ADRESA PŘEVODNÍ TABULKA pro ruční nastavení ADDRESS CONVERSION TABLE FOR MANUAL SETTING Adresa Okruh chladiva
Refrigerant circuit address
V případě hromadné chladicího systému, by měl být nastaven každý systém chladiva exkluzivní In the case of a multiple refrigerant system, each refrigerant system should be set an adresa okruh chladiva. exclusive refrigerant circuit address. Conversion table ofchladiva refrigerant circuit addressnastavení and rotary switch jsou setting are shown Převodní tabulka adresy obvodu a otočného přepínače zobrazeny v níže uvedené tabulce. in the table below. Do not use a nonexistent switch setting combination. Rotary SW setting is formed with the Hexadecimal notation.
Nepoužívejte neexistující kombinaci nastavení přepínače. Rotační nastavení SW je tvořen s šestnáctkové soustavě
Refrigerant circuit address conversion table (Outdoor unit) (SW9 : "0" , SW8 : "0" - - - Factory setting)
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1
0 1 2 3 4 5 6 7 8 9 A B C D E F 0 1 2 3
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39
1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2
4 5 6 7 8 9 A B C D E F 0 1 2 3 4 5 6 7
40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59
2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3
8 9 A B C D E F 0 1 2 3 4 5 6 7 8 9 A B
60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79
3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
Example : Refrigerant circuit address 30 : Set Rotary SW9 to "1" and SW8 to "E" B C DE A
B C DE
3 456
3 456
A
2
789
SW9
F0 1
2
F0 1
SW8
- (06 - 57) -
C D E F 0 1 2 3 4 5 6 7 8 9 A B C D E F
80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99
5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 6 6 6 6
0 1 2 3 4 5 6 7 8 9 A B C D E F 0 1 2 3
SYSTEM DESIGN
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
789
SYSTEM DESIGN
Chladiva Rotary Switch Refrigerant Refrigerant Rotary Switch Refrigerant Rotary Switch Refrigerant Rotary Switch Refrigerant Rotary Switch obvod setting setting setting setting setting circuit circuit circuit circuit circuit adresa address address address address address SW9 SW8 SW9 SW8 SW9 SW8 SW9 SW8 SW9 SW8
Okruh chladiva adresa konverzní tabulky (Vnitřní jednotka) Refrigerant circuit address conversion table (Indoor unit) Kazeta 1 PCB Type A : Compact Cassette Type CassetteTyp Type
Duct Type TypeFloor / Ceiling Kanálové StropníType Type
Low Static Pressure Duct Type Ceiling Type
Compact Duct Type
Wall Mounted Type
Ceiling Wall Type (SW9 : "0" , SW8 : "0" - - - Factory setting)
Refrigerant Rotary Switch Refrigerant Rotary Switch Refrigerant Rotary Switch Refrigerant Rotary Switch Refrigerant Rotary Switch setting setting setting setting setting circuit circuit circuit circuit circuit address address address address address 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1
SW9 SW8
0 1 2 3 4 5 6 7 8 9 A B C D E F 0 1 2 3
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39
1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2
4 5 6 7 8 9 A B C D E F 0 1 2 3 4 5 6 7
SW9 SW8 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59
2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3
