ER.10, ER.11, ER.12, ER.13, ER.15, ER.16
på
!
a
FIBRO Le
Rundschalttische Indexing Tables Otočné indexovací stoly FIBROTOR®
Lh = 16.000 h 2 Wochen / weeks / týdny
ik
Lebensdauer / Service life / Životnost Lieferzeit / Time of delivery / Dodací lhůta
í techn
Le
på
FIBROTOR®-Stärken • Lebensdauer Lh10 = 16000 h (bis zu 120 Mio. Schaltspiele)* • Kurvenrollen mit Gleitlager • Steuerkurve gehärtet und geschliffen • Axial-Nadellagerung mit harten Laufscheiben • Langzeitschmierung
!
ik
FIBROTOR ER. + EM.
a
FIBRO
®
í techn
FIBROTOR®-Strengths • Service life Lh10 = 16,000 h (up to 120 Million cycles)* • C am rollers with slide bearing • H ardened and ground barrel cam • Axial needle bearing with hardened race • Long-term lubrication
FIBROTOR®-přednosti • Životnost stroje Lh10= 16.000 h (až 120 mil. spínacích cyklů)* • Vodicí kladka s kluzným ložiskem • Kalená a broušená drážka šneku • Axiální jehlové uložení s kalenými podložkami • Dlouhodobé mazání
*without motor, overload excepted
*bez motoru, mimo přetížení
*ohne Motor, ausgenommen Überlast
Baureihe ER. / ER. series / Typová řada ER.
günstiger Preis, kurze Lieferzeit / reasonable price, short delivery time / výhodnější cena, krátký dodací termín
Vergleich Baureihe / Comparison series / Srovnání typových řad
ER.
EM.
Teilgenauigkeit / Indexing accuracy / Přesnost polohování Rundlauf / Concentricity / Obvodové házení Planlauf / Flatness / Čelní házení
+ + +
++ ++ ++
Getriebevarianten / Drive variants / Varianty převodu Motorvarianten/ Motor variants / Varianty motoru Teilungsvarianten/ Variants of division / Varianty polohování Sonderteilungen / Special divisions / Speciální počet poloh Flexibles Positionieren / Flexible positioning / Flexibilní nastavení polohy
+ • + • •
++ 0 ++ 0 0
Zusatzbaugruppen / Additional assemblies / Přídavné moduly Sonderausführungen / Special versions / Speciální provedení
+ •
++ 0
Lackierung / Painting / Nátěr
•
0
Lieferzeit / Time of delivery / Dodací lhůta Lebensdauer / Service life / Životnost
++ ++
+ ++
Alle gängigen CAD-Systeme werden unterstützt. 2D- als auch 3D-Daten zur Verfügung./ All standard CAD systems are supported. 2D and 3D data are available./ Podporuje všechny běžné CAD-systémy. 2D i 3D data jsou k dispozici. http://fibro.partserver.de
▶ FIBRO 2
Änderungen vorbehalten / Right of modifications reserved / Změny vyhrazeny
1· 19450·2004·1 ◻
+ = gut / good / dobré ++ = sehr gut / very good / velmi dobré • = nicht möglich / not possible /není možné 0 = möglich / possible / možné
FIBRO
FIBROTOR ® ER. + EM.
a
Le
på
!
ik
í techn
FIBROTOR®-vodicí kladky
FIBROTOR®-Kurvenrollen
FIBROTOR®-Cam followers
• Gleitlagerung • hohe Steifigkeit • optimales Crash-Verhalten • keine Durchbiegung des Außenrings • Flächenpressung zwischen Bolzen und Außenring • höhere Tragzahlen • längere Lebensdauer
• • • • • • •
Kollision
Collision
Kolize
ruch an einer nadelgelagerten Kurvenrolle B nach Kollision. Durchbiegung des Außenrings zwischen den Nadeln. Dieses wird bei FIBROKurvenrollen vermieden.
Example of how a needle bearing can result in failure of a cam follower during a collision. Deflection of the outer ring between the needles. This is avoided with the FIBRO cam followers!
Po kolizi lom na vodící kladce s jehlovým uložením. Průhyb vnějšího kroužku mezi jehlami. Tomuto je možné zabránit pomocí vodících kladek FIBRO!
FIBROTOR®-Getriebe
FIBROTOR®-Gear Unit
FIBROTOR®-převody
• keine elastischen Antriebselemente, die zum Verschleiß neigen • alle Antriebselemente laufen in einem synthetischen Öl • viele Anbaumöglichkeiten
• N o elastic drive elements tending to wear • All drive elements run in a synthetic oil • Many attachment possibilities
• žádné pružné hnací prvky, které by byly náchylné k opotřebení • všechny hnací prvky jsou mazány syntetickým olejem • mnoho nástavbových možností
FIBROTOR®-Schalttellerlagerung
FIBROTOR®-Bearing Advantages
FIBROTOR®-uložení desky stolu
• großdimensionierter Axial-Nadelkranz • mehr Nadeln durch Kunststoffkäfig • höhere Tragzahlen • gehärtete Axialscheiben • Axial-Nadellager mit Kegelrollenlager vorgespannt • hohe Rund- und Planlaufgenauigkeit
• L arge diameter needle bearing assembly • Plastic cage allows maximum number of needles • H igh axial load capacity • H ardened bearing races • Pre-loaded tapered roller bearing • Minimum centre-bore run-out and table top wobble
• vysoce dimenzované axiální jehlové ložisko • více jehel díky kleci ložiska z umělých hmot • vyšší nosnosti • kalené axiální podložky • předepjaté axiální jehlové ložisko s kuželovým ložiskem • vysoká přesnost obvodového a čelního házení
Slide bearing High stiffness Optimized crash characteristics N o deflection of the outer rings S urface pressure between outer ring and bolt Higher capacity Longer lifetime
• kluzné uložení • vysoká tuhost • optimální chování při kolizi • žádný průhyb vnějšího kroužku • měrný tlak mezi čepem a vnějším kroužkem • vyšší nosnosti • delší životnost
Axial-Nadelkranz / Axial needle bearing / Axiální jehlové ložisko Standard Ø 290 x Ø 260 x 5, 56 Nadeln / needles / jehel
1· 19451·2004·1 ◻
FIBRO Ø250 x Ø220 x 5, 92 Nadeln / needles / jehel
Änderungen vorbehalten / Right of modifications reserved / Změny vyhrazeny
▶ FIBRO 3
Le
på
!
ik
FIBROTOR ER.10
a
FIBRO
®
í techn
1. Typkennzeichung / Type designation / Typ FIBROTOR®
ER.10
2. Schaltteller / Table top / Deska stolu
Ø 100 mm
3. Standard-Bremsmotor / Standard brake motor / Standardní brzdový motor 4. Antriebsanordnung / Drive arrangement / Uspořádání pohonu
Feld / Field / Pole 4
siehe Seite 12 / see page 12 / viz. strana 12
.XXX
5. Teilung / Indexing divisions / Počet poloh
Feld / Field / Pole 5
2 - 3 - 4 - 6 - 8 - 12 - 16 - 20 - 24
.XX
6. Zusatzbaugruppen / Additional assemblies / Přídavné moduly
Feld / Field / Pole 7
ohne Zusatzbaugruppen / without additional assemblies / Bez přídavných modulů vertikale Ausführung / vertical version / Vertikální provedení vertikale Ausführung mit Grundplatte / vertical version with base plate / Vertikální provedení se základní deskou ohne Zusatzbaugruppen / without additional assemblies / Bez přídavných modulů Zentrierring / Centring ring / Středicí kroužek Zentrierflansch / Centring flange / Středicí příruba Zentrierring und Zentrierflansch / Centring ring and centring flange / Středicí kroužek a středicí příruba
.0 .3 .4 Feld / Field / Pole 8 .0 .1 .2 .3
7. Genauigkeiten / Accuracies / Přesnosti Teilgenauigkeit / Indexing accuracy / Přesnost polohování in Bogenlänge am [ 100 mm / in length of arc at [ 100 mm / V oblouku na délce [ 100 mm Planlauf / Flatness / Čelní házení Rundlauf der Zentrierbohrung / Concentricity of centring hole / Obvodové házení středicího otvoru Planparallelität / Parallelism / Rovnoběžnost
± 60" ± 0,015 mm 0,02 mm 0,02 mm 0,04 mm
8. Technische Daten / Technical data / Technické údaje Drehrichtung: beliebig, Endschalter eingestellt für rechtsdrehend / Direction of rotation as desired, limit switch set for CW rotation / Směr otáčení: libovolný, koncový spínač nastavený na pravotočivé otáčení Schalthäufigkeit: / Indexing frequency: / Četnost polohování: 40 c/min Spannung / Voltage / Napětí Motor und Bremse / Motor and brake / Motor a brzda 400-460 V 3AC, 50/60 Hz Motorleistung, je nach Schaltzeit / Motor power depending on indexing time / Výkon motoru v závislosti na době zapolohování 0,09 – 0,18 kW Mittendurchgang / Centre hole / Středový otvor Ø 10 mm Arbeitslage beliebig, Standard: horizontal / Working attitude as desired / Pracovní poloha libovolná, standardní: horizontální (andere Einbaulagen bei Bestellung angeben) / (state other mounting attitudes when ordering) / (další montážní polohy uvést při objednávce) Eigengewicht / Weight / Hmotnost ca. 10 kg
9. Schaltzeiten / Indexing Times / Doby zapolohování 50 Hz Teilung / 2 ts [s] Division / J [ kgm2 ] Počet poloh 3 ts [s] J [ kgm2 ] 4 ts [s] J [ kgm2 ] 6 ts [s] J [ kgm2 ] 8 ts [s] J [ kgm2 ] 12 ts [s] J [ kgm2 ] 16 ts [s] J [ kgm2 ] 20 ts [s] J [ kgm2 ] 24 ts [s] J [ kgm2 ]
2,41 2,01 1,81 4,69 3,26 2,64 2,19 1,82 1,64 6,17 4,38 3,55 2,19 1,82 1,64 8,52 6,05 5,00 2,19 1,82 1,64 13,99 9,93 8,30 2,19 1,82 1,64 19,08 13,25 10,97 2,19 1,82 1,64 21,28 15,13 12,55 0,99 0,82 0,74 6,37 4,53 3,79 0,99 0,82 0,74 7,19 5,11 4,28 0,99 0,82 0,74 8,88 6,31 5,29
1,53 1,88 1,39 2,53 1,39 3,57 1,39 5,92 1,39 7,82 1,39 9,57 0,62 2,85 0,62 3,22 0,62 3,98
1,20 1,17 1,09 1,57 1,09 2,22 1,09 3,73 1,09 5,03 1,09 6,16 0,49 1,78 0,49 2,01 0,49 2,48
1,00 0,81 0,91 1,09 0,91 1,54 0,91 2,62 0,91 3,53 0,91 4,28 0,41 1,23 0,41 1,39 0,41 1,72
0,80 0,52 0,73 0,55 0,70 0,39 0,73 0,55 0,99 0,55 0,73 0,55 0,44 1,67 0,94 0,59 0,73 0,55 0,44 0,36 2,28 1,28 0,80 0,56 0,73 0,55 0,44 0,36 2,74 1,54 0,98 0,68 0,33 0,25 0,79 0,44 0,33 0,25 0,89 0,50 0,33 0,25 1,10 0,62
1
2
7
2
3
4
6
8
Ø
5
9
Bearbeitungskraft / Machining forces / Obráběcí síla Transportlast / Transported load / Manipulační zatížení
Bei vertikalem Einsatz und exzentrischer Last Schaltzeittabelle nicht zutreffend / Load diagram does not apply to vertical operation and eccentric load / Při vertikálním použití a mimoosém zatížení neplatí tabulka s dobami zapolohování
10. Belastungsdaten / Load data / Údaje o zatížení
▶ FIBRO 4
horizontal vertikal über Kopf horizontal vertical upside-down horizontální vertikální nad hlavou 100 50 50 520 520 520
a+b c
4000
1500
1500
d
1000
1000
1000
f
350
200
150
g+h
100
100
50
g+h
25
25
25
i
Änderungen vorbehalten / Right of modifications reserved / Změny vyhrazeny
1· 19452·2004·1 ◻
Schaltteller / Table top / Deska stolu zul. Transportlast / perm. transported load / Max. povolené manipulační zatížení kg zul. Aufbautendurchmesser / perm. add-on diameter / Max. povolený průměr nástavby mm zul. axiale Belastung auf Schaltteller / perm. axial loading on table top / Max. povolené axiální zatížení desky stolu N zul. radiale Belastung auf Schaltteller / perm. radial loading on table top / Max. povolené radiální zatížení desky stolu N zul. Kippmoment am positionierten Schaltteller / perm. tilting moment on locked table top / Max. povolený klopný moment zapolohované desky stolu Nm zul. Kippmoment am drehenden Schaltteller / perm. tilting moment on rotating table top / Max. povolený klopný moment na otáčející se desce stolu Nm zul. Tangentialmoment am positionierten Schaltteller / perm. tangential moment on locked table top / Max. povolený tangenciální moment zapolohované desky stolu Nm
FIBRO
FIBROTOR ® ER.10
a
Le
på
!
