Vzduchové potrubní systémy www.rozvodyvzduchuairnet.cz
Rozvody vzduchu - KATALOG BILLER & BURDA s.r.o. Litvínovická 1469, 370 01Č. Budějovice tel: 387 203 682-3 • fax: 387 203 684 www.billerburda.cz
[email protected]
www.rozvodyvzduchuairnet.cz
snadno ► rychle ► spolehlivě
OBSAH OBECNÉ INFORMACE
4
TRUBKY • Trubky
8 8
TVAROVKY • Přímé spojky • Kolena • T-kusy • Odbočky • Spojky se závity • Záslepky • Rozebíratelné spojky • Koncové krabice • Redukce • Příruby
9 9 10 11 12 12 12 13 13 13
PŘÍSLUŠENSTVÍ • Kulové kohouty
14
• Klapky
14
INSTALACE • Profily, nosníky a držáky • Závěsné systémy • Náhradní díly
15 15 15
NÁŘADÍ • Kufr s nářadím AIRnet • Ostatní nářadí
16 16 16
2
OBECNÉ INFORMACE Rychlost, jednoduchost, spolehlivost Potrubní systém AIRnet je tvořen výhradně z materiálů, které nepodléhají korozi, což přináší následující výhody: • eliminace rizika znečištění • stlačený vzduch je dodáván v konstantní kvalitě od kompresoru až do místa jeho využití • zajišťuje požadovaný tlak v potrubním systému • snižuje náklady na údržbu potrubí • chrání před možnými výpadky ve výrobě
Úspory se systémem AIRnet
Kompletní řešení
Použití perfektně hladkého povrchu uvnitř částí systému AIRnet zajišťuje: • žádnou cirkulaci vzduchu • minimální tlakový spád • žádné plýtvání energií spotřebovanou na výrobu vzduchu
Potrubní systém AIRnet nabízí kompletní řešení dodávky vzduchu od kompresoru až ke koncovému odběrnému místu. Systém je tvořen hliníkovými trubkami a polymerovými spojkami o světlostech od 20 do 100 mm (3/4“ až 4“). Dále systém obsahuje celou řadu potřebného montážního příslušenství.
Vysoká kompatibilita
Vysoká odolnost materiálu
• lze napojit na jakýkoliv stávající potrubní systém • umožňuje budoucí úpravy a rozšíření potrubí • systém AIRnet je neustále vyvíjen a rozšiřován
Potrubí systém AIRnet je odolný vůči korozi, mechanickým otřesům, teplotní výkyvům a povětrnostním podmínkám.
Rychlá instalace • hliníkové trubky používané systémem AIRnet jsou velmi robustní a přitom lehké a se snadným opracováním při jejich řezání • systém může být instalován zpravidla jedním technikem a to bez speciálního zaškolení • polymerové spojky zajišťují perfektní spojení a pro spojování systému není třeba svařování, lepení nebo lisování • rozměry do průměru 25 mm (1“) lze spojit ručně a přitom s perfektní těsností • ihned po montáži lze rozvod natlakovat, což snižuje zbytečnou dobu čekání na zahájení provozu
3
Flexibilní umístění AIRnet umožňuje snadnou montáž, demontáž a díky tomu opětovné použití, rychlé možnosti rozšíření a plnou kontrolu nad rozvody.