8 9 A B C D E F 0 1 2 3 4 5 6 7 8 9 A B
SW9 SW8 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79
3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
Example : Refrigerant circuit address 30 : Set Rotary SW9 to "1" and SW8 to "E" B C DE
B C DE A
789
A
3 456
3 456
789
SW9
F0 1
2
F0 1
SW8
- (06 - 58) -
C D E F 0 1 2 3 4 5 6 7 8 9 A B C D E F
SW9 SW8 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99
5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 6 6 6 6
0 1 2 3 4 5 6 7 8 9 A B C D E F 0 1 2 3
SYSTEM DESIGN
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
2
SYSTEM DESIGN
SW9 SW8
Refrigerant circuit address conversion table (Indoor unit) Okruh chladiva adresa konverzní tabulky (Vnitřní jednotka) 2 PCB Type B : Compact Wall Mounted Type (Comfort model) AS*E07, AS*E09, AS*E12, AS*E14
5-1
5-2
5-3
0
OFF
OFF
OFF
0
1
OFF
OFF
OFF
1
2
OFF
OFF
OFF
3
OFF
OFF
4
OFF
OFF
5
OFF
6
OFF
7
DIP-SW
Rotary Refrigerant SW SW7 circuit address
DIP-SW
Rotary Refrigerant SW SW7 circuit address
5-1
5-2
5-3
25
ON
OFF
OFF
9
26
ON
OFF
OFF
A
2
27
ON
OFF
OFF
OFF
3
28
ON
OFF
OFF
4
29
ON
OFF
OFF
OFF
5
30
ON
OFF
OFF
6
31
ON
OFF
OFF
OFF
7
32
8
OFF
OFF
OFF
8
9
OFF
OFF
OFF
9
10
OFF
OFF
OFF
11
OFF
OFF
12
OFF
OFF
13
OFF
14 15
DIP-SW
Rotary Refrigerant SW SW7 circuit address
5-1
5-2
5-3
50
ON
ON
OFF
2
51
ON
ON
OFF
3
B
52
ON
ON
OFF
OFF
C
53
ON
ON
OFF
D
54
ON
ON
OFF
OFF
E
55
ON
OFF
OFF
F
56
ON
OFF
ON
OFF
0
57
33
OFF
ON
OFF
1
34
OFF
ON
OFF
2
A
35
OFF
ON
OFF
OFF
B
36
OFF
ON
OFF
C
37
OFF
ON
OFF
OFF
D
38
OFF
OFF
OFF
OFF
E
39
OFF
OFF
OFF
F
40
16
ON
OFF
OFF
0
17
ON
OFF
OFF
18
ON
OFF
OFF
19
ON
OFF
20
ON
21
ON
22
DIP-SW
Rotary SW SW7
5-1
5-2
5-3
75
OFF
OFF
ON
B
76
OFF
OFF
ON
C
4
77
OFF
OFF
ON
D
OFF
5
78
OFF
OFF
ON
E
OFF
6
79
OFF
OFF
ON
F
ON
OFF
7
80
ON
OFF
ON
0
ON
OFF
8
81
ON
OFF
ON
1
ON
ON
OFF
9
82
ON
OFF
ON
2
58
ON
ON
OFF
A
83
ON
OFF
ON
3
59
ON
ON
OFF
B
84
ON
OFF
ON
4
3
60
ON
ON
OFF
C
85
ON
OFF
ON
5
OFF
4
61
ON
ON
OFF
D
86
ON
OFF
ON
6
OFF
5
62
ON
ON
OFF
E
87
ON
OFF
ON
7
ON
OFF
6
63
ON
ON
OFF
F
88
ON
OFF
ON
8
OFF
ON
OFF
7
64
OFF
OFF
ON
0
89
ON
OFF
ON
9
OFF
ON
OFF
8
65
OFF
OFF
ON
1
90
ON
OFF
ON
A
41
OFF
ON
OFF
9
66
OFF
OFF
ON
2
91
ON
OFF
ON
B
1
42
OFF
ON
OFF
A
67
OFF
OFF
ON
3
92
ON
OFF
ON
C
2
43
OFF
ON
OFF
B
68
OFF
OFF
ON
4
93
ON
OFF
ON
D
OFF
3
44
OFF
ON
OFF
C
69
OFF
OFF
ON
5
94
ON
OFF
ON
E
OFF
OFF
4
45
OFF
ON
OFF
D
70
OFF
OFF
ON
6
95
ON
OFF
ON
F
OFF
OFF
5
46
OFF
ON
OFF
E
71
OFF
OFF
ON
7
96
OFF
ON
ON
0
ON
OFF
OFF
6
47
OFF
ON
OFF
F
72
OFF
OFF
ON
8
97
OFF
ON
ON
1
23
ON
OFF
OFF
7
48
ON
ON
OFF
0
73
OFF
OFF
ON
9
98
OFF
ON
ON
2
24
ON
OFF
OFF
8
49
ON
ON
OFF
1
74
OFF
OFF
ON
A
99
OFF
ON
ON
3
Example : Refrigerant circuit address 30 : Set DIP-SW5-1 to "ON" ,5-2 and 5-3 to "OFF", Rotary SW7 to "E" B C DE
F0 1
1
2
3
4
DIP-SW5
3 456
A
2
ON
SW7
- (06 - 59) -
SYSTEM DESIGN
Refrigerant circuit address
789
SYSTEM DESIGN
(SW5-1: "OFF" , SW5-2: "OFF", SW5-3: "OFF" ,SW7: "0" --- Factory setting)
Vnitřní adresa jednotky Indoor unit address Každá vnitřní jednotka chladicího systému, by mělabe býtset nastavena exkluzivní vnitřní Each indoor unit in avrefrigerant system should an exclusive indoor unitjednotku projednat s otočnými přepínači nebo přepínače DIP. address with rotary switches or DIP switches.
