19. ročník - č. 4/2010
URČENÍ PŘETVÁRNÝCH VLASTNOSTÍ A STAVU NAPĚTÍ V PRŮŘEZU OCELOBETONOVÉHO OSTĚNÍ DETERMINATION OF DEFORMATIONAL PROPERTIES AND STATE OF STRESS IN A STEEL-REINFORCED CONCRETE LINING CROSS SECTION KAREL VOJTASÍK, EVA HRUBEŠOVÁ, MAREK MOHYLA, JANA STAŇKOVÁ
ÚVOD Ocelobetonové (OCB) konstrukce primárních ostění podzemních děl, tunelů a kolektorů jsou dnes nejrozšířenější formou stabilizace horninového prostředí, obklopujícího výrub/výlom díla. Použití této technologie k zajištění prostoru výrubu je vhodné zejména v geotechnických podmínkách parciální stability horninového prostředí. Parciální stabilita, krátkodobá autostabilita horninového prostředí je nezbytná pro instalaci ocelobetonové konstrukce ostění. Základem ocelobetonové konstrukce primárních ostění jsou stříkaný beton a dva typy ocelových prvků, které doplňují a napomáhají k naplnění stabilizační role stříkaného betonu. Jsou jimi ocelové rámy, konstruované z prutů různých typů průřezů (příhradové, válcované, svařované, důlní, apod.), a ocelová mřížovina. Ocelové prvky vytváří okamžitou stabilizační reakci. Stříkaný beton integruje ocelové prvky s horninovým masivem. Integrace zajišťuje součinnost konstrukce OCB ostění s horninovým masivem, efektivní využití jak únosnosti konstrukce ostění, tak mobilizaci stabilitního potenciálu horninového prostředí. Stříkaný beton je příčinou, že OCB ostění má proměnlivý charakter, který plyne ze dvou okolností. Prvá je objektivní a souvisí s tuhnutím betonové směsi. Druhá, konstrukční, souvisí s prováděním OCB ostění, kdy stříkaný beton je aplikován postupně, nástřikem ve dvou nebo i několika vrstvách. Mezi nástřikem jednotlivých vrstev je zpravidla 24hodinový časový odstup. Uvedené okolnosti jsou příčinou, že parametry, a tím i únosnost OCB ostění se během výstavby vyvíjí až do okamžiku, kdy je ukončeno tvrdnutí betonu. Tento rys OCB ostění má mimořádný význam pro stabilizaci horninového prostředí. Postupný nárůst tuhosti OCB ostění dovoluje uvolňování napětí z horninového prostředí. Po provedení výlomu a po bezprostředním vybudování ocelobetonového ostění rozhodující roli sehrávají ocelové elementy. Mřížovina zapažuje výrub, ocelové rámy vytvářejí stabilizační reakci. Vrstva stříkaného betonu plní roli dokonalé základky. Nízká tuhost OCB ostění nebrání uvolnění napětí v hornině kolem výlomu díla. Tuhost a únosnost OCB ostění je v tomto okamžiku dána deformačními a pevnostními parametry ocelových elementů. V této fázi zpravidla dochází k významnému uvolnění napětí z horninového prostředí. V dalším průběhu se tvrdnoucí betonová vrstva začíná uplatňovat při vytváření stabilizační reakce OCB ostění. Konec růstu stabilizační reakce OCB ostění je podmíněn ukončením procesu tvrdnutí stříkaného betonu. Pracovní (deformační) charakteristika OCB ostění je dána vývojem tuhosti (modulu pružnosti) průřezu OCB ostění. Navržená metoda je založená na analytických vztazích, které dovolují charakterizovat komplexní vícevrstvou prstencovou strukturu jedinou hodnotou modulu pružnosti. Tato metoda je alternativou standardních teorií posuzování železobetonových průřezů nebo numerických metod, které v protikladu k navrženému analytickému přístupu usilují o postižení všech prvků komplexu v jejich skutečných parametrech. TEORIE SPOLUPRACUJÍCÍCH PRSTENCŮ Algoritmus pro stanovení kvazihomogenního modulu pružnosti kruhového nehomogenního výztužního prstence vychází z analytického
68
INTRODUCTION Steel-reinforced concrete (SRC) structures of primary linings of underground workings, tunnels and utility tunnels are today the most spread form of stabilising a ground environment surrounding excavated openings. The use of this technology for stabilisation of excavation is suitable first of all in the conditions of partial stability of the ground environment. Partial stability, short-term autostability of the ground environment is necessary for the installation of the steel-reinforced concrete lining structure. Basic components of a steel-reinforced concrete primary lining structure are shotcrete and two types of steel elements, which are added to the concrete and help it in fulfilling its stabilisation role. These