Minimum úniků • těsnící kroužky zajišťují vzduchotěsnost • odolnost proti vibracím • bez rizika koroze • snadná údržba systému • žádné plýtvání energií
OBECNÉ INFORMACE NORMY
EN 13480 / směrnice 97/23/ES a ASME B31.1 v souladu s osvědčeními pro běžné tlaky související se schváleními PED - CE - ASME - TUV Ø 20 - 25 - 40 - 50 - 63 - 80 - 100 mm 3/4” - 1” - 1 1/2” - 2” - 2 1/2” - 3” - 4”
TECHNICKÉ ÚDAJE
• určeno pro stlačený vzduch a dusík • maximální provozní tlak PN13 pro teploty mezi -20 °C a +70 °C • provozní teplotní limity: -20 °C/+70 °C • nejnižší povolená hodnota rosného bodu: -70 °C • odolnost proti vlivu kompresorových olejů (minerální oleje, oleje na bázi PAO nebo esteru) • trubky AIRnet jsou odolné proti přímému UV záření, spojky jsou odolné proti nepřímému UV záření • odolné vůči korozi • zajišťující žádné úniky • určeno pro vzduch vyráběný jak mazanými, tak bezolejovými kompresory • úroveň podtlaku (použití pro vakuum): průměry 20-80 mm až pro hodnotu 0,13 bar absolutního tlaku
Polymerové tvarovky (20 - 50 mm)
• materiál PA6 s 15% sklolaminátovou injekcí
Hliníkové tvarovky (63 - 80 mm)
• z hliníkové slitiny EN-AB46100
Trubky
• materiál svorky: ocel S355MC, dle normy EN10149-2
• extrudovaný hliník UNS, slitina A96063 T5
• označené maximálním • Spojka: odlévaný hliník povoleným tlakem • těsnění: pryž NBR 70 Sh AISi9Mg • potisk na trubce: • těsnění: pryž NBR 70 Sh • označení na tvarovce: • svěrný kroužek: nerezová - kód výrobku ocel AISI 304 • označení na tvarovce: - jmenovitá světlost - kód výrobku • těsnění: pryž NBR 70 Sh - datum výroby - jmenovitá světlost - kód výrobku - jmenovitá světlost - datum výroby • označení na tvarovce: - datum výroby - kód výrobku • svěrný kroužek: nerezová ocel
• svěrný kroužek: nerezová ocel
Tvarovky z oceli-hliníku (100 mm)
- jmenovitá světlost - datum výroby
TESTOVÁNÍ
Potrubní systém AIRnet byl testován za podmínek nejvyšších průmyslových standardů • na odolnost vůči vysokému tlaku po dobu jedné hodiny • destrukčním testem na úroveň poruchového tlaku • testem na úniky za použití vibračních cyklů o různých frekvencích • testem na úniky při použití tlakové pulzace 4
OBECNÉ INFORMACE Konstrukce tvarovek systému AIRnet 3 1 2
5 4
1 KONSTRUKCE PRO SILNÉ DOTAŽENÍ
4 SPECIFICKÉ VEDENÍ NA VSTUPU DO TVAROVKY
Nová konstrukce zvyšující možnost dotažení, sílu a bezpečnost (za použití kroužku z nerezové oceli)
Pro snazší vložení trubky a perfektní zarovnání trubky ve spojce
2 SPECIFICKÝ TVAR DOTAHOVACÍHO KROUŽKU Zářezy na kroužku umožňují zajistit těsné spojení a to bez poškození kroužku
5 OZNAČENÍ DÍLŮ Na výrobku je vyraženo číslo tvarovky a průměr
3 SPECIFICKÝ TVAR TĚLA TVAROVKY Velmi velký vnitřní průměr těla eliminuje účinky proudění vzduchu a výrazně přispívá ke snížení tlakového spádu
AIRnet 10-letá záruka Díky vysoké kvalitě potrubního systému AIRnet poskytujeme zákazníkům 10 letou záruku na spojky a hliníkové trubky AIRnet a to na jakékoliv škody vyplývající z vad materiálu.