ik
í techn
11. Baumaße / Installed dimensions / Zástavbové rozměry FIBROTOR ER.10 (Antriebsanordnung 152, für andere Antriebsanordnungen stehen Zeichnungen oder CAD – Daten zur Verfügung) / (Drive arrangement 152, for other drive arrangements drawings or DXF-files are available on request) / (Uspořádání pohonu 152, pro jiná uspořádání pohonu jsou k dispozici výkresy nebo CAD-data)
ø6 H7 x 9 (2x)
ø6,6 (2x)
M6 x 9 (6x) 10 15
M6 (4x)
ø100 ø80
ø47 38 75 100 47
5
60
31 36
X
ø40 ø6,6 (4x)
ø6 H7 (2x)
Befestigungsgewinde / Mounting thread / Připevňovací závit
Einzelheit / Detail / Detail X
Draufsicht Flansch feststehend / Plan view stationary flange / Pohled shora Pevná příruba (Standard)
36 22
Bohrbild für Aufbauten / Hole pattern, for tablemounting fixtures / Schéma rozmístění otvorů pro montáž příslušenství
217
48 48 35 35
53
ø15
25
Zentrierring im Schaltteller / Centring ring on table top / Středicí kroužek desky stolu
30 48 48 58 58 66 66
5
25
ø10
M6 x 11 (3x)
ø112
105 90
ø40 ø30 h7
Zentrierflansch feststehend / Centring flange stationary / Pevná středicí příruba
28
K6
10
M6 x 11
ø50 k6 ø45 k6
17 20
Flansch feststehend / Stationary flange / Pevná příruba (Standard)
Draufsicht Zentrierflansch / Plan view centring flange / Pohled shora Středicí příruba
10 15 65 108
Befestigungsgewinde / Mounting thread / Připevňovací závit 3 x 120°
10
100 105 105
122
Referenzbohrung: Teilung/Bohrbild / Reference hole for Počet poloh and hole pattern / Referenční otvor pro polohování a schéma rozmístění otvorů
Bestellangaben mit Kennziffern: / Ordering information with code No.: / Informace k objednání pomocí kódu č. : ER.10
Feld 1 Field Pole
. 0100 . 1 2
. 3
. 4
. 0 . 5
6
1· 19453·2004·1◻
Massenträgheitsmoment J in kgm2 aus Transportlast / Mass moment of inertia J in kgm2 from transport load/ Moment setrvačnosti J v kgm2 z manipulačního zatížení Schaltzeit ts in Sekunden für Schaltwinkel / Indexing time ts in seconds for indexing angle / Doba zapolohování ts v sekundách pro úhlovou rozteč Änderungen vorbehalten / Right of modifications reserved / Změny vyhrazeny
. 7
8
kgm2 s
▶ FIBRO 5
Le
på
!
ik
FIBROTOR ER.11
a
FIBRO
®
í techn
1. Typkennzeichung / Type designation / Typ FIBROTOR®
ER.11
2. Schaltteller / Table top / Deska stolu
Ø 160 mm
3. Standard-Bremsmotor / Standard brake motor / Standardní brzdový motor 4. Antriebsanordnung / Drive arrangement / Uspořádání pohonu
Feld / Field / Pole 4
siehe Seite 12 / see page 12 / viz. strana 12
.XXX
5. Teilung / Indexing divisions / Počet poloh
Feld / Field / Pole 5
3 - 4 - 6 - 8 - 12 - 16 - 20 - 24
.XX
6. Zusatzbaugruppen / Additional assemblies / Přídavné moduly
Feld / Field / Pole 7
ohne Zusatzbaugruppen / without additional assemblies / Bez přídavných modulů vertikale Ausführung / vertical version / Vertikální provedení vertikale Ausführung mit Grundplatte / vertical version with base plate / Vertikální provedení se základní deskou ohne Zusatzbaugruppen / without additional assemblies / Bez přídavných modulů Zentrierring / Centring ring / Středicí kroužek Zentrierflansch / Centring flange / Středicí příruba Zentrierring und Zentrierflansch / Centring ring and centring flange / Středicí kroužek a středicí příruba
.0 .3 .4 Feld / Field / Pole 8 .0 .1 .2 .3
7. Genauigkeiten / Accuracies / Přesnosti Teilgenauigkeit / Indexing accuracy / Přesnost polohování in Bogenlänge am [ 160 mm / in length of arc at [ 160 mm / V oblouku na délce [ 160 mm Planlauf / Flatness / Čelní házení Rundlauf der Zentrierbohrung / Concentricity of centring hole / Obvodové házení středicího otvoru Planparallelität / Parallelism / Rovnoběžnost
± 40" ± 0,016 mm 0,015 mm 0,015 mm 0,03 mm
8. Technische Daten / Technical data / Technické údaje Drehrichtung: beliebig, Endschalter eingestellt für rechtsdrehend / Direction of rotation as desired, limit switch set for CW rotation / Směr otáčení: libovolný, koncový spínač nastavený na pravotočivé otáčení Schalthäufigkeit: / Indexing frequency: / Četnost polohování: 40 c/min Spannung / Voltage / Napětí Motor und Bremse / Motor and brake / Motor a brzda 400-460 V 3AC, 50/60 Hz Motorleistung, je nach Schaltzeit / Motor power depending on indexing time / Výkon motoru v závislosti na době zapolohování 0,09 – 0,18 kW Mittendurchgang / Centre hole / Středový otvor Ø 22 mm Arbeitslage beliebig, Standard: horizontal / Working attitude as desired / Pracovní poloha libovolná, standardně: horizontální (andere Einbaulagen bei Bestellung angeben) / (state other mounting attitudes when ordering) / (další montážní polohy uvést při objednávce) Eigengewicht / Weight / Hmotnost ca. 20 kg
9. Schaltzeiten / Indexing Times / Doby zapolohování 50 Hz Teilung / 3 ts [s] Division / J [ kgm2 ] Počet poloh 4 ts [s] J [ kgm2 ] 6 ts [s] J [ kgm2 ] 8 ts [s] J [ kgm2 ] 12 ts [s] J [ kgm2 ] 16 ts [s] J [ kgm2 ] 20 ts [s] J [ kgm2 ] 24 ts [s] J [ kgm2 ]
2,78 22,17 2,78 31,61 2,50 41,56 2,50 56,69 2,50 73,46 1,25 20,94 1,25 29,56 1,25 36,50
2,50 18,95 2,50 27,03 2,25 34,42 2,25 46,96 2,25 60,85 1,13 17,35 1,13 24,49 1,13 30,23
2,11 13,51 2,11 19,27 1,90 25,09 1,90 34,23 1,90 44,35 0,95 12,64 0,95 17,85 0,95 22,03
1,79 9,66 1,79 14,07 1,61 18,34 1,61 25,02 1,61 32,42 0,80 9,24 0,80 13,04 0,80 16,10
1,67 1,36 1,07 8,42 5,58 3,47 1,67 1,36 1,07 12,26 8,12 5,06 1,50 1,22 0,96 16,14 10,81 6,73 1,50 1,22 0,96 22,02 14,75 9,19 1,50 1,22 0,96 28,54 19,12 11,91 0,75 0,61 0,48 8,13 5,44 3,39 0,75 0,61 0,48 11,48 7,69 4,79 0,75 0,61 0,48 14,18 9,49 5,91
0,89 2,41 0,89 3,51 0,80 4,67 0,80 6,38 0,80 8,27 0,40 2,35 0,40 3,32 0,40 4,10
0,71 0,54 1,54 0,74 0,71 0,54 2,24 1,25 0,64 0,48 0,39 2,99 1,67 1,07 0,64 0,48 0,39 4,08 2,29 1,46 0,64 0,48 0,39 5,29 2,97 1,89 0,32 1,50 0,32 2,12 0,32 2,62
1
2
7
2
3
4
6
8
Ø
5
9
Bearbeitungskraft / Machining forces / Obráběcí síla Transportlast / Transported load / Manipulační zatížení
Bei vertikalem Einsatz und exzentrischer Last Schaltzeittabelle nicht zutreffend / Load diagram does not apply to vertical operation and eccentric load / Při vertikálním použití a mimoosém zatížení neplatí tabulka s dobami zapolohování
10. Belastungsdaten / Load data / Údaje o zatížení
▶ FIBRO 6
horizontal vertikal über Kopf horizontal vertical upside-down horizontální vertikální nad hlavou 500 200 200 800 800 800
a+b c
8000
3500
3500
d+e
3500
3500
3500
f
750
450
250
g+h
200
200
100
g+h
300
300
300
i
Änderungen vorbehalten / Right of modifications reserved / Změny vyhrazeny
1· 19454·2004·1 ◻
Schaltteller / Table top / Deska stolu zul. Transportlast / perm. transported load / Max. povolené manipulační zatížení kg zul. Aufbautendurchmesser / perm. add-on diameter / Max. povolený průměr nástavby mm zul. axiale Belastung auf Schaltteller / perm. axial loading on table top / Max. povolené axiální zatížení desky stolu N zul. radiale Belastung auf Schaltteller / perm. radial loading on table top / Max. povolené radiální zatížení desky stolu N zul. Kippmoment am positionierten Schaltteller / perm. tilting moment on locked table top / Max. povolený klopný moment zapolohované desky stolu Nm zul. Kippmoment am drehenden Schaltteller / perm. tilting moment on rotating table top / Max. povolený klopný moment na otáčející se desce stolu Nm zul. Tangentialmoment am positionierten Schaltteller / perm. tangential moment on locked table top / Max. povolený tangenciální moment zapolohované desky stolu Nm
FIBRO
FIBROTOR ® ER.11
a
Le
på
!