Conversion table of indoor address and rotary switch settingjsou are zobrazeny shown v níže uvedené tabulce. Převodní tabulka vnitřní adresyunit jednotky a rotační nastavení přepínače in the table below. Nepoužívejte neexistující kombinaci nastavení přepínače. Rotační SW je tvořen s hexadecimálním tvaru Do not nastavení use a nonexistent switch setting combination. Rotary SW setting is formed with the Hexadecimal notation Vnitřní jednotka konverzní tabulky adres Indoor unit address conversion table
1 PCB Type A :
Compact Cassette Type
Cassette Type
Low Static Pressure Duct Type Ceiling Type
Compact Duct Type
Duct Type
Wall Mounted Type
Floor / Ceiling Type
Ceiling Wall Type (SW7 : "0" , SW6 : "0" - - - Factory setting)
Rotary Switch Rotary Switch Rotary Switch Rotary Switch Rotary Switch Indoor unit Indoor unit Indoor unit Indoor unit setting setting setting setting setting address
0 1 2 3 4 5 6 7 8 9 10 11 12
0 0 0 0 0 0 0 0 0 0 0 0 0
SW7 SW6
0 1 2 3 4 5 6 7 8 9 A B C
13 14 15 16 17 18 19 20 21 22 23 24 25
0 0 0 1 1 1 1 1 1 1 1 1 1
D E F 0 1 2 3 4 5 6 7 8 9
address
SW7 SW6 26 27 28 29 30 31 32 33 34 35 36 37 38
1 1 1 1 1 1 2 2 2 2 2 2 2
A B C D E F 0 1 2 3 4 5 6
B C DE A
B C DE
3 456
3 456
A
2
789
SW7
F0 1
2
F0 1
SW6
- (06 - 60) -
address
SW7 SW6 39 40 41 42 43 44 45 46 47 48 49 50 51
Example : Indoor unit address 47 : Set Rotary SW7 to "2" and SW6 to "F"
789
SYSTEM DESIGN
SW7 SW6
address
2 2 2 2 2 2 2 2 2 3 3 3 3
7 8 9 A B C D E F 0 1 2 3
SW7 SW6 52 53 54 55 56 57 58 59 60 61 62 63
3 3 3 3 3 3 3 3 3 3 3 3
4 5 6 7 8 9 A B C D E F
SYSTEM DESIGN
Indoor unit address
Vnitřní jednotka konverzní tabulky table adres Indoor unit address conversion 2 PCB Type B : Compact Wall Mounted Type (Comfort model) AS*E07, AS*E09, AS*E12, AS*E14 (SW4-1: "OFF" , SW4-2: "OFF", SW6: "0" --- Factory setting) Indoor unit address
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
DIP-SW 4-1
4-2
OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
Rotary SW SW6
Indoor unit address
0 1 2 3 4 5 6 7 8 9 A B C D E F
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
DIP-SW 4-1
4-2
ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON
OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
Rotary SW SW6
Indoor unit address
0 1 2 3 4 5 6 7 8 9 A B C D E F
32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47
DIP-SW 4-1
4-2
OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON
Rotary SW SW6
Indoor unit address
0 1 2 3 4 5 6 7 8 9 A B C D E F
48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63
DIP-SW 4-1
4-2
ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON
ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON
Rotary SW SW6
0 1 2 3 4 5 6 7 8 9 A B C D E F
Example : Indoor unit address 47 : Set DIP-SW4-1 to "OFF" ,4-2 to "ON", Rotary SW6 to "F" B C DE
F0 1
3
4
SW6
SYSTEM DESIGN
DIP-SW4
SYSTEM DESIGN
2
789
1
3 456
A
2
ON
- (06 - 61) -
ADRESY 6-5-4. INFRARED NASTAVENÍ ADDRESS SETTING Bezdrátový dálkový ovladač (UTB(UTB- VB), nastavit nastavení A wireless remote controller VB) je is nutné required to set infračerveného the infrared address setting. Tato je kisdispozici vein všech vnitřníunit jednotky infračerveným přijímačem signálu. This funkce function available all indoor with sinfrared signal receiver.