Podmínky pro uplatnění záruky: • Proveďte instalaci podle instrukcí a pokynů výrobce
• Záruka na systém AIRnet je omezena pouze na náhradu komponentů
• Chraňte potrubní systém AIRnet proti otřesům, vibracím a korozivnímu prostředí
• Reklamační žádosti řeší výhradně dovozce systému nebo jím pověřené servisní středisko
• Poškozené díly musí být předloženy pro kontrolu a řešení reklamace
• Tato 10 letá záruka je omezena na poskytnutí nové spojky nebo potrubí a je předmětem našeho rozhodnutí, zda se jedná o závadu způsobenou výrobní vadou
• Používejte pouze originální náhradní díly
Ukázka snadnosti spojování AIRnet používá jediný způsob montáže pro všechny průměry pro zajištění co nejkratší doby montáže, od 1,5 minuty při nejmenších až do 4 minut při největších průměrech. Krok 1 Krok 2
Krok 3
Zatlačte trubku do tvarovky Ručně utáhněte
Ukázka označení trubek
5
Zajistěte klíčem (nezbytné pouze pro tvarovky o průměru větším než 40 mm (1 1/2“)
OBECNÉ INFORMACE AIRnet vs. tradiční pozinkované trubky
Systém AIRnet
Běžné pozinkované trubky
hladký povrch
drsný povrch
nízký koeficient tření
koeficient tření je téměř dvojnásobný
nízký pokles tlaku (např. u potrubí o délce 400 m a světlosti 50 mm / 2“ je při tlaku 7 bar a průtoku 110 l/s tlakový spád pouze 0,2 bar)
vysoký pokles tlaku (např. u potrubí o délce 400 m a světlosti 50 mm / 2“ je při tlaku 7 bar a průtoku 110 l/s tlakový spád 0,37 bar)
korozivzdorné hliníkové trubky a polymerové tvarovky
ochrana proti korozi závisí na kvalitě galvanizace
žádné riziko koroze při řezání hliníku a velmi nízké úniky vzduchu skrze materiál tvarovky či trubky
při řezání trubek je porušena galvanizace; v místech, kde může být usazen kondenzát hrozí vysoké riziko úniků vzduchu
nízká hmotnost trubek (např. u průměru 50 mm váží trubka pouze 5 kg)
vysoká hmotnost trubek (např. u průměru 50 mm váží trubka více než 25 kg)
rychlé řezání hliníkových trubek
velmi dlouhá doba ručního řezání, elektrický nůž může vytvořit kovový prach
rychlé a snadné odhrotování trubek; trubky lze snadno nasunout do spojek
k montáži je zapotřebí zkušeností, aby se vytvořilo perfektně těsné spojení
spojky mohou být dotaženy ručně a zabezpečeny klíčem
pozinkované spojky je třeba dotáhnout pomocí klíče, riziko úniků závisí na kvalitě závitu
úpravy rozvodů jsou snadné: armatury a trubky mohou být jednoduše demontovány a znovu použity
úpravy rozvodů jsou často obtížné: po demontáži se musí trubky řezat, vyměnit, nasadit a znovu namontovat do okruhu
standardní modré (stlačený vzduch) nebo zelené (inertní plyny) trubky pro snadnou identifikaci potrubí
trubky je třeba dodatečně nabarvit
6
TRUBKY > Hliníkové trubky pro stlačený vzduch (5,7 m) Vnější Ø (mm)
Vnitřní Ø (mm)
Délka (mm)
Hmotnost (kg/ks)
Balení (počet tyčí)
ATB6-020T
20
17,4
5,7
1,16
10
ATB6-025T
25
22,3
5,7
1,52
10
ATB6-040T
40
36,4
5,7
3,27
5
ATB6-050T
50
46,0
5,7
4,57
4
ATB6-063T
63
58,8
5,7
6,08
3
ATB6-080T
80
74,8
5,7
9,57
2
ATB6-100T
100
94,0
5,7
13,79
1
Vnější Ø (mm)
Vnitřní Ø (mm)
Délka (mm)
Hmotnost (kg/ks)
Balení (počet tyčí)
ATG6T-020T
20
17,4
5,7
1,16
10
ATG6T-025T
25
22,3
5,7
1,52
10
Obj. č.
> Hliníkové trubky pro inertní plyny (5,7 m) Obj. č.
V průmyslových potrubních rozvodech lze pro inertní plyny jako je např. dusík použít trubky se zelenou barvou.