ik
í techn
11. Baumaße / Installed dimensions / Zástavbové rozměry FIBROTOR ER.11 (Antriebsanordnung 152, für andere Antriebsanordnungen stehen Zeichnungen oder CAD – Daten zur Verfügung) / (Drive arrangement 152, for other drive arrangements drawings or DXF-files are available on request) / (Uspořádání pohonu 152, pro jiná uspořádání pohonu jsou k dispozici výkresy nebo CAD-data) M8 x 14 (4x) M8 x 16 (4x) M6 x 9 (6x)
ø1 60 ø1 08
ø47 57
15
15
ø8 H7 (3x)
12
40
12
100 71
35,4
X
0,6
x 12 (2x) M6 x 9 (2x)
28,6
ø8
ø1 30 ø96
H7
ø9 (4x) 70 14 5
Einzelheit / Detail / Detail X Flansch feststehend / Stationary flange / Pevná příruba (Standard)
ø22 +1
12 1
ø80 k6 ø76 k6 ø75 K6 ø60 ø35
55
18 0 418
Zentrierflansch feststehend / Centring flange stationary / Pevná středicí příruba
Bohrbild für Aufbauten / Hole pattern, for tablemounting fixtures / Schéma rozmístění otvorů pro montáž příslušenství
ø1 23
M5 x 9 (5x)
160 80 69 54
85 93 102
89
34
70 80
5 Zentrierring im Schaltteller / Centring ring on table top / Středicí kroužek desky stolu
Draufsicht Flansch feststehend / Plan view stationary flange / Pohled shora Pevná příruba (Standard)
69
404
16
294 90
M5 x 8 (5x)
Draufsicht Zentrierflansch / Plan view centring flange / Pohled shora Středicí příruba
48 48 69 69 160
ø90
(8,8)
(1 5,2)
266 Referenzbohrung: Teilung/Bohrbild / Reference hole for Počet poloh and hole pattern / Referenční otvor pro polohování a schéma rozmístění otvorů
Bestellangaben mit Kennziffern: / Ordering information with code No.: / Informace k objednání pomocí kódu č. : ER.11
Feld 1 Field Pole
. 0160 . 1 2
. 3
. 4
. 0 . 5
6
1· 19455·2004·1 ◻
Massenträgheitsmoment J in kgm2 aus Transportlast / Mass moment of inertia J in kgm2 from transport load/ Moment setrvačnosti J v kgm2 z manipulačního zatížení Schaltzeit ts in Sekunden für Schaltwinkel / Indexing time ts in seconds for indexing angle / Doba zapolohování ts v sekundách pro úhlovou rozteč Änderungen vorbehalten / Right of modifications reserved / Změny vyhrazeny
. 7
8
kgm2 s
▶ FIBRO 7
Le
på
!
ik
FIBROTOR ER.12
a
FIBRO
®
í techn
1. Typkennzeichung / Type designation / Typ FIBROTOR®
ER.12
2. Schaltteller / Table top / Deska stolu
Ø 220 mm
3. Standard-Bremsmotor / Standard brake motor / Standardní brzdový motor 4. Antriebsanordnung / Drive arrangement / Uspořádání pohonu
Feld / Field / Pole 4
siehe Seite 12 / see page 12 / viz. strana 12
.XXX
5. Teilung / Indexing divisions / Počet poloh
Feld / Field / Pole 5
2 - 3 - 4 - 6 - 8 - 12 - 16 - 20 - 24
.XX
6. Zusatzbaugruppen / Additional assemblies / Přídavné moduly
Feld / Field / Pole 7
ohne Zusatzbaugruppen / without additional assemblies / Bez přídavných modulů vertikale Ausführung / vertical version / Vertikální provedení vertikale Ausführung mit Grundplatte / vertical version with base plate / Vertikální provedení se základní deskou ohne Zusatzbaugruppen / without additional assemblies / Bez přídavných modulů Zentrierring / Centring ring / Středicí kroužek Zentrierflansch / Centring flange / Středicí příruba Zentrierring und Zentrierflansch / Centring ring and centring flange / Středicí kroužek a středicí příruba
.0 .3 .4 Feld / Field / Pole 8 .0 .1 .2 .3
7. Genauigkeiten / Accuracies / Přesnosti Teilgenauigkeit / Indexing accuracy / Přesnost polohování in Bogenlänge am [ 220 mm / in length of arc at [ 220 mm / V oblouku na délce [ 220 mm Planlauf / Flatness / Čelní házení Rundlauf der Zentrierbohrung / Concentricity of centring hole / Obvodové házení středicího otvoru Planparallelität / Parallelism / Rovnoběžnost
± 35" ± 0,019 mm 0,02 mm 0,02 mm 0,04 mm
8. Technische Daten / Technical data / Technické údaje Drehrichtung: beliebig, Endschalter eingestellt für rechtsdrehend / Direction of rotation as desired, limit switch set for CW rotation / Směr otáčení: libovolný, koncový spínač nastavený na pravotočivé otáčení Schalthäufigkeit: / Indexing frequency: / Četnost polohování: 40 c/min Spannung / Voltage / Napětí Motor und Bremse / Motor and brake / Motor a brzda 400-460 V 3AC, 50/60 Hz Motorleistung, je nach Schaltzeit / Motor power depending on indexing time / Výkon motoru v závislosti na době zapolohování 0,18 – 0,37 kW Mittendurchgang / Centre hole / Středový otvor Teilung / Division / Počet poloh 3 – 5 Ø 35 mm Teilung / Division / Počet poloh 6 – 12 Ø 35 mm Arbeitslage beliebig, Standard: horizontal / Working attitude as desired / Pracovní poloha libovolná, standardně: horizontální (andere Einbaulagen bei Bestellung angeben) / (state other mounting attitudes when ordering) / (další montážní polohy uvést při objednávce) Eigengewicht / Weight / Hmotnost ca. 30 kg
9. Schaltzeiten / Indexing Times / Doby zapolohování 50 Hz
1
2
3
Ø
Teilung / 2 ts [s] 3,06 2,44 1,83 1,57 1,18 0,98 Division / J [ kgm2 ] 35,64 23,29 13,36 10,00 5,60 3,87 Počet poloh 3 ts [s] 2,78 2,22 1,67 1,43 1,07 0,89 0,71 0,54 J [ kgm2 ] 47,88 31,98 18,15 13,46 7,54 5,21 3,38 1,87 2 4 2,78 2,22 1,67 1,43 1,07 0,89 0,71 0,54 4 ts [s] 6 5 J [ kgm2 ] 68,30 45,63 25,91 19,22 10,78 7,46 4,85 2,70 2,50 2,00 1,50 1,29 0,96 0,80 0,64 0,48 0,39 6 ts [s] J [ kgm2 ] 104,06 68,09 39,12 29,35 16,65 11,67 7,44 4,15 2,63 2,50 2,00 1,50 1,29 0,96 0,80 0,64 0,48 0,39 8 ts [s] 7 8 9 J [ kgm2 ] 141,96 92,90 53,39 40,06 22,74 15,94 10,18 5,69 3,62 2,50 2,00 1,50 1,29 0,96 0,80 0,64 0,48 0,39 12 ts [s] J [ kgm2 ] 217,19 142,14 81,70 61,31 34,82 24,42 15,60 8,75 5,57 1,25 1,00 0,75 0,64 0,48 0,40 0,32 0,24 0,19 0,63 0,50 0,38 16 ts [s] J [ kgm2 ] 59,78 39,14 22,75 17,62 10,20 7,06 4,49 2,50 1,57 17,18 10,97 6,14 1,25 1,00 0,75 0,64 0,48 0,40 0,32 0,24 0,19 0,64 0,48 0,40 20 ts [s] Bearbeitungskraft / Machining forces / Obráběcí síla J [ kgm2 ] 84,41 55,27 32,13 24,90 14,42 9,99 6,37 3,55 2,25 25,69 14,42 9,99 Transportlast / Transported load / Manipulační zatížení 1,25 1,00 0,75 0,64 0,48 0,40 0,32 0,24 0,19 0,63 0,50 0,38 24 ts [s] J [ kgm2 ] 104,21 68,24 39,68 30,76 17,82 12,35 7,88 4,40 2,79 29,99 19,17 10,75 Bei vertikalem Einsatz und exzentrischer Last Schaltzeittabelle nicht zutreffend / Load diagram does not apply to vertical operation and eccentric load / Při vertikálním použití a mimoosém zatížení neplatí tabulka s dobami zapolohování
10. Belastungsdaten / Load data / Údaje o zatížení
▶ FIBRO 8
horizontal vertikal über Kopf horizontal vertical upside-down horizontální vertikální nad hlavou 800 300 300 1000 1000 1000
a+b c
12000
5000
5000
d+e
8000
8000
8000
f
2000
1500
600
g+h
600
600
300
g+h
400
400
400
i
Änderungen vorbehalten / Right of modifications reserved / Změny vyhrazeny
1· 19456·2004·1◻
Schaltteller / Table top / Deska stolu zul. Transportlast / perm. transported load / Max. povolené manipulační zatížení kg zul. Aufbautendurchmesser / perm. add-on diameter / Max. povolený průměr nástavby mm zul. axiale Belastung auf Schaltteller / perm. axial loading on table top / Max. povolené axiální zatížení desky stolu N zul. radiale Belastung auf Schaltteller / perm. radial loading on table top / Max. povolené radiální zatížení desky stolu N zul. Kippmoment am positionierten Schaltteller / perm. tilting moment on locked table top / Max. povolený klopný moment zapolohované desky stolu Nm zul. Kippmoment am drehenden Schaltteller / perm. tilting moment on rotating table top / Max. povolený klopný moment na otáčející se desce stolu Nm zul. Tangentialmoment am positionierten Schaltteller / perm. tangential moment on locked table top / Max. povolený tangenciální moment zapolohované desky stolu Nm
FIBRO
FIBROTOR ® ER.12
a
Le
på
!
