. Control is achieved by modulating the output of the heater.
Additional efficiency gain
3%
(5FT)
ORT-01
GB NL Positioning and Installation
Positioning and Installation
5
Wiring
GB NL Wiring
6
1.
For surface mounted wiring, cutouts are provided on the backplate to enable correct positioning of the cable.
2.
For recessed wiring, cabling can be connected as in diagram 2.
ORT-01
A
B
OpenTherm connections in ORT- 01
Wiring
GB NL
Wires can be crossed
O
O
OpenTherm connections in boiler
Important - To avoid damage to Boiler and Thermostat, connect only to OpenTherm connections on boiler, do not connect to any other power source.
7
Mounting
GB NL Mounting
8
Locking and Limiting
Important Note: If Holiday Function
1.
is required DO NOT adjust lower limit.
Locking and Limiting
GB NL
1. Before removing dial, turn until setting 10 aligns with reference mark on front case. 2. Remove dial, lock or limit as required (see note below). 3. Replace dial, ensuring setting 10 aligns with reference mark on case.
2.
9
User Instructions
GB NL User Instructions Unlike normal room thermostats, the ORT-01 Setting Dial varies the heat output of the Opentherm condensing boiler to which it is connected. This adds significantly to the boiler efficiency by ensuring that the Indicator boiler keeps in economical condensing mode whenever possible. Daily use is as easy as setting the thermostat dial to the required setting, the advanced electronics and software within the thermostat establish two-way communication with the Opentherm boiler to ensure optimal operation.
10
In addition to the room temperature control, the ORT-01 also incorporates a feature which, dependant on boiler type, allows the domestic hot water store in the boiler to be kept hot or to be turned off, for example when on holiday. To select hot water off, simply turn the thermostat knob to the holiday position .
Settings
GB NL
Room Temperature Setting 10 – 30°C: Set dial to required room temperature, domestic hot water store in boiler is kept hot*.
User Instructions
Holiday Setting : Controls room temperature at 8°C, (frost setting), domestic hot water store in boiler is turned off. *(This feature is dependant upon boiler type).
Indication Start-Up: When boiler is first turned on the LED will flash for 20 seconds. Normal Operation: LED will be lit whenever the boiler is firing. Holiday Mode: When thermostat is put into, or taken out of holiday setting the LED will flash for 20 seconds. larm Mode: Should a fault occur with the boiler the LED will flash A continuously to warn of failure.
11
Technische Specificaties
NL Technische Specificaties Technische Specificaties Bestelnummer Temperatuurbereik
8 - 30°C
Maximale omgevingstemperatuur
45°C
Regelprincipe
P+I
OpenTherm Protocol
2.3
Warm tapwater Comfort-functie
•
Warm tapwater Eco-functie (vakantie stand)
•
ID 14 regeling lage belasting Thermostaat output Fabrikagenorm Dichtheidsklasse Voedingsspanning Aansluiting: 2 draads, polariteit ongevoelig
12
087N774300
• OpenTherm Data EN60730-2-9 IP20 24V dc van ketel •
Emissiewaarde
Niveau 2
Afmetingen in mm (bxhxd)
85x86x42
Technische Specificaties De in dit document beschreven producten zijn geclassificeerd overeenkomstig de richtlijn voor energiegerelateerde producten (ErP) en stellen u in staat om zowel het datablad voor het systeempakket als het ErP-systeemlabel aan te maken. De ErP-labelverplichting gaat in op 26 september 2015. ErP-klasse
V
ErP Class 5 Product
Productfunctie en ErP-beschrijving Modulerende kamerthermostaat, voor gebruik met modulerende verwarmingen Een elektronische kamerthermostaat die de stromingstemperatuur van het water vanuit de verwarming varieert op basis van de gemeten afwijking van de kamertemperatuur ten opzichte van het setpoint van de kamerthermostaat. De regeling vindt plaats door het uitgangsvermogen van de verwarming te moduleren.
Extra rendement
Technische Specificaties
NL
ErP-klasse
3%
13
Positionering / Installatie
NL Positionering / Installatie
14
(5FT)
ORT-01
Bedrading For surface mounted wiring, cutouts are provided on the backplate to enable correct positioning of the cable.
2.
For recessed wiring, cabling can be connected as in diagram 2.
Bedrading
NL
1.
15
Bedrading
NL Bedrading
A
B
OpenTherm OpenTherm connections aansluiting in in ORT- 01 ORT-01
Wires can be
Draden crossed mogen gewisseld worden
O
16
O
OpenTherm OpenTherm connections in aansluiting in boiler ketel
Belangrijk - Om schade aan ketel en thermostaat te voorkomen dient de thermostaat alleen op de OpenTherm aansluiting van de ketel te worden aangesloten.
NL Montage
Montage
17
Blokkeren & Begrenzen
NL Blokkeren & Begrenzen 1. Draai de instelknop op stand 10. 2. Verwijder de instelknop en blokkeer of begrens naar behoefte ( zie onderstaand schema). 3. Plaats de instelknop op stand 10 weer terug. Let op: Stel geen minimum begrenzing in als de Vakantie Stand nodig is.
1.
18
2.
Gebruikers handleiding
NL
Anders dan bij normale aan/uit thermostaten regelt de ORTInstelknop 01 de warmteafgifte van de OpenTherm ketel waarop hij is aangesloten. Dit draagt in hoge mate bij aan het ketelrendement door te zorgen dat de ketel zo lang LED Indicator mogelijk in HR (condenserend) bedrijf werkt. Dagelijks gebruik is zeer eenvoudig door de instelknop van de thermostaat simpelweg op de gewenste temperatuur in te stellen. De geavanceerde elektronika en innovatieve software in de thermostaat verzorgen de twee-weg-communicatie met de OpenTherm ketel en verzekeren een optimale werking. Naast de nauwkeurige ruimtetemperatuurregeling voorziet de ORT-01 ook in de funktie, afhankelijk van het type ketel, om de warme tapwatervoorraad op temperatuur te houden (comfort) of uit te schakelen (eco), bijvoorbeeld tijdens vakanties buitenshuis. Om de eco-funktie te aktiveren dient de instelknop op de vakantiestand te worden gezet.
Gebruikers handleiding 19
NL
Instellingen
Instellingen
Ruimtetemperatuur instelling 10 – 30°C: Zet de instelknop op de gewenste ruimtetemperatuur, tapwater voorraad wordt op temperatuur gehouden*. Vakantiestand : Regelt de ruimtetemperatuur op 8°C, (vorst beveiliging), warm tapwater uitgeschakeld*. *(Deze funktie is afhankelijk van het keteltype). LED-indicator Opstarten: Na het inschakelen van de voedingsspanning van de ketel knippert de LED gedurende 20 seconden. Normaal bedrijf: LED is aan wanneer de ketel brandt. Vakantiestand: Wanneer de thermostaat op Vakantiestand wordt gezet knippert de LED twee keer, bij terugzetten op normaal bedrijf een keer.
20
Alarm funktie: Indien zich een fout in de ketel voordoet, zal de LED als waarschuwing continu knipperen.
21
22
23
www.heating.danfoss.co.uk
24
Part No 25219 Issue 4 06/2015 (VIRLA14L)