> Hliníkové trubky pro stlačený vzduch (2,85 m)
Vnější Ø (mm)
Vnitřní Ø (mm)
Délka (mm)
Hmotnost (kg/ks)
Balení (počet tyčí)
ATB3-020T
20
17,4
2,85
0,58
10
ATB3-025T
25
22,3
2,85
0,76
10
ATB3-040T
40
36,4
2,85
1,64
5
ATB3-050T
50
46,0
2,85
2,29
4
ATB3-063T
63
58,8
2,85
3,04
3
ATB3-080T
80
74,8
2,85
4,78
2
Obj. č.
Vnější Ø (mm)
Vnitřní Ø (mm)
Délka (cm)
Hmotnost (kg/ks)
Balení (ks)
ATZ-020
20
17,4
50
0,58
5
ATZ-025
25
22,3
50
0,76
5
Obj. č.
> Dvojitě zahnutá trubka (50 cm)
15,0 cm
50,0 cm
7
Dvakrát zahnutá hliníková trubka je dodávána o délce 50 cm a je určena pro eliminaci odskoku páteřního vedení od stěny při vytváření svodů.
TVAROVKY PŘÍMÉ SPOJKY > Přímé spojky Obj. č.
Vnější rozměr trubky (mm)
Délka (mm)
Šířka (mm)
Hmotnost (kg/ks)
Balení (ks)
APUC-20
20
127,6
37,5
0,07
1
APUC-25
25
138,1
43,5
0,10
1
APUC-40
40
208,8
67,7
0,35
1
APUC-50
50
239,0
83,9
0,63
1
APUC-63
63
182,00
89,0
0,85
1
APUC-80
80
232,0
113,0
1,35
1
APUC-100
100
137,0
138
2,27
1
> Redukované spojky přímé Obj. č. APG-2025
Vnější rozměr trubky (mm)
Redukovaný rozměr trubky (mm)
Délka (mm)
Šířka (mm)
Hmotnost (kg/ks)
Balení (ks)
25
20
132,8
43,5
0,08
1
APG-2540
40
25
173,4
67,8
0,20
1
APG-4050
50
40
223,9
74,0
0,47
1
APG-5063
63
50
201,8
89,0
0,91
1
APG-6380
80
63
222,0
113,0
1,66
1
APG-80100
100
80
304,0
-
1,34
1
KOLENA > Kolena 90° Obj. č.
Vnější rozměr trubky (mm)
Délka (mm)
Šířka (mm)
Hmotnost (kg/ks)
Balení (ks)
APUL-20
20
82,5
37,5
0,07
1
APUL-25
25
95,7
43,5
0,10
1
APUL-40
40
148,3
67,8
0,36
1
APUL-50
50
186,1
83,9
0,70
1
APUL-63
63
168,0
89,0
1,02
1
APUL-80
80
214,0
113,0
2,31
1
APUL-100
100
252,0
-
1,23
1
Vnější rozměr trubky (mm)
Délka (mm)
Šířka (mm)
Hmotnost (kg/ks)
Balení (ks)
> Kolena 45° Obj. č. APUL45-20
20
109,1
37,5
0,07
1
APUL45-25
25
127,9
43,5
0,09
1
APUL45-40
40
148,3
67,8
0,35
1
APUL45-50
50
194,6
83,9
1,65
1
APUL45-63
63
240,8
89,0
1,10
1
APUL45-80
80
278,0
113,0
2,30
1
APUL45-100
100
287,0
-
1,27
1
8
TVAROVKY T-KUSY > T-kusy Obj. č.
