Technical data sheet
POLY-GP - CHEMICKá KOTVA POLY-GP Je polyesterová prysky#ice bez obsahu styrenu, speciáln# navržená pro lehké až st#edn# náro#né kotvení v dutých a plných materiálech. Snadno se používá a vyzna#uje se rychlým vytvrzováním. Dobrých výsledk# dosahuje p#i pln#ní základních úkol#, jako nap#íklad kotvení žaluzií, satelitní antény, kotle, radiátory, vrata, garáže. ETA-13/0415, CZ-DoP-e13-0415, FDSPOLYGP(1.1)DE, FDS-POLYGP(1.1)UK
FEATURES
Material •
polyesterová prysky#ice bez obsahu styrenu Benefits
• • • •
Rychlé vytvrdnutí minimální zápach neho#lavý produkt dobrá funkce v dutých a plných materiálech
APPLICATIONS Header member • • •
Stavební cihly Plné tvárnice z betonu Porobeton For use with
• • • •
Žaluzie, záv#sy klimatiza#ní jednotky satelitní antény kotle
Tél. : / Fax :
POLY-GP - Chemická kotva POLY-GP
page 1/5
Technical data sheet
POLY-GP - CHEMICKá KOTVA POLY-GP
TECHNICAL DATA
Item codes Art. nr. POLY-GP380-FR
Color Beige
Content [ml] 380
Weight [kg] 0.9
Two nozzles are supplied with each cartridge. Downloadable Safety Data Sheet available from www.strongtie.eu
Performance values (Service loads)
Art. nr.
Poly GP + LMAS M8 Poly GP + LMAS M10 Poly GP + LMAS M12
Solid Brick 0.72 0.72 0.72
Tension [Rds,N] [kN] Autoclaved aerated Hollow Brick concrete blocks 0.26 0.43 0.35 0.43 0.35 0.57
Hollow concrete block
Solid Brick
0.26 0.35 0.35
0.72 0.72 0.72
Shear [Rds,V] [kN] Autoclaved aerated Hollow Brick concrete blocks 0.26 0.43 0.35 0.43 0.35 0.57
Hollow concrete block 0.26 0.35 0.35
1) Performance values are calculated from published data characteristic values in the ETA on which partial safety factors from ETA and a partial coefficient = 1.4 #f actions are applied. Service charges include the sealing position in the holder and is adhered to the method of installation. For hollow brackets unknown resistance, site of trials are needed (in accordance with ICASA recommendations for use by construction professionals for the construction of ankles tests on site).
Tél. : / Fax :
POLY-GP - Chemická kotva POLY-GP
page 2/5
Technical data sheet
POLY-GP - CHEMICKá KOTVA POLY-GP
INSTALLATION Curing Schedule Temp of Support [°C] Working time Curing time
-5°C
0°C
5°C
10°C
15°C
20°C
30°C
25min 4h
15min 3h
12min 2h30
8min 1h15
7min 55min
4min 30min
2min 20min
Drill
Brush.
Insert a sieve.
Feed the hole from the end to the external surface by going back from 1 mixer graduation between each pump.
Insert the treaded rod turning it slowly.
Drill.
Clean the hole brushing and blowing as indicated on the cartridge.
Feed the hole from the end to the external surface by going back from 1 mixer graduation between each pump.
Insert LMAS threaded rod turning it slowly from left to right.
Fix when curing time is reached.
Fix when the curing time is reached.
Solid Brick Installation
Tél. : / Fax :
POLY-GP - Chemická kotva POLY-GP
page 3/5
Technical data sheet
POLY-GP - CHEMICKá KOTVA POLY-GP
Art. nr.
Ø drilling diameter [d0] [mm]
Poly GP + LMAS M8 Poly GP + LMAS M10 Poly GP + LMAS M12
10 12 14
Maximum diameter of hole in the fixture [df] [mm] 9 12 14
Depth of the drilling hole [h1] [mm]
Wrench Size [Sw]
Installation Torque [Tinst] [Nm]
85 85 85
13 15 18
4 6 8
Depth of the drilling hole [h1] [mm]
Wrench Size [Sw]
Installation Torque [Tinst] [Nm]
85 85 85
13 15 18
2 3 5
Depth of Minimum Characteristic the drilling spacing spacing hole [hef] - Smin Scr,N [mm] [mm] [mm] 80 80 80
160 200 240
50 50 50
Characteristic Minimum edge edge distance distance - Ccr,N - Cmin [mm] [mm] 80 50 100 50 120 50
Cellular Concrete
Art. nr.
Ø drilling diameter [d0] [mm]
Poly GP + LMAS M8 Poly GP + LMAS M10 Poly GP + LMAS M12
10 12 14
Maximum diameter of hole in the fixture [df] [mm] 9 12 14
Depth of Minimum Characteristic the drilling spacing spacing hole [hef] - Smin Scr,N [Nm] [mm] [mm] 80 80 80
160 200 240
50 50 50
Characteristic Minimum edge edge distance distance - Ccr,N - Cmin [mm] [mm] 80 50 100 50 120 50
Foundation Brick Installation
Art. nr.
Poly GP + LMAS M8 Poly GP + LMAS M10 Poly GP + LMAS M12
Ø perçage Size of the Sieve [d0] [mm] 16 16 16
16x85 ou 16x130 16x85 ou 16x130 16x85 ou 16x130
Maximum Depth diameter of the of hole drilling in the hole [h1] fixture [mm] [df] [mm] 9 135 12 135 14 135
Depth CharacteristicMinimum Installation of the CharacteristicMinimum Wrench edge edge Torque drilling spacing spacing Size distance distance [Tinst] hole - Scr,N - Smin [Sw] - Ccr,N - Cmin [Nm] [hef] [mm] [mm] [mm] [mm] [mm] 13 4 130 500 100 250 100 15 6 130 500 100 250 100 18 6 130 500 100 250 100
Hollow Cinderblock installation
Tél. : / Fax :
POLY-GP - Chemická kotva POLY-GP
page 4/5
Technical data sheet
POLY-GP - CHEMICKá KOTVA POLY-GP
Art. nr.
Poly GP + LMAS M8 Poly GP + LMAS M10 Poly GP + LMAS M12
Tél. : / Fax :
Ø drilling diameter Size of the Sieve [d0] [mm] 16 16 16
16x130 16x130 16x130
Maximum Depth diameter of the of hole drilling in the hole [h1] fixture [mm] [df] [mm] 9 135 12 135 14 135
Wrench Size [Sw] 13 15 18
Depth CharacteristicMinimum Installation of the CharacteristicMinimum edge edge Torque drilling spacing spacing distance distance [Tinst] hole - Scr,N - Smin - Ccr,N - Cmin [Nm] [hef] [mm] [mm] [mm] [mm] [mm] 4 130 500 100 250 100 6 130 500 100 250 100 6 130 500 100 250 100
POLY-GP - Chemická kotva POLY-GP
page 5/5