ik
í techn
11. Baumaße / Installed dimensions / Zástavbové rozměry FIBROTOR ER.12 (Antriebsanordnung 152, für andere Antriebsanordnungen stehen Zeichnungen oder CAD – Daten zur Verfügung) / (Drive arrangement 152, for other drive arrangements drawings or DXF-files are available on request) / (Uspořádání pohonu 152, pro jiná uspořádání pohonu jsou k dispozici výkresy nebo CAD-data)
M8 x 10 (8x) 80
ø1 5
ø1 1 (4x)
ø1 0 H7 (2x)
15
15
53
12
15 0 12 0 116
X
ø47 60 12 0 15 0
M8 x 10 (2x) ø1 0 H7 x 1 0 (2x)
ø260 ø220 ø1 54 1
ø170 ø1 28
ø1 8 Einzelheit / Detail / Detail X Flansch feststehend / Stationary flange / Pevná příruba (Standard)
15 0
ø1 20 k6 ø1 00 k6 ø110 K6 ø80 ø55 H7 ø36 ø36 +1
15
Zentrierflansch feststehend / Centring flange stationary / Pevná středicí příruba
65 15
32 200 495
ø1 38
M6 x 11
25
M6 x 11 90 170
65 80
456
65
Draufsicht Zentrierflansch / Plan view centring flange / Pohled shora Středicí příruba
13 7 15 0
H8
30
ø35
117
7 14 Draufsicht Flansch feststehend / Plan view stationary flange / Pohled shora Pevná příruba (Standard)
Zentrierring im Schaltteller / Centring ring on table top / Středicí kroužek desky stolu
Bohrbild für Aufbauten / Hole pattern, for tablemounting fixtures / Schéma rozmístění otvorů pro montáž příslušenství
ø1 05
12 0 187
(1 9,45)
(19,45)
31 5 Referenzbohrung: Teilung/Bohrbild / Reference hole for Počet poloh and hole pattern / Referenční otvor pro polohování a schéma rozmístění otvorů
Bestellangaben mit Kennziffern: / Ordering information with code No.: / Informace k objednání pomocí kódu č. : ER.12
Feld 1 Field Pole
. 0220 . 1 2
. 3
. 4
. 0 . 5
6
1· 19457·2004·1 ◻
Massenträgheitsmoment J in kgm2 aus Transportlast / Mass moment of inertia J in kgm2 from transport load/ Moment setrvačnosti J v kgm2 z manipulačního zatížení Schaltzeit ts in Sekunden für Schaltwinkel / Indexing time ts in seconds for indexing angle / Doba zapolohování ts v sekundách pro úhlovou rozteč Änderungen vorbehalten / Right of modifications reserved / Změny vyhrazeny
. 7
8
kgm2 s
▶ FIBRO 9
Le
på
!
ik
FIBROTOR ER.13
a
FIBRO
®
í techn
1. Typkennzeichung / Type designation / Typ FIBROTOR®
ER.13
2. Schaltteller / Table top / Deska stolu
Ø 280 mm
3. Standard-Bremsmotor / Standard brake motor / Standardní brzdový motor 4. Antriebsanordnung / Drive arrangement / Uspořádání pohonu
Feld / Field / Pole 4
siehe Seite 12 / see page 12 / viz. strana 12
.XXX
5. Teilung / Indexing divisions / Počet poloh
Feld / Field / Pole 5
2 - 3 - 4 - 6 - 8 - 12 - 16 - 20 - 24
.XX
6. Zusatzbaugruppen / Additional assemblies / Přídavné moduly
Feld / Field / Pole 7
ohne Zusatzbaugruppen / without additional assemblies / Bez přídavných modulů vertikale Ausführung / vertical version / Vertikální provedení vertikale Ausführung mit Grundplatte / vertical version with base plate / Vertikální provedení se základní deskou ohne Zusatzbaugruppen / without additional assemblies / Bez přídavných modulů Zentrierring / Centring ring / Středicí kroužek Zentrierflansch / Centring flange / Středicí příruba Zentrierring und Zentrierflansch / Centring ring and centring flange / Středicí kroužek a středicí příruba
.0 .3 .4 Feld / Field / Pole 8 .0 .1 .2 .3
7. Genauigkeiten / Accuracies / Přesnosti Teilgenauigkeit / Indexing accuracy / Přesnost polohování in Bogenlänge am [ 280 mm / in length of arc at [ 280 mm / V oblouku na délce [ 280 mm Planlauf / Flatness / Čelní házení Rundlauf der Zentrierbohrung / Concentricity of centring hole / Obvodové házení středicího otvoru Planparallelität / Parallelism / Rovnoběžnost
± 30" ± 0,02 mm 0,02 mm 0,02 mm 0,04 mm
8. Technische Daten / Technical data / Technické údaje Drehrichtung: beliebig, Endschalter eingestellt für rechtsdrehend / Direction of rotation as desired, limit switch set for CW rotation / Směr otáčení: libovolný, koncový spínač nastavený na pravotočivé otáčení Schalthäufigkeit: / Indexing frequency: / Četnost polohování: 40 c/min Spannung / Voltage / Napětí Motor und Bremse / Motor and brake / Motor a brzda 400-460 V 3AC, 50/60 Hz Motorleistung, je nach Schaltzeit / Motor power depending on indexing time / Výkon motoru v závislosti na době zapolohování 0,25 – 0,55 kW Mittendurchgang / Centre hole / Středový otvor Teilung / Division / Počet poloh 3 – 5 Ø 35 mm Teilung / Division / Počet poloh 6 – 12 Ø 70 mm Arbeitslage beliebig, Standard: horizontal / Working attitude as desired / Pracovní poloha libovolná, standardně: horizontální (andere Einbaulagen bei Bestellung angeben) / (state other mounting attitudes when ordering) / (další montážní polohy uvést při objednávce) Eigengewicht / Weight / Hmotnost ca. 70 kg
9. Schaltzeiten / Indexing Times / Doby zapolohování 50 Hz
1
2
3
Ø
Teilung / 2 ts [s] 3,36 2,81 2,14 1,81 1,38 1,06 0,90 Division / J [ kgm2 ] 61,31 43,78 26,92 18,77 10,78 6,33 4,54 Počet poloh 3 ts [s] 3,06 2,56 1,94 1,64 1,50 1,25 0,96 0,82 J [ kgm2 ] 82,40 60,15 35,85 25,27 21,03 14,55 8,57 6,17 2 4 6 5 3,06 2,56 1,94 1,64 1,50 1,25 0,96 0,82 0,68 0,48 4 ts [s] J [ kgm2 ] 117,57 84,01 49,61 36,11 30,07 20,82 12,31 8,88 6,00 2,93 2,75 2,30 1,75 1,48 1,35 1,13 0,87 0,74 0,61 0,43 0,39 6 ts [s] J [ kgm2 ] 231,79 165,69 97,92 71,34 59,44 41,21 24,45 17,68 12,00 5,96 4,77 7 2,75 2,30 1,75 1,48 1,35 1,13 0,87 0,74 0,61 0,43 0,39 8 ts [s] 8 9 J [ kgm2 ] 302,18 216,24 129,37 93,31 81,15 56,29 33,42 24,19 16,45 8,20 6,44 2,75 2,30 1,75 1,48 1,35 1,13 0,87 0,74 0,61 0,43 0,39 12 ts [s] J [ kgm2 ] 462,34 330,88 198,00 142,84 124,23 86,21 51,22 37,12 25,26 12,66 9,96 1,38 1,15 0,88 0,74 0,68 0,56 0,43 0,37 0,31 16 ts [s] J [ kgm2 ] 130,19 93,16 55,71 41,93 36,03 24,96 14,77 10,66 7,21 1,38 1,15 0,88 0,74 0,68 0,56 0,43 0,37 0,31 20 ts [s] Bearbeitungskraft / Machining forces / Obráběcí síla J [ kgm2 ] 183,85 131,57 78,72 59,26 50,94 35,31 20,93 15,14 10,27 1,38 1,15 0,88 0,74 0,68 0,56 0,43 0,37 0,31 24 ts [s] Transportlast / Transported load / Manipulační zatížení J [ kg m2 ] 226,98 162,45 97,21 73,20 62,92 43,63 25,89 18,73 12,72 Bei vertikalem Einsatz und exzentrischer Last Schaltzeittabelle nicht zutreffend / Load diagram does not apply to vertical operation and eccentric load / Při vertikálním použití a mimoosém zatížení neplatí tabulka s dobami zapolohování
10. Belastungsdaten / Load data / Údaje o zatížení
▶ FIBRO 10
horizontal vertikal über Kopf horizontal vertical upside-down horizontální vertikální nad hlavou 1000 400 400 1400 1400 1400
a+b c d+e
16000
6000
6000
10000
10000
10000
2500
1500
800
g+h
800
800
400
g+h
600
600
600
i
f
Änderungen vorbehalten / Right of modifications reserved / Změny vyhrazeny
1· 19458·2004·1 ◻
Schaltteller / Table top / Deska stolu zul. Transportlast / perm. transported load / Max. povolené manipulační zatížení kg zul. Aufbautendurchmesser / perm. add-on diameter / Max. povolený průměr nástavby mm zul. axiale Belastung auf Schaltteller / perm. axial loading on table top / Max. povolené axiální zatížení desky stolu N zul. radiale Belastung auf Schaltteller / perm. radial loading on table top / Max. povolené radiální zatížení desky stolu N zul. Kippmoment am positionierten Schaltteller / perm. tilting moment on locked table top / Max. povolený klopný moment zapolohované desky stolu Nm zul. Kippmoment am drehenden Schaltteller / perm. tilting moment on rotating table top / Max. povolený klopný moment na otáčející se desce stolu Nm zul. Tangentialmoment am positionierten Schaltteller / perm. tangential moment on locked table top / Max. povolený tangenciální moment zapolohované desky stolu Nm
FIBRO
FIBROTOR ® ER.13
a
Le
på
!