Vnější rozměr trubky (mm)
Délka (mm)
Šířka (mm)
Hmotnost (kg/ks)
Balení (ks)
APUT-20
20
127,6
82,6
0,10
1
APUT-25
25
147,9
95,7
0,14
1
APUT-40
40
228,8
148,3
0,53
1
APUT-50
50
289,0
186,1
1,02
1
APUT-63
63
247,0
182,0
1,42
1
APUT-80
80
315,0
232,0
3,22
1
APUT-100
100
304,0
202,0
1,42
1
Hlavní rozměr / odbočka (mm)
Délka (mm)
Šířka (mm)
Hmotnost (kg/ks)
Balení (ks)
25 / 20 25 40 /4020
148,0 20 25228,8
90,5
0,13
APTG-4050
40 /5025 63 50 / 20 80 50 /100 25 50 /100 40
40228,8 50 289,0 63 80289,0 63289,0
APTG-5063
63 /100 50
50250,0
230,0
45 0,40 72 0,41 89 193 0,73 204 0,74 227 0,84 227 1,61 227
1 1 1 11 1 1 1 11 1 11
APTG-6380
80 / 63
318,0
203,0
3,15
1
APTG-50100
100 / 50
304,0
227,0
1,25
1
> Redukované T-kusy Obj. č. APTG-2025 APTG-2040 APTG-2540 APTG-2050 APTG-2550
Délka 155 249 286 251 233 304 304 304
112,7 117,9 130,6 135,9 151,3
APTG-63100
100 / 63
304,0
227,0
1,25
1
APTG-80100
100 / 80
304,0
252,0
1,42
1
Hlavní rozměr / odbočka-závit (mm)
Délka (mm)
Šířka (mm)
Hmotnost (kg/ks)
Balení (ks)
APTF-3820
20 / 3/8“
127,6
86,4
0,13
1
APTF-1220
20 / ½“
127,6
86,4
0,40
1
APTF-1225
25 / ½“
148,0
94,8
0,41
1
APTF-3425
25 / 3/4“
148,0
94,8
0,73
1
APTF-1040
40 / 1“
228,8
138,9
0,60
1
APTF-1050
50 / 1“
289,0
135,9
0,74
1
APTF-2063
63 / 2“
289,0
151,3
0,84
1
APTF-2580
80 / 2,5“
250,0
230,0
1,61
1
APTF-3080
80 / 3“
318,0
203,0
3,15
1
APTF-10100
100 / 1“
304,0
227,0
1,25
1
> Redukované T-kusy s vnitřním trubkovým závitem Obj. č.
9
TVAROVKY ODBOČKY > Odbočky se spojkami Hlavní rozměr / odbočka (mm)
Délka (mm)
Šířka (mm)
Hmotnost (kg/ks)
Balení (ks)
AQD-2025
25 / 20
103,0
64,0
0,10
1
AQD-2040
40 / 20
119,0
78,0
0,13
1
AQD-2540
40 / 25
125,0
83,0
0,15
1
AQD-2050
50 / 20
131,0
89,0
0,14
1
AQD-2550
50 / 25
136,0
94,0
0,16
1
AQD-2063
63 / 20
143,0
104,0
0,17
1
AQD-2563
63 / 25
148,0
110,0
0,19
1
AQD-2080
80 / 20
163,0
121,0
0,19
1
AQD-2580
80 / 25
168,0
127,0
0,21
1
Hlavní rozměr / odbočka-závit (mm)
Délka (mm)
Šířka (mm)
Hmotnost (kg/ks)
Balení (ks)
25 / ½“
107,0
65,0
0,12
1
Obj. č.
> Odbočky s vnitřním trubkovým závitem Obj. č. AQF-1225 AQF-1240
40 / ¾“
124,0
79,0
0,15
1
AQF-3440
40 / ¾“
124,0
83,0
0,16
1
AQF-1250
50 / ½“
135,0
90,0
0,17
1
AQF-3450
50 / ¾“
135,0
95,0
0,19
1
AQF-1263
63 / ½“
148,0
105,0
0,19
1
AQF-3463
63 / ¾“
148,0
110,0
0,21
1
AQF-1280
80 / ½“
167,0
122,0
0,22
1
AQF-3480
80 / ¾“
167,0
127,0
0,24
1
Odbočky jsou speciálně navrženy pro připojení trubek z hlavní potrubní větve. Tato unikátní konstrukce umožňuje vytvořit odbočku či svod z potrubí v minimálním čase. Odbočení je prováděno ze strany, což zamezuje vniknutí kondenzátu do svodu.
4 3 1
7 6
1
2
3
VRTNÝ OTVOR Umístěn na přesném úhlu 180 ° od spojovacího otvoru, vrtný otvor usnadňuje přípravu potrubí. UPÍNACÍ SVORKA Povolte a utáhněte pro úpravu odbočky kolem potrubí. OZNAČENÍ Ukazují optimální polohu trubky při zajišťování finální pozice.