elements are steel frames constructed from various types of beams (lattice, rolled, welded, colliery etc.) and steel mesh. The steel elements create an immediate stabilisation reaction. Sprayed concrete integrates steel elements with rock mass. The integration secures a composite action of the SRC lining structure with the rock mass, the effective use of both the load-bearing capacity of the lining structure and the mobilisation of the stability potential of the rock mass. The sprayed concrete is the cause why the SRC lining has a variable character following from two conditions. The first one is objective, associated with the process of setting of concrete mix. The other one is structural, associated with the installation of SRC lining, where shotcrete is applied in steps by spraying two or even several layers. A time lag of 24 hours is usually between the applications of individual layers. The above-mentioned circumstances are the cause that the parameters, thus also the load-bearing capacity of the SRC lining, develop till the moment when the concrete setting is finished. This feature of the SRC lining is exceptionally important for the stabilisation of ground environment. The gradual increase in the SRC concrete lining stiffness makes releasing of stress from the ground environment possible. The steel elements play the deciding role after the completion of the excavation and immediately after the erection of the steel-reinforced concrete primary lining. The mesh braces the excavation and the steel frames create a stabilisation reaction. The layer of sprayed concrete fulfils the role of perfect packing. The low stiffness of the SRC lining does not prevent the stress in the ground around the excavated opening from releasing. At this moment, the stiffness and load-bearing capacity of the SRC lining is given by deformational and strength-related parameters of the steel elements. In this phase, significant releasing of stresses from the ground environment usually takes place. During the next course of the process, the hardening shotcrete layer starts to assert itself in the creation of the stabilisation reaction of the SRC lining. The end of the growth of the stabilisation reaction of the SRC lining is conditioned by the end of the sprayed concrete hardening process. The working (deformational) characteristic is given by the development of stiffness (modulus of elasticity) of the SRC lining cross section. The proposed method is based on analytic relationships, which allow the complex multi-layer ring structure to be characterised by a single value of modulus of elasticity. This method is an alternative to standard theories on assessing reinforced concrete sections or numerical methods, which, as opposed to the proposed analytic approach, strive for involving all elements of the complex using real values of the parameters.
19. ročník - č. 4/2010 COACTING RINGS THEORY The algorithm for determining a quasi-homogeneous modulus of elasticity of a circular reinforcing ring is based on an analytical model for calculating a stress-strain state in a multilayer ring, which was formulated by Bulytchev (Bulytchev, 1982). This analytical model uses the theory of analytic functions of a complex variable, the theory of complex potentials and Kolosov functions. The algorithm is based on the assumption that external loads (normal and shear ones) acting on the ring are transferred between individual layers by means of the so-called transfer coefficients, which generally follow from the condition of continuity of deformations at individual contacts between reinforcement layers. These transfer coefficients are functions of the thickness of layers and deformational characteristics of materials of the layers (Poisson’s ratio, elastic modulus). The method is based on the following form of the external load (see Fig. 1): Obr. 1 Základní výpočetní schéma Fig. 1 Basic calculation scheme