ik
í techn
11. Baumaße / Installed dimensions / Zástavbové rozměry FIBROTOR ER.13 (Antriebsanordnung 152, für andere Antriebsanordnungen stehen Zeichnungen oder CAD – Daten zur Verfügung) / (Drive arrangement 152, for other drive arrangements drawings or DXF-files are available on request) / (Uspořádání pohonu 152, pro jiná uspořádání pohonu jsou k dispozici výkresy nebo CAD-data)
ø280 ø200
ø1 0 H7 x 1 6
M8 x 13
30
M8 x 13
ø220 ø1 50
12 8
Teilung / Division / Počet poloh Einzelheit / Detail / Detail X 02 - 03 - 04 ø1 20 k6 Zentrierflansch Flansch feststehend / ø1 00 k6 feststehend / Stationary flange / ø110 K6 Centring flange Pevná příruba ø80 stationary / (Standard) ø55 Pevná středicí H7 ø36 příruba ø36 +1 M6 x 11 M6 x 11
ø1 3,5 ø20
242
21 2,5
242
120 106
Bohrbild für Aufbauten / Hole pattern, for tablemounting fixtures / Schéma rozmístění otvorů pro montáž příslušenství
100 14 0
T02 - 03 - 04 = 80 mm T06 - 08 -12 = 90 mm 14
274
270
12 0
Draufsicht Zentrierflansch / Plan view centring flange / Pohled shora Středicí příruba
98
100
40 14
ø6,6
280
190
58
175
"x"
88 35
30
12 0 12 9 14 0
117
25 Draufsicht Flansch feststehend / Plan view stationary flange / Pohled shora Pevná příruba (Standard)
+1
H7
ø1 38
6 15
8 8
ø35
Zentrierring im Schaltteller / Centring ring on table top / Středicí kroužek desky stolu
13 6
70 ø1 2
20
23
103
83 100 14 0
175 13 7
ø1 5 ø47
X
292
Einzelheit / Detail / Detail X Teilung / Division / Počet poloh 06 - 08 - 12 ø170 k6 Zentrierflansch Flansch feststehend / ø1 50 k6 feststehend / Stationary flange / Centring flange ø1 50 K6 Pevná příruba stationary / ø1 20 (Standard) Pevná středicí ø94 přiruba ø76 H7 M8 x 12 M8 x 12
8
8
6 14
25
Referenzbohrung: Teilung/Bohrbild / Reference hole for Počet poloh and hole pattern / Referenční otvor pro polohování a schéma rozmístění otvorů
ø70 +1
1· 19459·2004·1 ◻
Draufsicht Flansch feststehend / Plan view stationary flange / Pohled shora Pevná příruba (Standard)
Zentrierring im Schaltteller / Centring ring on table top / Středicí kroužek desky stolu Draufsicht Zentrierflansch / Plan view centring flange / Pohled shora Středicí příruba ø6,6
Änderungen vorbehalten / Right of modifications reserved / Změny vyhrazeny
Bestellangaben mit Kennziffern: / Ordering information with code No.: / Informace k objednání pomocí kódu č. : ER.13
Feld 1 Field Pole
. 0280 . 1 2
. 3
. 4
. 0 . 5
6
Massenträgheitsmoment J in kgm2 aus Transportlast / Mass moment of inertia J in kgm2 from transport load/ Moment setrvačnosti J v kgm2 z manipulačního zatížení Schaltzeit ts in Sekunden für Schaltwinkel / Indexing time ts in seconds for indexing angle / Doba zapolohování ts v sekundách pro úhlovou rozteč
. 7
8
kgm2 s
▶ FIBRO 11
FIBROTOR ® ER.15 1. Typkennzeichung / Type designation / Typ FIBROTOR® 2. Schaltteller / Table top / Deska stolu 3. Standard-Bremsmotor / Standard brake motor / Standardní brzdový motor 4. Antriebsanordnung / Drive arrangement / Uspořádání pohonu
ER.15 Ø 410 mm Feld / Field / Pole 4 .XXX
siehe Seite 16 / see page 16 / viz. strana 16 2 - 3 - 4 - 6 - 8 - 12 - 16 - 20 - 24
5. Teilung / Indexing divisions / Počet poloh
Feld / Field / Pole 5 .XX
6. Zusatzbaugruppen / Additional assemblies / Přídavné moduly ohne Zusatzbaugruppen / without additional assemblies / Bez přídavných modulů vertikale Ausführung / vertical version / Vertikální provedení vertikale Ausführung mit Grundplatte / vertical version with base plate / Vertikální provedení se základní deskou ohne Zusatzbaugruppen / without additional assemblies / Bez přídavných modulů Zentrierring / Centring ring / Středicí kroužek Zentrierflansch / Centring flange / Středicí příruba Zentrierring und Zentrierflansch / Centring ring and centring flange / Středicí kroužek a středicí příruba
Feld / Field / Pole 7 .0 .3 .4 Feld / Field / Pole 8 .0 .1 .2 .3
7. Genauigkeiten / Accuracies / Přesnosti
Teilgenauigkeit T02 - T12 / Indexing accuracy T02 - T12 / Přesnost polohování T02 - T12 Teilgenauigkeit T16 - T24 / Indexing accuracy T16 - T24 / Přesnost polohování T16 - T24 in Bogenlänge am [ 410 mm T02 - T12 / in length of arc at [ 410 mm T02 - T12 / V oblouku na délce [ 410 mm T02 - T12 in Bogenlänge am [ 410 mm T16 - T24 / in length of arc at [ 410 mm T16 - T24 / V oblouku na délce [ 410 mm T16 - T24 Planlauf / Flatness / Čelní házení Rundlauf der Zentrierbohrung / Concentricity of centring hole / Obvodové házení středicího otvoru Planparallelität / Parallelism /Rovnoběžnost
± 20" ± 40" ± 0,02 mm ± 0,04 mm 0,03 mm 0,03 mm 0,06 mm
8. Technische Daten / Technical data / Technické údaje
Drehrichtung: beliebig, Endschalter eingestellt für rechtsdrehend / Direction of rotation as desired, limit switch set for CW rotation / Směr otáčení: libovolný, koncový spínač nastavený na pravotočivé otáčení Schalthäufigkeit: / Indexing frequency: / Četnost polohování: 40 c/min Schalt-Haltewinkel / Index / dwell angle / Skutečné otočení stolu Teilung / Division / Počet poloh 2 330° Teilung / Division / Počet poloh 3 - 5 300° Teilung / Division / Počet poloh 6 - 12 270° Teilung / Division / Počet poloh 16 - 24 135° Spannung / Voltage / Napětí Motor und Bremse / Motor and brake / Motor a brzda 400-460 V 3AC, 50/60 Hz Motorleistung, je nach Schaltzeit / Motor power depending on indexing time / Výkon motoru v závislosti na době zapolohování 0,25 – 1,5 kW Mittendurchgang / Centre hole / Středový otvor Ø 70 mm Arbeitslage beliebig, Standard: horizontal / Working attitude as desired / Pracovní poloha libovolná, standardně: horizontální (andere Einbaulagen bei Bestellung angeben) / (state other mounting attitudes when ordering) / (další montážní polohy uvést při objednávce) Eigengewicht / Weight / Poids ca. 100 kg
9. Schaltzeiten / Indexing Times / Doby zapolohování 50 Hz
1
2
3
Ø
Teilung / 2 ts [s] 5,13 4,38 3,90 3,35 2,86 2,54 2,26 2,18 1,86 1,50 1,28 1,13 Division / J [ kgm2 ] 553 403 318 248 180 142 112 104 75,7 49,0 35,1 27,4 Počet poloh 3 ts [s] 4,67 3,99 3,54 3,04 2,60 2,31 2,05 1,98 1,69 1,37 1,16 1,04 0,88 J [ kgm2 ] 743 572 452 333 250,3 197,7 155,4 144,5 105,2 68,3 49,0 38,9 28,1 2 4,67 3,99 3,54 3,04 2,60 2,31 2,05 1,98 1,69 1,37 1,16 1,04 0,88 4 ts [s] 4 6 5 2 J [ kgm ] 1177 859 679 500 365 288 226 210 153 99,8 71,8 57,0 41,3 4,20 3,19 2,78 2,37 2,11 1,87 1,81 1,54 1,25 1,04 0,93 0,79 0,74 0,65 0,62 0,56 6 ts [s] J [ kgm2 ] 1864 1209 969 729 576 453 421 307 200 140 111 79,9 70,0 53,5 49,4 40,0 4,20 3,19 2,78 2,37 2,11 1,87 1,81 1,54 1,25 1,04 0,93 0,80 0,75 0,65 0,63 0,56 7 8 ts [s] 8 9 J [ kgm2 ] 1907 1558 1252 964 786 619 575 419 273 191 152 111 97,2 74,4 68,7 54,9 4,30 3,26 2,91 2,48 2,21 1,96 1,89 1,64 1,25 1,06 0,96 0,82 0,77 0,67 0,65 0,57 12 ts [s] J [ kgm2 ] 2764 1793 1504 1131 894 704 654 492 284 205 168 122 107 82 76 60 2,15 1,63 1,37 1,17 1,04 0,92 0,89 0,78 0,63 0,53 0,47 0,40 0,37 16 ts [s] J [ kgm2 ] 1232 752 560 420 332 261 243 187 122 85,5 67,9 47,9 41,9 2,15 1,63 1,37 1,17 1,04 0,92 0,89 0,78 0,63 0,53 0,47 0,40 0,37 20 ts [s] Bearbeitungskraft / Machining forces / Obráběcí síla J [ kgm2 ] 1740 1062 790 595 469 369 343 265 173 121 96,3 68,0 59,5 Transportlast / Transported load / Manipulační zatížení 2,15 1,63 1,37 1,17 1,04 0,92 0,89 0,78 0,63 0,53 0,47 0,40 0,37 24 ts [s] J [ kgm2 ] 1459 891 662 498 394 309 288 222 145 101 80,6 56,8 49,7 Bei vertikalem Einsatz und exzentrischer Last Schaltzeittabelle nicht zutreffend / Load diagram does not apply to vertical operation and eccentric load / Při vertikálním použití a mimoosém zatížení neplatí tabulka s dobami zapolohování
10. Belastungsdaten / Load data / Údaje o zatížení
▶ FIBRO 12
horizontal vertikal über Kopf horizontal vertical upside-down horizontální vertikální nad hlavou 2500 600 600 2000 2000 2000
a+b c d+e
25000
9000
9000
15000
15000
15000
6000
3000
1500
g+h
2000
2000
700
g+h
1200
1200
1200
f
i
Änderungen vorbehalten / Right of modifications reserved / Změny vyhrazeny
1· 19458·2004·1 ◻
Schaltteller / Table top / Deska stolu zul. Transportlast / perm. transported load / Max. povolené manipulační zatížení kg zul. Aufbautendurchmesser / perm. add-on diameter / Max. povolený průměr nástavby mm zul. axiale Belastung auf Schaltteller / perm. axial loading on table top / Max. povolené axiální zatížení desky stolu N zul. radiale Belastung auf Schaltteller / perm. radial loading on table top / Max. povolené radiální zatížení desky stolu N zul. Kippmoment am positionierten Schaltteller / perm. tilting moment on locked table top / Max. povolený klopný moment zapolohované desky stolu Nm zul. Kippmoment am drehenden Schaltteller / perm. tilting moment on rotating table top / Max. povolený klopný moment na otáčející se desce stolu Nm zul. Tangentialmoment am positionierten Schaltteller / perm. tangential moment on locked table top / Max. povolený tangenciální moment zapolohované desky stolu Nm
FIBRO
!
a
Le
på
FIBROTOR ® ER.15
ik
í techn
11. Baumaße / Installed dimensions / Zástavbové rozměry FIBROTOR ER.15 (Antriebsanordnung 152, für andere Antriebsanordnungen stehen Zeichnungen oder CAD – Daten zur Verfügung) / (Drive arrangement 152, for other drive arrangements drawings or DXF-files are available on request) / (Uspořádání pohonu 152, pro jiná uspořádání pohonu jsou k dispozici výkresy nebo CAD-data)
Einzelheit / Detail / Detail X Flansch feststehend / Stationary flange / Pevná příruba (Standard)
Zentrierflansch feststehend / Centring flange stationary / Pevná středicí příruba
Bohrbild für Aufbauten / Hole pattern, for tablemounting fixtures / Schéma rozmístění otvorů pro montáž příslušenství
Zentrierring im Schaltteller / Centring ring on table top / Středicí kroužek desky stolu Draufsicht Flansch feststehend / Plan view stationary flange / Pohled shora Pevná příruba (Standard)
Draufsicht Zentrierflansch / Plan view centring flange / Pohled shora Středicí příruba
Referenzbohrung: Teilung/Bohrbild / Reference hole for divisions and hole pattern / Referenční otvor pro polohování a schéma rozmístění otvorů
Bestellangaben mit Kennziffern: / Ordering information with code No.: / Informace k objednání pomocí kódu č. : ER.15 . 0410 . 1 .