4
O-KROUŽEK Zajišťuje montáž bez úniků.
5
ROZMĚRY HLAVNÍ VĚTVE Od Ø 25 mm (1") do Ø 80 mm (3").
6
ROZMĚRY ODBOČUJÍCÍ VĚTVE K dispozici ve dvou průměrech: Ø 20 mm (3/4“) a Ø 25 mm (1").
7
MOSAZNÝ VÝSTUP Robustní, určený pro opakovanou montáž (pouze pro odbočky se závitem).
10
TVAROVKY SPOJKY SE ZÁVITY > Hliníkové spojky s vnějším trubkovým závitem Hlavní rozměr / trubkový závit (mm)
Délka (mm)
Šířka (mm)
Hmotnost (kg/ks)
Balení (ks)
APCA-1220
20 / ½“
73,8
34,0
0,06
1
APCA-3420
20 / ¾“
73,8
34,0
0,06
1
APCA-3425
25 / ¾“
86,0
39,0
0,09
1
Obj. č.
APCA-1025
25 / 1“
86,0
39,0
0,09
1
APCA-5440
40 /1 ¼“
127,4
45,0
0,27
1
APCA-1540
40 /1 ½“
127,4
45,0
0,32
1
APCA-1550
50 /1 ½“
141,0
55,0
0,47
1
APCA-2050
50 / 2“
141,0
55,0
0,46
1
APCA-2063
63 / 2“
124,0
82,0
0,69
1
APCA-2563
63 / 2½“
124,0
82,0
0,62
1
APCA-2580
80 / 2 ½“
148,0
97,0
1,02
1
APCA-3080
80 / 3“
148,0
97,0
1,05
1
Obj. č.
Hlavní rozměr (mm)
Délka (mm)
Šířka (mm)
Hmotnost (kg/ks)
Balení (ks)
APP-20
20
58,8
37,5
0,03
1
APP-25
25
69,0
43,5
0,05
1
APP-40
40
99,4
67,8
0,17
1
APP-50
50
119,5
83,9
0,32
1
APP-63
63
149,0
90,0
1,31
1
APP-80
80
155,0
113,0
1,68
1
APP-100
100
270,0
158,0
2,2
1
Hlavní rozměr / trubkový závit (mm)
Délka (mm)
Šířka (mm)
Hmotnost (kg/ks)
Balení (ks)
ASH-1220
20 / ½“
131,8
44,0
0,11
1
ASH-1025
25 / 1“
164,1
68,5
0,27
1
ASH-1540
40 / 1½“
219,4
67,8
0,60
1
ZÁSLEPKY > Záslepky
ROZEBÍRATELNÉ SPOJKY > Rozebíratelné spojky s vnitřním trubkovým závitem Obj. č.
11
ASH-2050
50 / 2“
234,6
83,9
0,69
1
ASH-2563
63 / 2½“
189,0
89,0
2,41
1
ASH-3080
80 / 3“
210,0
113,0
3,64
1
TVAROVKY KONCOVÉ KRABICE > Koncové krabice s trubkovými závity Hlavní rozměr / trubkový závit (mm)
Délka (mm)
Šířka (mm)
Hmotnost (kg/ks)
Balení (ks)
AKK-1220
20 / 3x ½“
104,8
77,0
0,40
1
AKK-1225
25 / 3x ½“
113,5
77,0
0,44
1
Vstupní závit / výstupní závit (mm)
Délka (mm)
Šířka (mm)
Hmotnost (kg/ks)
Balení (ks)
AKKT-1212
½“ / 3x ½“
77,5
77,0
0,35
1
AKKT-1234
¾“ / 3x ½“
77,5
77,0
0,35
1
Hlavní rozměr / trubkový závit (mm)
Délka (mm)
Šířka (mm)
Hmotnost (kg/ks)
Balení (ks)
ASA-3820
20 / 3/8“
45,0
36,0
0,24
1
ASA-1220
20 / ½“
45,0
36,0
0,24
1
ASA-1225
25 / ½“
45,0
41,0
0,30
1
ASA-3425
25 / ¾“
45,0
41,0
0,30
1
ASA-1040
40 / 1“
58,0
61,0
0,40
1
ASA-1550
50 / ½“
80,0
75,0
0,60
1
ASA-2050
50 / 2“
80,0
75,0
0,60
1
Obj. č.