Infrared address setting for duct type models can be made possible by using the
Infračervené nastavení adresy pro modely typu potrubí může být umožněno pomocí volitelná jednotka přijímač IR optional IR receiver unit (UTB- WA). (UTBWA). Poznámka: Vzhledem generovat vnitřníunit PCBPCB jednotka instalovaná daleko Note : Since Beepingk tomu, soundpípání generate from zindoor installed far away (not(nikoli from z IR přijímač jednotka), nemusí být slyšet zvuk. IR Receiver unit), sound might not be heard.
The indoor unit’s refrigerant circuit address and adresa indoor jednotku unit address can bepomocí set using the Adresa chladící okruh vnitřní UNITA €™ s, a vnitřní lze nastavit infračervený nastavení infrared address setting. adresy. Whenjeremote controller address setting is required, setotočným by the rotary switchna onvnitřní the indoor Když třeba dálkové ovládání nastavení adresy, nastavuje přepínačem UNITAunit’s € ™ sPCB. PCB.
PŘÍPRAVA pro FOR infračervené nastavení adresy PREPARATION INFRARED ADDRESS SETTING (1) Nastavte nathe vnitřní UNITA € ™PCB s PCB, který používá pro ručníaddress adresu (1) Set the přepínač switch on indoor unit’s that is se used for manual Nastavení je nastaveno â € œ00â € na tovární nastavení. setting is set to “00” atna factory setting. (This process unnecessary for nově newlyinstalované installed and anot yet set the SW.) (Tento postupis není nutné pro dosud nastavit SW.)
B C DE
2
3
4
F0 1
A
setting "00"
SYSTEM DESIGN
A
B C DE
A
789
setting "00" Check the position "0" (Factory setting) SYSTEM DESIGN
1
3 456
SW2
3 456
SW1
F0 1
2
SW6 SW7
JM2 JM1
789
SW9
SW8 SW3 SW4 SW5
SW4 SW5
ON
2
CN23 CN24
789
SW10
CN27
3 456
CN22 CN21
CN10
CN11
2
B C DE
SW1 SW2 SW3
F0 1
Pokud jetonastavena jiná čísla,that bude aktivován, If it is set any other numbers, setting value willže benastavená enabled. hodnota
(2) do to vnitřní jednotky. (2) Zapněte Turn onnapájení the power the indoor unit. Tím, napájení vnitřní jednotky inicializuje takže ujistěte se, že potrubí By zapnutí turning on the power indoor units initializes EEV,EEV, so make sure the piping vzduchotěsná test a vysávání byly provedeny před zapnutím napájení. air-tight test and vacuuming have been conducted before turning on the power. Také zkontrolujte znovu ujistěte se, že zapojení chyby byly před zapnutím napájení
Also check again to make sure no wiring mistakes were made before turning on the power.
Breaker ON 20A
Indoor units
- (06 - 62) -
Indoor unit
SWITCHING OF ADDRESS SETTING MODE PŘEPÍNÁNÍ SELECTION VÝBĚR nastavení adresy REŽIMU podržte (3) Stiskněte Press anda hold the “MANUAL/AUTO” button for 3 seconds. Pi Pi Pi
a hold podržte (4) Stiskněte Press and the “FAN CONTROL ” and the “+” buttons. Whilst holding Zatímco držení these těchto22buttons, tlačítek "ACL". stiskněte press thetlačítko "ACL" button.
OPERATION indicator (Red)
LAMP FAN CONTROL SET TEMP (+)
MANUAL AUTO
ACL
IR RECEIVER UNIT
Nastavení Addressadresy setting režim zobrazení mode display
MANUAL AUTO
Pozice tlačítka of € œMANUAL / AUTOâ € â se liší v varies závislosti na modelu.on the model. The position the “MANUAL/AUTO” button depending Viz návod k obsluze na pozici, která je součástí jednotky.