Feld 1 Field Pole
2
3
. 4
. 0 . 5
6
1· 19459·2004·1 ◻
Massenträgheitsmoment J in kgm2 aus Transportlast / Mass moment of inertia J in kgm2 from transport load/ Moment setrvačnosti J v kgm2 z manipulačního zatížení Schaltzeit ts in Sekunden für Schaltwinkel / Indexing time ts in seconds for indexing angle / Doba zapolohování ts v sekundách pro úhlovou rozteč Änderungen vorbehalten / Right of modifications reserved / Změny vyhrazeny
. 7
8
kgm2 s
▶ FIBRO 13
FIBROTOR ® ER.16 1. Typkennzeichung / Type designation / Typ FIBROTOR® 2. Schaltteller / Table top / Deska stolu 3. Standard-Bremsmotor / Standard brake motor / Standardní brzdový motor 4. Antriebsanordnung / Drive arrangement / Uspořádání pohonu
ER.16 Ø 460 mm Feld / Field / Pole 4 .XXX
siehe Seite 16 / see page 16 / voir page 16 2 - 3 - 4 - 6 - 8 - 12 - 16 - 20 - 24
5. Teilung / Indexing divisions / Počet poloh
Feld / Field / Pole 5 .XX
6. Zusatzbaugruppen / Additional assemblies / Přídavné moduly ohne Zusatzbaugruppen / without additional assemblies / Bez přídavných modulů vertikale Ausführung / vertical version / Vertikální provedení vertikale Ausführung mit Grundplatte / vertical version with base plate / Vertikální provedení se základní deskou ohne Zusatzbaugruppen / without additional assemblies / Bez přídavných modulů Zentrierring / Centring ring / Bague de centrage Zentrierflansch / Centring flange / Středicí příruba Zentrierring und Zentrierflansch / Centring ring and centring flange / Středicí kroužek a středicí příruba
Feld / Field / Pole 7 .0 .3 .4 Feld / Field / Pole 8 .0 .1 .2 .3
7. Genauigkeiten / Accuracies / Přesnosti
Teilgenauigkeit T02 - T12 / Indexing accuracy T02 - T12 / Přesnost polohování T02 - T12 Teilgenauigkeit T16 - T24 / Indexing accuracy T16 - T24 / Přesnost polohování T16 - T24 in Bogenlänge am [ 460 mm T02 - T12 / in length of arc at [ 460 mm T02 - T12 / V oblouku na délce [ 460 mm T02 - T12 in Bogenlänge am [ 460 mm T16 - T24 / in length of arc at [ 460 mm T16 - T24 / V oblouku na délce [ 460 mm T16 - T24 Planlauf / Flatness / Čelní házení Rundlauf der Zentrierbohrung / Concentricity of centring hole / Obvodové házení středicího otvoru Planparallelität / Parallelism / Rovnoběžnost
± 20" ± 40" ± 0,022 mm ± 0,045 mm 0,03 mm 0,03 mm 0,06 mm
8. Technische Daten / Technical data / Technické údaje
Drehrichtung: beliebig, Endschalter eingestellt für rechtsdrehend / Direction of rotation as desired, limit switch set for CW rotation / Směr otáčení: libovolný, koncový spínač nastavený na pravotočivé otáčení Schalthäufigkeit: / Indexing frequency: / Četnost polohování: 40 c/min Schalt-Haltewinkel / Index / dwell angle / Skutečné otočení stolu Teilung / Division / Počet poloh 2 330° Teilung / Division / Počet poloh 3 - 5 300° Teilung / Division / Počet poloh 6 - 12 270° Teilung / Division / Počet poloh 16 - 24 135° Spannung / Voltage / Napětí Motor und Bremse / Motor and brake / Motor a brzda 400-460 V 3AC, 50/60 Hz Motorleistung, je nach Schaltzeit / Motor power depending on indexing time / Výkon motoru v závislosti na době zapolohování 0,37 – 3,0 kW Mittendurchgang / Centre hole / Středový otvor Ø 110 mm Arbeitslage beliebig, Standard: horizontal / Working attitude as desired / Pracovní poloha libovolná, standardně: horizontální (andere Einbaulagen bei Bestellung angeben) / (state other mounting attitudes when ordering) / (další montážní polohy uvést při objednávce) Eigengewicht / Weight / Poids ca. 220 kg
9. Schaltzeiten / Indexing Times / Doby zapolohování 50 Hz
1
2
3
Ø
Teilung / 2 ts [s] 5,25 4,77 3,81 3,37 3,04 2,43 2,13 1,81 1,63 1,44 1,36 1,16 1,06 Division / J [ kgm2 ] 1140 941 601 496 404 257 198 142 115 88,9 79,1 57,8 47,4 Počet poloh 3 ts [s] 4,77 4,33 3,46 3,07 2,79 2,23 1,95 1,65 1,49 1,31 1,23 1,05 0,95 J [ kgm2 ] 1532 1335 852 667 568 362 279 197 160 124 110 79 65 2 4,77 4,33 3,46 3,11 2,83 2,23 1,95 1,66 1,49 1,31 1,23 1,05 0,95 4 ts [s] 4 6 5 2 J [ kgm ] 2427 2004 1280 1031 852 528 406 292 234 181 161 116 95,8 4,29 3,90 3,12 2,80 2,54 2,03 1,78 1,49 1,35 1,18 1,12 0,95 0,86 0,78 0,65 0,55 6 ts [s] J [ kgm2 ] 2610 2290 1549 1318 1122 717 551 385 313 242 216 154 127 104 71,8 51,2 4,29 3,90 3,12 2,84 2,58 2,06 1,78 1,51 1,37 1,18 1,12 0,95 0,87 0,78 0,65 0,55 7 8 ts [s] 8 9 J [ kgm2 ] 2671 2573 1996 1754 1529 1007 752 541 441 331 295 213 176 143 98,6 70,5 4,29 3,90 3,12 2,84 2,58 2,06 1,81 1,54 1,39 1,20 1,13 0,97 0,87 0,79 0,65 0,56 12 ts [s] J [ kgm2 ] 5448 4781 3234 2833 2413 1541 1186 853 695 522 465 337 270 222 154 110 2,15 1,95 1,56 1,42 1,29 1,03 0,90 0,76 0,68 0,60 0,56 0,48 0,43 16 ts [s] J [ kgm2 ] 1650 1394 921 807 687 438 337 235 191 148 128 92,2 75,9 2,15 1,95 1,56 1,42 1,29 1,03 0,90 0,77 0,68 0,60 0,57 0,48 0,43 20 ts [s] Bearbeitungskraft / Machining forces / Obráběcí síla J [ kgm2 ] 2330 1969 1301 1139 970 620 476 342 271 209 186 131 108 Transportlast / Transported load / Manipulační zatížení 2,15 1,95 1,56 1,42 1,29 1,03 0,90 0,77 0,69 0,60 0,57 0,48 0,43 24 ts [s] J [ kgm2 ] 2876 2431 1606 1407 1198 765 588 423 344 258 230 167 133 Bei vertikalem Einsatz und exzentrischer Last Schaltzeittabelle nicht zutreffend / Load diagram does not apply to vertical operation and eccentric load / Při vertikálním použití a mimoosém zatížení neplatí tabulka s dobami zapolohování
10. Belastungsdaten / Load data / Údaje o zatížení
▶ FIBRO 14
horizontal vertikal über Kopf horizontal vertical upside-down horizontální vertikální nad hlavou 4000 800 800 2400 2400 2400
a+b c
32000
11000
11000
d+e
20000
20000
20000
f
9000
4200
2300
g+h
3000
3000
900
g+h
1400
1400
1400
i
Änderungen vorbehalten / Right of modifications reserved / Změny vyhrazeny
1· 19458·2004·1 ◻
Schaltteller / Table top / Deska stolu zul. Transportlast / perm. transported load / Max. povolené manipulační zatížení kg zul. Aufbautendurchmesser / perm. add-on diameter / Max. povolený průměr nástavby mm zul. axiale Belastung auf Schaltteller / perm. axial loading on table top / Max. povolené axiální zatížení desky stolu N zul. radiale Belastung auf Schaltteller / perm. radial loading on table top / Max. povolené radiální zatížení desky stolu N zul. Kippmoment am positionierten Schaltteller / perm. tilting moment on locked table top / Max. povolený klopný moment zapolohované desky stolu Nm zul. Kippmoment am drehenden Schaltteller / perm. tilting moment on rotating table top / Max. povolený klopný moment na otáčející se desce stolu Nm zul. Tangentialmoment am positionierten Schaltteller / perm. tangential moment on locked table top / Max. povolený tangenciální moment zapolohované desky stolu Nm
FIBRO
!
a
Le
på
FIBROTOR ® ER.16
ik
í techn
11. Baumaße / Installed dimensions / Zástavbové rozměry FIBROTOR ER.16 (Antriebsanordnung 152, für andere Antriebsanordnungen stehen Zeichnungen oder CAD – Daten zur Verfügung) / (Drive arrangement 152, for other drive arrangements drawings or DXF-files are available on request) / (Uspořádání pohonu 152, pro jiná uspořádání pohonu jsou k dispozici výkresy nebo CAD-data)
Einzelheit / Detail / Detail X Flansch feststehend / Stationary flange / Pevná příruba (Standard)
Draufsicht Flansch feststehend / Plan view stationary flange / Pohled shora Pevná příruba (Standard)
Zentrierflansch feststehend / Centring flange stationary / Pevná středicí příruba
Bohrbild für Aufbauten / Hole pattern, for tablemounting fixtures / Schéma rozmístění otvorů pro montáž příslušenství
Zentrierring im Schaltteller / Centring ring on table top / Středicí kroužek desky stolu Draufsicht Zentrierflansch / Plan view centring flange / Pohled shora Středicí příruba
Referenzbohrung: Teilung/Bohrbild / Reference hole for divisions and hole pattern / Referenční otvor pro polohování a schéma rozmístění otvorů
Bestellangaben mit Kennziffern: / Ordering information with code No.: / Informace k objednání pomocí kódu č. : ER.16 . 0460 . 1 .