modelu pro výpočet napěťo-deformačního stavu ve vícevrstvém kruhovém prstenci, který byl formulován Bulyčevem (Bulytchtev, 1982). Tento analytický model využívá teorii analytických funkcí komplexní proměnné, teorii komplexních potenciálů a funkce Kolosova. Algoritmus vychází z předpokladu, že se vnější zatížení (normálové i smykové) prstence přenáší jednotlivými vrstvami pomocí tzv. přenosových koeficientů, které obecně plynou z podmínky spojitosti deformací na jednotlivých kontaktech vrstev výztuže. Tyto přenosové koeficienty jsou funkcemi tloušťky vrstev a přetvárných charakteristik materiálů vrstev (Poissonovo číslo, modul pružnosti). Metoda vychází z následujícího tvaru vnějšího zatížení (obr. 1):
p0 – radially symmetric component of normal external load p2 – radially asymmetric component of normal external load q2 – component of external tangential load. Stresses pk, qk on individual contacts between layers are defined by means of transfer coefficients by the following relationships:
p0 – radiálně symetrická složka normálového vnějšího zatížení p2 – radiálně nesymetrická složka normálového vnějšího zatížení q2 – složka vnějšího tangenciálního zatížení. Napětí pk, qk na jednotlivých kontaktech vrstev jsou definována pomocí přenosových koeficientů následujícími vztahy:
where K0(i), Kpp(i), Kpqpq(i), Kqp(i),Kqq(i), i=1,…,n are transfer coefficients through the ith layer of reinforcement (transfer coefficients through the first (inner) layer are equal to zero). Tangential stresses and displacements on contacts between the layers correspond to the values of radial stresses on individual contacts between layers expressed in this way. The following relationship applies to the radially symmetric component of displacements on the outer surface of a kth layer:
kde K0(i), Kpp(i), Kpqpq(i), Kqp(i),Kqq(i), i=1,…, n jsou přenosové koeficienty přes i-tou vrstvu výztuže (přenosové koeficienty přes první /vnitřní/ vrstvu jsou rovny nule). Takto vyjádřeným hodnotám radiálních napětí na jednotlivých kontaktech vrstev pak odpovídají tangenciální napětí a posuny na kontaktech vrstev. Pro radiálně symetrickou složku posunů na vnějším povrchu k-té vrstvy platí vztah:
Tangenciální napětí na vnitřním a vnějším obryse výztužního prstence lze vyjádřit následovně: vnitřní obrys k-té vrstvy:
Tangential stresses on the inner and outer contour of the reinforcing ring can be expressed as follows: inner contour of a kth layer:
outer contour of kth layer:
Obr. 2 Schéma dělení ostění na jednotlivé vrstvy Fig. 2 Scheme of the division into individual layers
69
19. ročník - č. 4/2010 where
Obr. 3 Schéma přerozdělení radiálních napětí v nehomogenním prstenci Fig. 3 Scheme of redistribution of radial stresses in an inhomogeneous ring
vnější obrys k-té vrstvy:
kde
Uvedená výpočetní metodika je základem pro stanovení kvazihomogenního modulu pružnosti nehomogenního ostění. Nehomogenní ostění s vnitřními vložkami z odlišného materiálu (např. ocelové vložky) lze totiž rozdělit na jednotlivé dílčí vrstvy, z nichž některé jsou vrstvy homogenní (tři vrstvy označené 1 na obr. 2), některé jsou nehomogenní s pravidelně se střídajícími dílčími tuhostně odlišnými oblastmi (výplň, vložka) (dvě vrstvy označené 2 na obr. 2). Celé toto ostění tak může být považováno za speciální případ vícevrstvého ostění a pro stanovení napěťo-deformačního stavu lze tedy vycházet z již zmíněného algoritmu pro řešení vícevrstvých prstenců. Výpočetní postup pro stanovení kvazihomogenního modulu pružnosti nehomogenního ostění lze rozdělit do dvou dílčích kroků: 1. stanovení dílčího kvazihomogenního modulu pružnosti v jednotlivých dílčích nehomogenních vrstvách, ve kterých jsou instalovány ocelové vložky, 2. stanovení celkového kvazihomogenního modulu pružnosti pro celý prstenec ostění. STANOVENÍ DÍLČÍHO KVAZIHOMOGENNÍHO MODULU PRUŽNOSTI V DÍLČÍ NEHOMOGENNÍ VRSTVĚ Tvar pro vyjádření dílčího kvazihomogenního modulu pružnosti dílčí nehomogenní vrstvy plyne ze základního předpokladu, že radiální posunutí na kontaktních plochách jednotlivých vrstev je identické jak v případě kontaktu s vložkou, tak v případě kontaktu s výplní. Napětí na jednotlivých kontaktech však, na rozdíl od posunů, vykazují nespojitý průběh (obr. 3), v tužších prvcích systému (např. ocelové vložky) s určitým modulem pružnosti Ea se napětí koncentrují, v poddajnějších částech (výplň), charakterizovaných modulem pružnosti o velikosti Eb, jsou napětí nižší (Poissonova čísla považujeme v obou materiálech za identická). Průměrná radiálně symetrická složka normálového napětí pi* v této nehomogenní vrstvě i odpovídá stanovovanému dílčímu kvazihomogennímu smykovému modulu pružnosti G*, napětí pa odpovídající vložkám a napětí pb ve výplni lze dle vztahů Fotievové vyjádřit vztahy:
The above-mentioned calculation method is the basis for the determination of the quasi-homogeneous modulus of elasticity of an inhomogeneous lining. The inhomogeneous lining with internal inserts made of a different material (e.g. steel components) can be divided into individual partial layers; some of them are homogeneous layers (the three layers marked in Fig. 2 as 1), some of them are inhomogeneous with regularly alternating partial areas differing in stiffness (the filling, an insert) (the two layers marked in Fig. 2 as 2). Thus this lining as the whole can be considered to be a special case of a multilayer lining; it is therefore possible for the determination of the stress-strain state to start from the above-mentioned algorithm for solving multilayer rings. The calculation procedure for the determination of the quasihomogeneous modulus of elasticity of an inhomogeneous lining can be divided into two partial steps: 1) the determination of the quasi-homogeneous modulus of elasticity for individual partial inhomogeneous layers in which steel inserts are installed 2) the determination of the overall quasi-homogeneous modulus of elasticity for the entire lining ring DETERMINATION OF QUASI-HOMOGENEOUS MODULUS OF ELASTICITY IN A PARTIAL INHOMOGENEOUS LAYER The form for expressing the partial quasi-homogeneous modulus of elasticity of a partial inhomogeneous layer follows from the basic assumption that radial displacement on contact surfaces between individual layers is identical both in the case of the contact with an insert and in the case of the contact with the filling. However, stresses at individual contacts, as opposed to displacements, exhibit a discontinuous course (see Fig. 3); stresses are concentrated in stiffer elements of the system (e.g. steel inserts) with a certain modulus of elasticity Ea, whilst in more elastic parts (the filling), which are characterised by modulus of elasticity Eb, the stresses ale lower (we consider Poisson’s ratios in both materials to be identical). An average radially symmetric component of normal stress pi* in this inhomogeneous layer even corresponds to the partial quasi-homogeneous shear modulus of elasticity G*. Stress pa corresponding to the inserts and the stress pb in the filling can be expressed according Fotiev relationships by the following relationships:
where K0(G*) is the coefficient of transfer of load through a partial inhomogeneous layer i corresponding to the quasi-homogeneous modulus of elasticity G*and expressions
are redistribution coefficients of average values of radial stresses between the insert and the filling. It follows from the basic initial assumption that displacements on the contact with insert (ua) and the filling material (ub) are identical that:
After putting in
70
19. ročník - č. 4/2010
kde K0(G*) je koeficient přenosu zatížení přes analyzovanou dílčí nehomogenní vrstvu i odpovídající kvazihomogennímu modulu pružnosti G* a výrazy
jsou přerozdělovací koeficienty průměrných hodnot radiálních napětí mezi vložkami a výplní. Ze základního výchozího předpokladu rovnosti posunů na kontaktu s vložkou (ua) i s výplňovým materiálem (ub) plyne: Obr. 4 Etapy provádění průřezu OCB ostění Fig. 4 Stages of the execution of a SRC lining cross section
Po dosazení
Z předchozí rovnice vyplývá vztah pro určení dílčího kvazihomogenního smykového modulu pružnosti G* v dílčí nehomogenní vrstvě, který je váženým průměrem obou modulů Ga a Gb s vahami odpovídajícími příčným rozměrům a, b tuhostně odlišných oblastí:
Stanovení celkového kvazihomogenního modulu pružnosti pro celý prstenec ostění. Postup stanovení celkového kvazihomogenního modulu pružnosti pro celý výztužní prstenec lze charakterizovat následovně: a) homogenizujeme první dvě vnitřní vrstvy výztužního prstence s využitím podmínky, že radiální složka posunů na vnějším obrysu v pořadí druhé vrstvy musí být identická jak v případě, že uvažujeme dvouvrstvý systém s rozdílným modulem pružnosti v každé vrstvě, tak v případě, že uvažujeme jednu vrstvu (její tloušťka je součtem tlouštěk obou dílčích vrstev) s kvazihomogenním modulem pružnosti G*c. Výchozí podmínka pro radiální posun na vnějším poloměru 2. vrstvy má tedy tvar:
A relationship for the determination of a partial quasi-homogeneous shear modulus of elasticity G* in a partial inhomogeneous layer Follows from the above equation. It will be a weighted average of both modules Ga and Gb with the weights corresponding to cross dimensions a, b of the areas differing in the stiffness:
Determination of the overall quasi-homogeneous modulus of elasticity for the entire lining ring The procedure of the determination of the overall quasi-homogeneous modulus of elasticity for the entire lining ring can be characterised as follows: a) we homogenise initial two inner layers of the reinforcing ring using the condition that the radial component of displacement on the outer contour of the second layer in the sequence of layers must be identical both in the case that we take into consideration a double-layer system with differing moduli of elasticity in each layer and in the case that we take into consideration a single layer (the thickness of the layer is a sum of thicknesses of the two partial layers) with quasi-homogeneous modulus of elasticity G*c. The starting condition for the radial displacement on the outer radius of the 2nd layer has the following pattern:
where kde
je radiální posun odpovídající jedné vrstvě s vnitřním poloměrem R0 a vnějším poloměrem R2 charakterizované hledaným celkovým kvazihomogenním modulem pružnosti G*c
je radiální posun odpovídající dvěma vrstvám charakterizovaným moduly pružnosti G1 a G2 S využitím vztahů (1) pro vyjádření hodnot radiálních posunů a po úpravě dostáváme tvar celkového kvazihomogenního smykového modulu pružnosti
is the radial displacement corresponding to a single layer with the inner radius R0 and outer radius R2, which is characterised by the overall quasi-homogeneous modulus of elasticity G*c being sought, while
is the radial displacement corresponding to two layers characterised by moduli of elasticity G1 and G2 Using relationships (1) for expressing the values of radial displacements and after the adaptation we receive the pattern of the overall quasi-homogeneous shear modulus of elasticity.
71
19. ročník - č. 4/2010
Obr. 6 Úvodní strana programu HOMO Fig. 6 Initial page of HOMO program
Obr. 5 Závislost tvrdnutí betonu v čase Fig. 5 Time-concrete hardness curve
K0(G1,G2) – koeficient přenosu zatížení přes druhou vrstvu b) po provedení homogenizace prvních dvou vnitřních vrstev výztuže zavedeme tuto homogenizovanou vrstvu s tloušťkou rovnou součtu tlouštěk obou dílčích vrstev do uvažovaného vícevrstvého systému a proces homogenizace opakujeme dle postupu popsaného výše. Algoritmus pro stanovení celkového kvazihomogenního modulu pružnosti nehomogenního prstence ostění lze tedy formulovat následovně: 1. Rozdělení prstence na určitý počet vrstev homogenních (typ vrstev 1) a určitý počet vrstev nehomogenních (typ vrstev 2). Omezujícími podmínkami pro toto dělení je to, že nesmí následovat dvě nehomogenní vrstvy bezprostředně za sebou, musí být vždy odděleny alespoň jednou homogenní vrstvou (i když o minimální tloušťce). 2. Stanovení příslušných dílčích kvazihomogenních modulů pružnosti pro všechny nehomogenní vrstvy v systému. 3. Určení celkového kvazihomogenního modulu pružnosti pro celý prstenec (metoda postupné homogenizace od vnitřních vrstev k vnějším). Stanovení průběhu tangenciálních napětí v nehomogenním výztužním prstenci Na základě stanoveného modulu pružnosti G*c homogenizovaného prstence lze pak určit tangenciální napětí na vnitřním obrysu R0 a vnějším obrysu Rn homogenizovaného prstence dle vztahů (2) a s využitím předpokladu lineárního průběhu napětí po výšce celého homogenizovaného prstence lze pak stanovit tangenciální napětí σqh v homogenizovaném prstenci na úrovni jednotlivých vrstev v původním (nehomogenizovaném) výztužním prstenci dle následujících vztahů: na úrovni vnitřního poloměru i-té vrstvy:
K0(G1,G2) – coefficient of transfer of load through the second layer b) after homogenising the initial two inner layers of the reinforcement we incorporate this homogenised layer with the thickness equal to a sum of thicknesses of both partial layers into the assumed multilayer system and we repeat the homogenisation process according to the procedure described above. Therefore, the algorithm for the determination of the overall quasi-homogeneous modulus of elasticity of an inhomogeneous lining ring can be formulated as follows: 1) Dividing the ring into a certain number of layers of homogeneous (layer type 2) and certain number of inhomogeneous layers (layer type 1). There are the following conditions limiting this division: two inhomogeneous layers must not follow immediately after one another, they must always be separated at least by one homogeneous layer (even if its thickness is minimised). 2) Determining respective partial quasi-homogeneous moduli of elasticity for all inhomogeneous layers in the system. 3) Determining the overall quasi-homogeneous modulus of elasticity for the entire ring (the method of phased homogenisation from inner layers toward outer ones). Determination of the course of tangential stresses in an inhomogeneous reinforcing ring On the basis of the determined modulus of elasticity G*c of the homogenised ring it is possible to determine tangential stresses on the inner contour R0 and outer contour Rn of the homogenised ring according to relationships (2), and, using the assumption that the course of stress up the height of the entire homogenised ring, it is possible to determine tangential stresses σqh in the homogenised ring at the level of individual layers in the original (non-homogenised) reinforcing ring, using the following relationships: at the level of the inner radius of an ith layer:
at the level of the outer radius of an ith layer: na úrovni vnějšího poloměru i-té vrstvy:
kde
Podíl tangenciálních napětí σq odpovídajících jednotlivým vrstvám v nehomogenním výztužním prstenci a výše uvedených tangenciálních napětí σqh v homogenizovaném prstenci udává nezávisle na
72
where
The proportion of tangential stresses σq corresponding to individual layers in an inhomogeneous reinforcing ring and the
19. ročník - č. 4/2010 Tab. 1 Výsledky výpočtu modulů homogenizovaných průřezů OCB ostění a přerozdělovacích koeficientů tangenciálních napětí v prstencích Table 1 Results of the calculation of moduli of homogenised cross sections of SRC lining and redistribution coefficients of tangential stresses in the rings
Prstenec Ring
Materiál Material
1 Beton Shotcrete 2 Beton Shotcrete ocel *) steel *) 3 Beton Shotcrete 4 Beton Shotcrete 5
Parametry Parameters
1
2
Etapa - Stage 3
4
5
Ebet. [MPa] a1 a2 Ebet. [MPa] a1 a2 a1 a2 Ebet. [MPa] a1 a2 Ebet. [MPa] a1 a2 Ebet. [MPa] a1 a2 a1 a2 Ebet. [MPa] a1 a2
0 0 0 0 0 0 30,031 29,989 0 0 0 10100 1,762 1,761 10100 1,761 1,762 36,543 36,551 10100 1,765 1,766
0 0 0 0 0 0 23,892 23,859 0 0 0 13600 1,830 1,829 13600 1,829 1,830 28,130 28,14 13600 1,832 1,834
13600 0,866 0,865 13600 0,865 0,864 13,355 13,337 13600 0,866 0,865 14600 0,926 0,927 14600 0,927 0,928 13,156 13,159 14600 0,929 0,930
15200 0,893 0,892 15200 0,892 0,890 12,33 12,31 15200 0,892 0,891 15600 0,917 0,918 15600 0,918 0,915 12,14 12,15 15600 0,919 0,920
20300 0,927 0,926 20300 0,926 0,925 9,575 9,562 20300 0,926 0,926 20300 0,927 0,926 20300 0,928 0,929 9,437 9,44 20300 0,930 0,931
above-mentioned tangential stresses σqh in a homo genised ring denotes, independently of external load p0, the so-called coefficient of redistribution of tangential stresses for individual layers for individual layers of the inhomogeneous reinforcing system. Subsequently, these coefficients of redistribution of tangential stresses can be used in situations where only the values of stresses in a homogeneous reinforcing ring are available (e.g. the usual output of numerical models, where the entire reinforcement is modelled as a single reinforcing ring with a certain value of the homogenised modulus of elasticity).