Hlavní rozměr (mm)
Průměr (mm)
Výška (mm)
Balení (ks)
AFG-065
63
185,0
95,0
1
AFG-080
80
200,0
120,0
1
AFG-100
100
240,0
131,0
1
Obj. č.
Obj. č.
REDUKCE > Redukce přímá - trubkový závit Obj. č.
PŘÍRUBY > Příruby
> Příslušenství k přírubám
AFT-065
Ploché těsnění DN65
1
AFT-080
Ploché těsnění DN80
1
AFT-100
Ploché těsnění DN100
1
AFSS-100
Šrouby a matice pro přírubu DN 100
1
12
PŘÍSLUŠENSTVÍ Kulové kohouty > Kulové kohouty – trubka / trubka Obj. č.
Hlavní rozměr (mm)
Délka (mm)
Šířka (mm)
Balení (ks)
ABV-20
20 / 20
131,0
73,0
1
ABV-25
25 / 25
150,0
83,0
1
ABV-40
40 / 40
203,6
114,3
1
ABV-50
50 / 50
236,0
132,0
1
Hlavní rozměr / trubkový závit (mm)
Délka (mm)
Šířka (mm)
Balení ks)
> Kulové kohouty – trubka / závit Obj. č. ABVF-3420
20 / ¾“
92,8
84,7
1
ABVF-1025
25 / 1“
111,9
88,7
1
ABVF-1540
40 / 1½“
151,3
114,3
1
ABVF-2050
50 / 2“
176,2
158,0
1
Hlavní rozměr (mm)
Délka (mm)
Šířka (mm)
Balení (ks)
Klapky > Klapky – trubka / trubka Obj. č. AFV-63
63
239,0
309,5
1
AFV-80
80
292,0
320,0
1
AFV-100
100
52,0
380,0
1
AFV-158
158
62,0
451,0
1
Hlavní rozměr / trubkový závit (mm)
Délka (mm)
Šířka (mm)
Balení (počet tyčí)
AFVF-2563
63 / 2,5“
175,0
218,0
1
AFVF-3080
80 / 3“
203,0
220,0
1
> Klapky – trubkový závit / trubka Obj. č.
13
INSTALACE PROFILY, NOSNÍKY A DRŽÁKY > Držáky na trubky Obj. č.
Hlavní rozměr (mm)
Závit
Hmotnost (kg/ks)
Balení (počet tyčí)
ADT-20
20 / 3/8“
M6
0,01
1
ADT-25
20 / ½“
M6
0,01
1
ADT-40
25 / ½“
M6
0,03
1
ADT-50
25 / ¾“
M6
0,04
1
ADT-63
40 / 1“
M8
0,06
1
ADT-80
50 / ½“
M8
0,11
1
ADT-100
50 / 2“
M10
0,18
1
NÁHRADNÍ DÍLY
14
NÁŘADÍ
15
Rychlé Díky chytrému designu a nízké hmotnosti materiálů může být AIRnet nainstalován rychleji než konvenční systémy.
Snadné AIRnet trubky a spojky jsou sestaveny v několika krocích jediným člověkem, bez potřeby těžké techniky.
Spolehlivé Odolné a antikorozní AIRnet trubky a spojky jsou dodávány s 10-letou zárukou. Nízké tření a bezešvá spojení minimalizují tlakové ztráty.
Váš distributor:
BILLER & BURDA s.r.o. Litvínovická 1469, 370 01Č. Budějovice tel: 387 203 682-3 • fax: 387 203 684 www.billerburda.cz
[email protected]
www.rozvodyvzduchuairnet.cz