Feld 1 Field Pole
2
3
. 4
. 0 . 5
6
1· 19459·2004·1 ◻
Massenträgheitsmoment J in kgm2 aus Transportlast / Mass moment of inertia J in kgm2 from transport load/ Moment setrvačnosti J v kgm2 z manipulačního zatížení Schaltzeit ts in Sekunden für Schaltwinkel / Indexing time ts in seconds for indexing angle / Doba zapolohování ts v sekundách pro úhlovou rozteč Änderungen vorbehalten / Right of modifications reserved / Změny vyhrazeny
. 7
8
kgm2 s
▶ FIBRO 15
Antriebsanordnungen / Drive arrangements / Uspořádání pohonu Antrieb Seitenlage / Gearbox lateral position / Boční umístění pohonu Getriebe Drehlage / Gearbox drive position/ Poloha převodovky Lage Klemmenkasten / Position of terminal box / Umístění skříně svorkovnice
1 4 2
1 5 2
2
3
1
2
1 6 2
3
1
1 7 2
1 1
2 2
3
3
1 8 2
1 9 2
2
3
1
2
3
1
Antrieb Seitenlage / Gearbox lateral position / Boční umístění pohonu Getriebe Drehlage / Gearbox drive position/ Poloha převodovky Lage Klemmenkasten / Position of terminal box / Umístění skříně svorkovnice
2 4 2 1
2 5 2 3
1
2
2 6 2
3
2
2 7 2 1 1
2
2
3 3
2 8 2
3
2
1
3
2 1· 19462·2004·1 ◻
1
2 9 2
▶ FIBRO 16
Änderungen vorbehalten / Right of modifications reserved / Změny vyhrazeny
Produktübersicht / Product range / Přehled výrobků
FIBRO fertigt Rundschalttische für nahezu jeden Einsatzfall. Fordern Sie die entsprechenden Produktkataloge an. FIBRO produces various models of rotary indexing tables, so users can be sure of finding the ideal solution for any application. Just ask for more information on our full range of rotary indexing tables. FIBRO vyrábí otočné stoly pro téměř každou aplikaci. Vyžádejte si příslušné katalogy výrobků.
FIBROTOR®
FIBROPLAN®
Die Baureihe elektromechanischer Rundschalttische FIBROTOR® EM./EM.NC. ist konzipiert für Arbeitsaufgaben, die schnelle Schaltvorgänge mit optimierten Bewegungsabläufen erfordern. Bei der konstruktiven Auslegung standen, neben dem Erreichen hoher technischer Funktionswerte, Zuverlässigkeit und Lebensdauer im Vordergrund. Bauform, Baugrößen und Leistungsdaten sind sorgfältig abgestuft und ermöglichen eine optimale Geräteauswahl. Durch die universelle konstruktive Auslegung des FIBROTOR® ist der Einsatz als Aufbau- oder Einbau- Rundtisch in horizontaler und vertikaler Lage möglich. Die Qualität der Geräteausführung und die Verwendung von Langzeitschmierstoffen reduzieren Wartungsarbeiten auf ein Minimum. Hohes Qualitätsniveau ist auch bei dieser Rundtisch - Baureihe ein wesentliches Merkmal. Baureihe mit Nenndurchmesser von [100 bis [1250 mm
NC-Rundtische FIBROPLAN® sind gekennzeichnet durch eine CNC-gesteuerte Drehund Positionier-Bewegung. Der Einsatz erfolgt auf Bearbeitungsmaschinen verschiedenster Art, vobei die Steuerungsfunktion für die Drehachse des Rundtisches in der CNC-Steuerung der Maschine beinhaltet ist, oder von einer separaten CNCSteuerung ausgeführt wird. Die moderne Konzeption mit einem starren, mechanischen Aufbau, kombiniert mit hochwertigen Antriebs- und Steuerungselementen, ermöglicht: flexibles Positionieren in beliebig wählbaren Winkelschritten • Positioniergenauigkeiten bei entsprechender Wahl und Anordnung des MessSystems bis ±10” (indirekt, und ±3” (direkt) • hohe Plan- und Rundlaufgenauigkeiten durch vorgespannte, großdimensionierte Axial-Radiallager Baureihe mit Nenndurchmesser von [160 bis [2400 mm in horizontaler und vertikaler Ausführung
FIBROTOR®
FIBROPLAN®
The FIBROTOR® EM./EM.NC. series of electromechanical indexing tables is designed for tasks involving rapid indexing operations with the optimized motion principle. Primary design considerations in addition to the achievement of excellent technical functionability were reliability and durability. Structural form, sizes and performance specifications are carefully incremented, so allowing the customer an optimum choice of equipment. The universal layout of the FIBROTOR® enables it to be used as an add-on or built-in rotary table in the horizontal or vertical attitude. Quality of workmanship and use of long-term lubricants reduce maintenance work to a minimum. High quality is also a significant feature of this series of rotary table. Range is available in any size from [100 to [1250 mm.
The well-graded range of FIBROPLAN® NC-Rotary Tables is characterised by the very extensive capabilities of the rotary table movement and angular positioning, both under full CNC-control. FIBROPLAN® NC-Rotary Tables are used on machine tools of diverse type and description, with the control of their rotational axis provided either by an additional control axis of the machine's CNC, or by a separate CNC-unit for the rotary table itself. FIBROPLAN® Rotary Tables are the result of progressive, non-compromising design concepts, aimed at utmost versatility and operational rigidity. These attributes, together with drive – and control elements of outstanding quality, enable the user to achieve-: • unrestricted rotary positioning in freely selectable sequence and magnitude • positioning accuracies from ± 3" (direct measuring system) to ±10" (indirect measuring system) • high precision in terms of radial and facial runout, due to selected, preloaded radial/ axial combination bearings of the largest possible diameter Range is available in any size from [160 mm to [2400 mm in horizontal and vertical execution
FIBROTOR®
FIBROPLAN® NC-otočné stoly FIBROPLAN® se vyznačují CNC-řízeným otočným a polohovacím pohybem. Využití na obráběcích strojích nejrůznějších druhů, přičemž řízení osy otáčení stolu je součástí CNC-řízení stroje nebo některého separátního CNC-řízení. Moderní koncepce s pevnou mechanickou nástavbou, kombinovaná s velmi kvalitními pohonnými a řídícími prvky, umožňuje flexibilní nastavení polohy v libovolně volitelných úhlových krocích: • Přesnost nastavení polohy při odpovídající volbě a seřízení měřicího systému do ±10” (nepřímé) a ±3” (přímé) • vysoká přesnost čelní a obvodové házivosti díky předepjatým, vysoce dimenzovaným axiálně-radiálním ložiskům Výrobní řada se jmenovitým průměrem od 160 do 2400 mm v horizontálním a vertikálním provedení.
1· 19463·2004·1 ◻
Výrobní řada elektromechanicky otočných stolů FIBROTOR® EM./EM.NC. je navržena pro pracovní činnosti vyžadující rychlé procesy polohování s optimalizovanými postupy činnosti. Mezi konstrukční přednosti patří kromě dosažení vyšších technických funkčních hodnot, také vyšší spolehlivost a životnost. Provedení, velikost a výkonové parametry jsou pečlivě odstupňovány a umožňují optimální výběr přístroje. Univerzální konstrukce FIBROTORu® umožňuje použití otočného stolu jako nástavbu nebo vestavbu v horizontální a vertikální poloze. Kvalita provedení přístroje a dlouhodobé použití maziv snižují údržbu na minimum. Vysoká úroveň kvality je významným atributem také této výrobní řady otočných stolů. Výrobní řada s jmenovitým průměrem od 100 do 1250 mm.
Änderungen vorbehalten / Right of modifications reserved / Změny vyhrazeny
▶ FIBRO 17
Produktübersicht / Product range / Přehled výrobků
FIBROTAKT®
Einbaurundschalttische FIBROTAKT®
Der Rundschalttisch FIBROTAKT ® ist eine bewährte Baureihe, die laufend weiterentwickelt und verbessert wird. Bestimmt für den Einsatz als Schwenk- und Positionierachse in Werkzeugmaschinen, Rundtakt-Maschinen sowie in Produktionsund Fertigungsanlagen verschiedenster Art. Dabei wird der FIBROTAKT ® als Träger von Vorrichtungen und Werkstücken oder als Träger von Werkzeugen verwendet. Kennzeichnend für den FIBROTAKT ® ist das Funktionsprinzip der Verriegelung mit einer Planverzahnung, die hohe Positioniergenauigkeit und große Starrheit bietet. • hohe Teilgenauigkeit bis zu ±1” • hohe Wiederholgenauigkeit (20-30% der Teilgenauigkeit) • große Steifigkeit gegenüber einwirkenden Bearbeitungskräften • hohe Zuverlässigkeit und lange Lebensdauer Baureihe mit Nenndurchmesser von [100 bis [2000 mm
Einbaurundschalttische FIBROTAKT ® mit Planverzahnung sind für den Einsatz in Rundtaktmaschinen konstruiert. Die Bauweise ist aus der bewährten FIBROTAKT ®-Baureihe abgeleitet mit einer Verriegelung des Schalttellers in einer nichtabhebenden Planverzahnung. Daraus und aus weiteren speziellen Ausführungsmerkmalen ergeben sich viele Vorteile für den Anwender: • Gehäuseform rund, Antrieb unten angeordnet • große Starrheit des Schalttellers durch eine Planverzahnung mit max. Durchmesser • hohe Teilgenauigkeit bis zu ±1” • kurze Schaltzeiten bei hohen Massenträgheitsmomenten • Sonderausführungen für spezielle Einsatzfälle Baureihe mit Nenndurchmesser von [345 bis [2500 mm in horizontaler und vertikaler Ausführung
FIBROTAKT®
FIBROTAKT® Flush-Mount Tables
The FIBROTAKT® indexing table is an established range under continuous development and improvement. Produced for use as an indexing axis in machine tools, rotary indexing machines, production and manufacturing systems of various types. The FIBROTAKT® is used to mount fixtures and work pieces or as tool holders. A characteristic of the FIBROTAKT® is the principal function of clamping into a face gear, that affords high indexing accuracy and extreme rigidity. • High indexing accuracy up to ± 1" • High repeatability (20-30% of the indexing accuracy) • High rigidity against applied machining forces • High reliability and long life Range available with nominal diameters from [100 to [2000 mm
FIBROTAKT® Flush-Mount Tables with face gear were developed for use on rotary transfer machines. The concept derives from the well-tried FIBROTAKT® - series and is based on the principle of combining indexing and locking in a non-lifting system of face gear rings. Besides many other special advantages, FIBROTAKT® Flush-Mount Tables offer the following benefits: • housing of uninterrupted round shape. Underslung drive train. • great rigidity, by virtue of locking into face gear rings of largest possible diameter • high indexing accuracy up to ±1" • very fast indexing times with heavy table loads • special designs for specific applications Range available in any size from [345 mm to [2500 mm in horizontal and vertical execution
FIBROTAKT®
Vestavěné otočné stoly FIBROTAKT®
Otočný stůl FIBROTAKT je osvědčenou výrobní řadou, která je průběžně zdokonalována a vylepšována. Je určen pro natáčení polohovací osy v obráběcích strojích, v taktovacích strojích stejně jako ve výrobních zařízení různého typu. Přitom je FIBROTAKT® použit buď jako nosič zařízení a obrobků, nebo jako nosič obrobků. Pro FIBROTAKT® je charakteristický funkční princip zablokování pomocí čelního ozubení, vysoká přesnost nastavení a velká tuhost poskytují: • vysokou přesnost dělení až do ±1" • vysokou opakovatelnou přesnost (20-30% přesnosti dělení) • velkou tuhost vůči působícím obráběcím silám • vysokou spolehlivost a dlouhou životnost Výrobní řada se jmenovitým průměrem od 100 do 2000 mm.