Refer to the operation manual for the position that is included with the unit. The error will be spojitě displayed by continuosly pressing/ AUTO" the "MANUAL/AUTO" fora 10 sec or more. Chyba se zobrazí stisknutím tlačítka "MANUAL po dobu 10 sekund více. In this case release the button or turn off the power. V takovém případě uvolněte tlačítko nebo vypněte napájení. Když adresa již byla nastavena v desce, činnosti se rozsvítí Whensethe address has already been setindikátor in the circuit board, the operation LAMP will light up a časovač a SWING lampy se zobrazí počet nastavení adresy.
up and the TIMER and SWING LAMPs will display the number of setting address.
An explanation of the displayed information asníže. shown below. Vysvětlení zobrazených informací, jak je uvedeno Jako typuWall stěny, LAMP barva se může As a strop Ceiling type, LAMP color mightlišit. be different.
Stiskněte tlačítko"VERTICAL AIRFLOW " "button (5) Stiskněte Press the “VERTICAL AIRFLOW Press the “+” or “-” buttons to select the custom (6)(6) kód, který odpovídá nastavení pomocí vnitřní poslat kód to send thevnitřní codejednotky to the indoor unit. code that matches the setting with the indoor unit. jednotky. Výběrem vhodného vlastního kódu the je By selecting the appropriate custom code, Correct code: Správný kód: možné nastavit komunikaci mezi vnitřní jednotkou communication between the indoor unit and the a Pi Pi bezdrátové wireless RCRC. become possible. CUSTOM CODE ( - - - ) A
Počáteční nastavení je " " The initial setting is
- (06 - 63) -
Chybný kód: Wrong code: Žádná odpověď No Response
SYSTEM DESIGN
SYSTEM DESIGN
SELECTION AND CONFIRMATION VÝBĚR a potvrzení vlastní kód OF CUSTOM CODE
Tlačítka Jména a funkce BUTTON NAME AND FUNCTION Refer to “6-5-2" for an outline of the address setting. Nezáleží na tom, zdawhether je adresathe chladiva obvodcircuit nebo vnitřní adresa jednotka je nastavena It does not matter refrigerant address or indoor unit address isjako setprvní. first. Metoda, kteroushown zde zobrazeny adresuunit vnitřní jednotky jako první.) (The method here setsnastaví the indoor address first.) Během nastavení vnitřní jednotka odmítnout Jakákoli operace from z dálkového During režimu address setting adresy, mode, indoor unit reject the anypříkaz operation command remoteovladače controller.
Address data
SLEEP button
Adresa nastavení Addressčíslo setting number Indoor unit address valid range ** Vnitřní adresa jednotky platný00-63 rozsah 00-63
Confirmation of addressadresy setting. Potvrzení nastavení
Refrigerant circutadresa addressplatný valid range 00-99 Chladící okruh rozsah 00-99
Address code
MASTER CONTROL button
01 --- Vnitřní Indoor unit address adresa jednotka Adresa Chladicího okruhu 02 --- Refrigerant circuit address
Spusťte nastavení - Start therežim address setting adresy mode Změní zobrazení adresy číslice - Changes the address display digits
FAN MODE button Switches between address (top Přepíná mezi údaji the adres (hornídata řádek) a line) and address code (bottom adresa kód (spodní řádek) line)
START/STOP button
"+" and "-" button Increases and decreases thečíslo displayed number Zvyšuje a snižuje zobrazené
IR RECEIVER UNIT
SYSTEM DESIGN
SYSTEM DESIGN
Přenáší nastavení Transmits address adresy setting
OPERATION LAMP Indication of address code
TIMER LAMP Indication of address data number (1 degit)
SWING LAMP Indication of address data number (10 degit) * IR Reciver unit is not shown for swing mark
MANUAL/AUTO button Long push ----- Switches between the address setting mode and (3 sec more) the address setting complete mode. Short push ----- Switches the indicator display (between the indoor unit address and refrigerant circuit address)
MANUAL AUTO
Note : Address code display is as follows (operation lamp display) OPERATION LAMP
INDOOR UNIT ADDRESS DISPLAY
ON
ON
ADDRESS SETTING MODE
OFF
ADDRESS SETTING COMPLETE MODE
OFF
REFRIGERANT CIRCUIT ADDRESS DISPLAY
OFF (Light continuously)
(Light 3 sec ON / 1 sec OFF)
ON
ON
OFF
(Light OFF)
- (06 - 64) -
(Light 0.5 sec ON / 0.5 sec OFF)
ADDRESS SETTING INDOOR UNIT ADDRESS SETTING (7) Press the “MASTER CONTROL to access the address setting mode.