EXAMPLE Beton The following example Shotcrete documents the practical application of the Theory of ocel *) Coacting Rings in the detersteel *) mination of the modulus of 6 elasticity of the SRC lining Beton and determination of the state Shotcrete of stress in the cross section. The SRC lining cross section 6500 8200 15600 17000 22000 Ehomo. [MPa] is reinforced with ASTA 95 steel lattice girder with the *) ocel – E = 210 000 MPa spacing of the girders of 1m; *) steel – E = 210 000 MPa Shotcrete is applied in steps, a1 – přerozdělovací koeficient tangenciálních napětí pro vnitřní vlákna prstence in two layers with identical a1 – redistribution coefficient of tangential stress of the internal lamina rings a2 – přerozdělovací koeficient tangenciálních napětí pro vnější vlákna prstence thicknesses, which are spraya2 – redistribution coefficient of tangential stress of the external lamina rings ed with a time lag of 12 hours. The effect of steel vnějším zatížení p0 tzv. koeficienty přerozdělení tangenciálních mesh is not taken into consideration in the calculation. The calcunapětí pro jednotlivé vrstvy nehomogenního výztužního systému. lation of the SRC lining is divided into 5 stages. Each of the staTyto koeficienty přerozdělení tangenciálních napětí lze pak efektivges corresponds to one characteristic situation existing during the ně využít v situacích, kdy jsou k dispozici pouze hodnoty napětí course of the construction of the SRC lining (see Fig. 4). v homogenním výztužním prstenci (např. obvyklý výstup numericThe time-hardness curve is presented in the chart in Fig. 5. kých modelů, kdy je celá výztuž modelována jako jeden výztužní Current values of the modulus of elasticity of the sprayed concreprstenec s určitou hodnotou homogenizovaného modulu pružnosti). te are read for a particular duration of hardening (the stage) from the chart. PŘÍKLAD The first stage solves the state at the beginning of the construcNásledující příklad dokumentuje praktickou aplikací teorie spotion of the SRC lining, i.e. the erection of the steel frame and bralupracujících prstenců při stanovení modulu pružnosti OCB ostění cing – application of the first layer of shotcrete (1 hour; a stanovení stavu napětí v jeho průřezu. Průřez OCB ostění je konE1v= 10,100MPa). The second stage, the application of the second struován ocelovým příhradovým nosníkem ASTA 95, rozteč prutolayer of shotcrete (1/2 day; E1v= 13,600MPa; E2v= 0MPa). In the vých rámů je jeden metr a stříkaný beton je aplikován postupně, ve third stage (1 day) and fourth stage (2 days) the moduli of elastidvou stejně mocných vrstvách, s provedených s časovým odstupem city of sprayed concrete differ from one another (E1v>E2v). The 12 hodin. Ve výpočtu se neuvažuje s vlivem ocelové mřížoviny. last stage, the fifth one, represents a situation when moduli of Výpočet OCB ostění je rozdělen do 5 etap. Každá etapa odpovídá elasticity in both layers are identical (E1v= E2v) and will no more jedné charakteristické situaci při výstavbě OCB ostění, viz obr. 4. grow (after 28 days). Průběh závislosti tvrdnutí stříkaného betonu na čase uvádí graf na obr. 5. Z tohoto grafu jsou pro daný čas tvrdnutí – etapu, odečRESULTS teny aktuální hodnoty modulu pružnosti stříkaného betonu. The calculation of deformational properties and the state of První etapa řeší stav na počátku výstavby konstrukce OCB stress was carried out using HOMO program (see Fig. 6). This ostění, tj. postavení ocelového rámu a zapažení – nástřik první program was developed for the purpose of conducting practical vrstvy betonu (1 hod; E1v= 10 100MPa). Druhá etapa, nástřik calculations according to the Theory of Coacting Rings. druhé vrstvy stříkaného (½ den; E1v= 13 600MPa; E2v= 0MPa). Results of the calculations are summarised and presented in Ve třetí (1 den) a čtvrté (2 dny) etapě, vrstvy stříkaného betonu Table 1. mají rozdílný modul pružnosti (E1v>E2v.) Poslední, pátá etapa The values of the modulus of elasticity in a homogenised cross představuje situaci, kdy moduly pružnosti v obou vrstvách si section of an SRC lining stages of the SRC lining construction are budou rovny (E1v= E2v) a nebudou se již dále zvyšovat (po 28 presented in the chart in Fig. 7. dnech).