” button
(8) Make sure the bottom number address code is ‘01’. If the number is other than ‘01’, press the “+” or the “-” buttons to alter. SET "01"
(9) Press the “FAN CONTROL ” button to access the address data setting mode. The address data will flash once this button is pressed.
(10) Press the “+” or the “-” buttons to adjust the address data. The indoor unit address range is between 00 and 63. Each time the master control button is pressed, it switches between 1 unit and 10 units positions.
Address data
Change degit
Range 00 - 63
(11) Press the “START/STOP ” button once to send the information. A beeping noise will be heard if the command is accepted. Pi Pi Pi PiPiPi
(12) Indoor unit will display the indoor unit address data number on "TIMER "(GREEN) and "SWING "(ORANGE) light. OPERATION (RED)
continuously
TIMER (GREEN)
SWING (ORANGE)
Flashing times of address numbers (1 degit)
Flashing times of address numbers (10 degit)
(Example) ADDRESS : 34 OPERATION LAMP (RED) TIMER LAMP (GREEN)
In the following cases the setting signal is not read and a buzzer sounds. The indoor unit address No. is set out of range (64 or more) : Pi Pi Pi (3 sec)
SWING LAMP (ORANGE)
The setting of the rotary switch on the PCB is not "00" : Pi Pi Pi Pi Pi
(13) Press the “SLEEP” button.
PiPi WRONG: Pi
4 times
1 - 10 sec
0.5sec ON / 0.5sec OFF 3 times
1 - 10 sec
ADDRESS 0 setting will not indicate TIMER LAMP.
KONTROLA NASTAVENÍ ADRESY CHECK ADDRESS SETTING
PiPi CORRECT : Pi
0.5sec ON / 0.5sec OFF
PiPiPiPiPi (3 sec)
- (06 - 65) -
SYSTEM DESIGN
SYSTEM DESIGN
+ : UP - : DOWN
CHLADIVOVÝ OKRUH NASTAVENÍ ADRESYSETTING REFRIGERANT CIRCUIT ADDRESS Note : The refrigerant circuit address can also be set evenwhile above indoor unit address display. (14) Press the “FAN CONTROL the address code.
” button to select
(15) Press the "+" or "-" button to adjust address code 02. SET "02"
Address code
(16) Press the “FAN CONTROL ” button to access the address data setting mode. The address data will flash once this button is pressed.
(17) Press the “+” or the “-” buttons to adjust the address data. The refrigerant circuit address range is between 00 and 99. Each time the "master control " button is pressed, it switches between 1 unit and 10 units positions.
Address data
Change digit
Range 00 - 99
+ : UP - : DOWN
(19) Indoor unit will display the refrigerant circuit address data number on "TIMER "(GREEN) and "SWING "(ORANGE) light. OPERATION (RED)
Pi Pi Pi PiPiPi
3 sec ON 1 sec OFF
TIMER (GREEN)
SWING (ORANGE)
Flashing times of address numbers (1 degit)
Flashing times of address numbers (10 degit)
(Example) ADDRESS : 25 OPERATION LAMP (RED) 0.5sec ON / 0.5sec OFF
TIMER LAMP (GREEN)
In následujících the following cases the setting signal is notnení V případech nastavení signálu načten a zazní bzučák. read and a buzzer sounds.
SWING LAMP (ORANGE)
The settingotočného of the rotary switch na on PCB the PCB Nastavení přepínače není is not "00" : Pi Pi Pi Pi Pi
” button.
PiPi CORRECT : Pi PiPi WRONG: Pi
1 - 10 sec
2 times
1 - 10 sec
ADRESA 00 nastavení nebude indikovat kontrolka ADDRESS setting will not indicate TIMER LAMP samospouště a SWING LAMP. and SWING LAMP. Displej adresa budewill automaticky přepne z vnitřní ADDRESS display automatically switched from adresa jednotka chladiva adresu obvodu indoor unit address to refrigerant circuit address.
KONTROLA NASTAVENÍ ADRESY CHECK ADDRESS SETTING (20) Press the “SLEEP
5 times
0.5sec ON / 0.5sec OFF
PiPiPiPiPi (3 sec)
- (06 - 66) -
SYSTEM DESIGN
SYSTEM DESIGN
(18) Press the “START/STOP ” button to send tlačítkoonce pro odeslání Informace. Pípání hluku bude slyšet, jestliže the information. A beeping noise will be heard if the Příkaz je akceptován command is accepted.
DISPLAY CODE SWITCHING DISPLAY ADDRESS ADRESA Přepínání kódů (21) Address display switches indoor unit 21) displej Adresa přepíná mezibetween vnitřní jednotkou adresa a chladiva okruh adresa stisknutím / address and refrigerant circuit address"MANUAL by pressing AUTO Tlačítko jednou krátce ". once shortly. "MANUAL/AUTO " button
Indoor unit address OPERATION LAMP : ON OPERATION LAMP (RED) TIMER LAMP (GREEN)
Pi
0.5sec ON / 0.5sec OFF
1 - 10 sec 4 times 0.5sec ON / 0.5sec OFF
SWING LAMP (ORANGE)
3 times
1 - 10 sec
OPERATION LAMP (Red)
Refrigerant circuit address OPERATION LAMP : 3 sec ON / 1 sec OFF
MANUAL AUTO
OPERATION LAMP (RED)
IR RECEIVER UNIT MANUAL AUTO
TIMER LAMP (GREEN)
0.5sec ON / 0.5sec OFF 5 times 1 - 10 sec 0.5sec ON / 0.5sec OFF
SWING LAMP (ORANGE)
2 times
1 - 10 sec
Check to makezda surejethe address setting Zkontrolujte, nastavení adresaisjecorrect. správná
COMPLETION OF ADDRESS SETTING MODE DOSTAVBA nastavení adresy REŽIMU (22) Press and hold the “MANUAL/AUTO 3 seconds.
” button for
(23) Press the “ACL” button. Stiskněte Po stisknutí tlačítka ACL,button, After pressing the ACL nastavte prosím vlastní kód please set the custom code bude-li c, d nastavení. again ifb,b,c,d setting.
SYSTEM DESIGN
OPERATION LAMP (Red) * Operation lamp change displays MANUAL AUTO
IR RECEIVER UNIT
ACL MANUAL AUTO
Kontrolka samospouště blikánumber keep počet dob of Adresa No No. Timer lamp keep blinks the of times address
SYSTEM DESIGN
Pi Pi Pi
Nastavení adresy signál není přijat afer zapnutí adres režimu dokončení nastavení.mode. (Pi Pi Pi Pi Pi) The address setting signal is not received afer switched address setting completion Press the "MANUAL/AUTO
"opět tlačítko pofor dobu 3 sekund pro návrat do v případě potřeby do režimu nastavení " button again 3 sec to return to if required to return the vrátit address setting mode. adresy.
24) Stisknutím tlačítka o/I MANUAL / AUTO a krátce (24) Press “MANUAL/AUTO ” button shortly to select tlačítko pro výběr obatoadresa ke kontrole správného the both address be checked correct setting
Indoor unit address OPERATION LAMP : OFF
nastavení
OPERATION LAMP (RED) TIMER LAMP (GREEN)
1 - 10 sec 4 times 0.5sec ON / 0.5sec OFF
SWING LAMP (ORANGE)
OPERATION LAMP (Red)
MANUAL AUTO
0.5sec ON / 0.5sec OFF
3 times
1 - 10 sec
Refrigerant circuit address OPERATION LAMP : 0.5 sec ON / 0.5 sec OFF
IR IRRECEIVER přijímač UNIT MANUAL AUTO
OPERATION LAMP (RED) TIMER LAMP (GREEN) SWING LAMP (ORANGE)
Check to makezda surejethe address setting correct. Zkontrolujte, nastavení adresais je správná
- (06 - 67) -
0.5sec ON / 0.5sec OFF
1 - 10 sec 5 times 0.5sec ON / 0.5sec OFF 2 times
1 - 10 sec