73
19. ročník - č. 4/2010
Obr. 7 Vývoj modulu pružnosti homogenizovaného průřezu OCB ostění Fig. 7 Development of a modulus of elasticity of a homogenised SRC lining cross-section
VÝSLEDKY Výpočet přetvárných vlastností a stavu napětí byl proveden počítačovým programem HOMO (obr. 6). Tento program byl vyvinut za účelem provádění praktických výpočtů, podle teorie spolupracujících prstenců. Výsledky provedených výpočtů jsou shrnuty a uvedeny v tab. 1. Hodnoty modulu pružnosti v homogenizovaném průřezu OCB ostění v jednotlivých etapách výstavby OCB ostění uvádí graf na obr. 7. Graf na obr. 8 uvádí stav napětí v průřezu OCB ostění pro čtvrtou etapu výstavby. Jsou zde zobrazeny průběhy napětí v homogenizovaném průřezu a průběhy napětí ve stříkaném betonu a oceli vypočtené s použitím příslušných přerozdělovacích koeficientů tangenciálních napětí (a1, a2). ZÁVĚR Teorie spolupracujících prstenců a na ní založená homogenizace průřezu vytváří základnu pro exaktní stanovení pracovní charakteristiky OCB ostění a stavu napětí v jeho průřezu, respektující heterogenní strukturu průřezu, časovou proměnlivost modulu pružnosti stříkaného betonu a etapovitost výstavby. Stav napětí v OCB ostění však nezávisí jen na její konstrukci, ale rovněž na chování horninového prostředí, které je do značné míry determinováno pracovní charakteristikou (vývojem tuhosti) ostění. V našem příkladě se s touto eventualitou neuvažovalo a stav napětí v průřezu byl stanoven jenom pro jednu dílčí etapu výstavby OCB ostění a předpoklad konstantní hodnoty zatížení ostění. Předložená metoda dovoluje stanovit vývoj stavu napětí v průběhu všech etap výstavby OCB ostění. Vyžaduje to však znalost interakce mezi horninovým prostředím a ostěním, tato interakce je dána proměnlivou tuhostí ostění. Poděkování Příspěvek byl realizován za finančního přispění Grantové agentury ČR, projekt 103/09/1438 Výzkum pevnostních a přetvárných vlastností ostění ze stříkaného betonu vyztužených tuhými ocelovými prvky.
DOC. ING. KAREL VOJTASÍK, CSc.,
[email protected], DOC. RNDr. EVA HRUBEŠOVÁ, Ph.D.,
[email protected], ING. MAREK MOHYLA,
[email protected], FAKULTA STAVEBNÍ VŠB-TU OSTRAVA, RNDr. JANA STAŇKOVÁ, Ph.D.,
[email protected], HORNICKO-GEOLOGICKÁ FAKULTA VŠB-TU OSTRAVA Recenzoval: doc. Dr. Jan Pruška
Obr. 8 Průběh rozložení napětí v materiálech, betonu a oceli, průřezu OCB ostění pro čtvrtou etapu Fig. 8 Stress distribution in materials, concrete and steel, forming the SRC lining cross section for the fourth stage
The charts in Fig. 8 present the state of stress in the SRC lining cross section for the fourth construction stage. They present the stress distribution in a homogenised cross section and stress distribution in shotcrete and steel, which are calculated using relevant redistribution coefficients of tangential stresses (a1, a2). CONCLUSION The Theory of Coacting Rings and the homogenisation of the cross section based on this theory form a basis for exact determination of the running characteristic of the SRC lining and the state of stress in the cross section which respects the heterogeneous structure of the cross section, the time-varying character of the modulus of elasticity of shotcrete and the division of construction into stages. But the state of stress in the SRC lining depends not only on its structure but also on the behaviour of the ground environment, which is to a significant extent determined by the running characteristic (development of stiffness) of the lining. In our case, this eventuality was not taken into consideration and the state of stress in the cross section was determined only for one partial stage of the SRC lining construction and an assumption of a constant value of the load acting on the lining. The method presented in this paper makes the determination of the development of the state of the interaction between the ground environment and the lining stress during all stages of the SRC lining construction possible. However, it requires knowledge of the interaction between the reaction of the lining; this interaction is given by the variable stiffness of the lining. Acknowledgements This paper was prepared with financial contribution from the Grant Agency of the CR, project 103/09/1438 Research into strength-related and deformational properties of shotcrete linings reinforced with stiff steel elements
DOC. ING. KAREL VOJTASÍK, CSc.,
[email protected], DOC. RNDr. EVA HRUBEŠOVÁ, Ph.D.,
[email protected], ING. MAREK MOHYLA,
[email protected], FAKULTA STAVEBNÍ VŠB-TU OSTRAVA, RNDr. JANA STAŇKOVÁ, Ph.D.,
[email protected], HORNICKO-GEOLOGICKÁ FAKULTA VŠB-TU OSTRAVA
LITERATURA / REFERENCES Bulytchev, N. C. (1982) Mechanika podzemnych sooruženij. Moskva: NEDRA, 270
74