Vestavěné otočné stoly FIBROTAKT ® s čelním ozubením jsou konstruovány pro použití u taktovacích strojů. Výrobní řada je odvozena z osvědčené výrobní řady FIBROTAKT® se zablokováním desky stolu nenadzvedávajícím se čelním ozubením. Z toho i z dalších speciálních vlastností vyplývá mnoho výhod pro uživatele: • kulatý tvar skříně, pohon umístěn vespod • velká tuhost desky stolu díky čelnímu ozubení s max. průměrem • vysoká přesnost dělení až do ±1" • krátké doby indexování při vysokých momentech setrvačnosti • zvláštní provedení pro speciální aplikace Výrobní řada se jmenovitým průměrem od 345 mm do 2500 mm v horizontálním a vertikálním provedení.
1· 19464·2004·1 ◻
®
▶ FIBRO 18
Änderungen vorbehalten / Right of modifications reserved / Změny vyhrazeny
Vertretungen / Representatives / Obchodní zastoupení Normalien Standard Parts Normálie
AT
Rundtische Rotary Tables Otočné stoly
AU
Automation Automation Automatizace
BA
BE DE
PLZ
Walter Ruff GmbH Postfach �� ���� · ����� Bremen Tel. ����-��� ��-� · Fax ����-��� ��-��
[email protected] · www.praeziruff.de �����-�����, �����
PLZ
Außendienst Karl-Heinz Keßler Mehlstraße � · ����� Bielefeld Tel. ����-��� �� · Fax ����-��� �� �� Mobil ����-��� �� �� ·
[email protected] �����-�����, �����, �����
PLZ
Ing. Büro für Automation Dirk Ahke VDI Zum Wenzelnberg �a · ����� Langenfeld Tel. �����-��� ��-� · Fax �����-��� ��-��
[email protected] �����-�����, �����-�����, �����-�����
PLZ
BG
BR
CH
CN
Außendienst Henning Reiner Am Eselsberg �� · ����� Ulm Tel. ����-��� �� ��� · Fax ����-��� �� ��� Mobil ����-�� �� �� �� ·
[email protected] �����, �����-�����, �����-�����, �����-�����
PLZ
Außendienst Roland Grimm Hildegardisstraße 16 · 65343 Eltville Tel. 06123-70 22 05 · Fax 06123-70 22 26 Mobil 0171-229 45 14 ·
[email protected] 55000, 35000, 36000, 60000-68000, 76000
PLZ
Außendienst Peter Finkenbeiner Grüner Weg � · ����� Wildberg Tel. �����-�� �� · Fax �����-�� �� �� Mobil ����-��� �� ��
[email protected] �����, �����, �����-�����, �����-�����
PLZ
Jugard & Künstner GmbH Landsberger Straße ���/l · ����� München Tel. ���-��� �� �� · Fax ���-��� �� ��
[email protected] www.jugard-kuenstner.de �����-�����
PLZ
Jugard & Künstner GmbH Thomas-Mann-Straße �� · ����� Nürnberg Tel. ����-�� �� �� · Fax ����-�� �� ��
[email protected] www.jugard-kuenstner.de �����-�����
PLZ
Außendienst Stefan Schumann Forstweg �� · ����� Weida Tel. ������-��� �� · Fax ������-��� �� Mobil ����-��� �� �� ·
[email protected] �����-�����, �����-�����
CZ
DK
ES
FI
FR
GB
HK
HR
HU
IL
19465 ·· ��/���� 04/2009 ·· �� 90 �1 ·· �����
IN
Änderungen vorbehalten / Right of modifications reserved / Změny vyhrazeny
Rath & Co. Ges. m.b.H. Teiritzstrasse � · ���� Korneuburg Tel. +�� ����-��� · Fax +�� ����-���-��
[email protected] · www.rath-co.at Enmor Tool & Machine Co. Pty. Ltd. Locked Bag ���� · Annandale, NSW ���� Tel. +��-���-���-��� · Fax +��-�-����-����
[email protected] Oro-Tech trgovina d.o.o. Ulica borcev �/b · SI-���� Maribor Tel. +��� �-��� �� �� · Fax +��� �-��� �� ��
[email protected] ZVS Techniek B.V. Grotiuslaan � · NL-���� XM Zwolle Tel. +�� ��-���� ��� · Fax +�� ��-���� ��� Mobil +�� ���� �����
[email protected] · www.zvstechniek.nl FEST-��-EOOD �� A Bulgaria Bul., App. �� · ���� Lovech Tel. + Fax +��� �� ��� ��� z.vasilev_fest_��@abv.bg Prodromus Automacao Modular Av. Gen. Cavalcanti de Albuquerque, ��� Jardim Londrina - CEP �����-��� · São Paulo - SP Tel. +��-��-����-���� · Fax +��-��-����-����
[email protected] FIBRO GmbH Zweigniederlassung Brüggbühlstrasse �� · ���� Niederwangen b. Bern Tel. +�� ��-��� �� �� · Fax +�� ��-��� �� ��
[email protected] · www.fibro.com Forsteppe Asia Ltd. (Shanghai) Co., Ltd. ���-� LuXing Road · Liuzao Town Nanhui County · Shanghai, ������ Tel. +��-��-�� �� �� �� · Fax +��-��-�� �� �� ��
[email protected] · www.forsteppe.com FGC Precision (Guangzhou) Ltd. Flat East, �/F., Block A�, Bei Wei Ind. Area Western Section, GET · Guangzhou, ������ Tel. +��-��-�� �� �� �� · Fax +��-��-�� �� �� ��
[email protected] · www.forsteppe.com SK Technik, spol. s. r. o. Merhautova �� · ����� Brno Tel. +�� � ��� ��� ��� · Fax +�� � ��� ��� ���
[email protected] · www.sktechnik.cz Hoff Vakuumteknik Baunegårdsvej �� · ���� Gentofte Tel. +�� ���� ���� · Fax +�� ���� ����
[email protected] · www.hoff-vakuum.dk Daunert Máquinas-Herramientas, S. A. C/. Tirso de Molina s/n Esquina C/. Albert Einstein Polígono Industrial Almeda ����� Cornellá de Llobregat · Barcelona Tel. +�� ��-��� �� �� · Fax +�� ��-��� �� ��
[email protected] · www.daunert.com OY Christer Lindholm Eng. AB Santalantie ��, PL. �� · ����� Hanko Tel. +���(�)��� ��� ��� Fax +���(�)��� ��� ���
[email protected] · www.clegroup.eu FIBRO France SARL ��/��, rue Jean Lolive · ����� Bagnolet B.P. no ��� · ����� Bagnolet Cedex Tél. +�� �-��-��-��-�� · Fax +�� �-��-��-��-��
[email protected] · www.fibro.com EXPERT TOOLING AND AUTOMATION PRODUCTS � Banner Park, Wickmans Drive Coventry West Midlands CV� �XA Tel. +��(�)�� ���� ���� Fax +��(�)�� ���� ����
[email protected] · www.expertuk.com Forsteppe Asia Ltd. Unit ���, �/F · Shing Chuen Industrial Building ��-�� Shing Wan Road Tai Wai, Shatin, N.T., Hong Kong Tel. +���-�� �� �� �� · Fax +���-�� �� �� ��
[email protected] · www.forsteppe.com Oro-Tech trgovina d.o.o. Ulica borcev �/b · SI-���� Maribor Tel. +��� � ��� �� �� · Fax +��� � ��� �� ��
[email protected] Rath & Co. Ges. m.b.H. Teiritzstraße � · AT-���� Korneuburg Tel. +�� � ���-��� · Fax +�� � ���-���-��
[email protected] · www.rath-co.at A. J. Englander ���� Ltd. �� Harechev Street · Tel Aviv ����� Tel. +��� �-��� �� �� · Fax +��� �-��� �� ��
[email protected] · www.englander.co.il NN Combined Engineering Agencies Pvt. Ltd. Dr. Ranji Block, First Floor ��� M. G. Road · Secunderabad ��� ��� AP Tel. +�� ��-���� �� �� · Fax +�� ��-�� �� �� ��
[email protected] · www.nncea.com
IR
IT
JP
KR
MA
MY
NL
NO
PT
SE
SG
SI
SK
TR
US
ZA
Eximrad Co. ��� Dr. Mofatah Ave. · Tehran ����� Tel. +�� ��-�� ���� �� · Fax +�� ��-�� �� �� ��
[email protected] NC Componenti S.R.L. Via F. Raimondo, ��/B ����� Cascine Vica-Rivoli (TO) Tel. +�� ���-��� �� �� · Fax +�� ���-��� �� ��
[email protected] · www.nccomponenti.it Tomita Co. Ltd. �-��-��, Ohmorinaka, Ohta-ku · Tokio ��� Tel. +�� �-�� �� �� �� · Fax +�� �-�� �� �� ��
[email protected] Jinsung Trading Corp. Dong Wo Bldg. ��� ����-�, �AV Choryang Dong Gu, Pusan Tel. +�� �� ��� ����/� · Fax +�� �� ��� ����
[email protected] Chiba Industrie Bd. Mohamed Bouziane Lot �� Hay My Rachid · Casablanca Tel. +��� �� �� �� �� · Fax +��� �� �� �� ��
[email protected] FIBRO Asia Pte. Ltd. ���, Genting Lane, ���-�� · Singapore ������ Tel. +�� �� �� �� �� · Fax +�� �� �� �� ��
[email protected] · www.fibro.com ZVS Techniek B.V. Grotiuslaan � · ���� XM Zwolle Tel. +�� ��-���� ��� · Fax +�� ��-���� ��� Mobil +�� ���� �����
[email protected] · www.zvstechniek.nl Kaspo Maskin AS Hoeggveien �� · ���� Trondheim Tel. +�� �� �� �� �� · Fax +�� �� �� �� ��
[email protected] · www.kaspo.no Seri Lda. Zona Industrial da Varziela Av. José Ramos Maia – Lote no �, Apartado ��� ����-��� Vila do Conde Tel. +��� ��� �� �� �� · Fax +��� ��� �� �� ��
[email protected] Dankab Verktygsmaskiner AB Box ���� · ����� Lidingö Larsbergsvägen ��b · ����� Lidingö Tel. +�� ��� �� �� �� · Fax +�� ��� �� �� ��
[email protected] · www.dankab.se FIBRO Asia Pte. Ltd. ���, Genting Lane, ���-�� · Singapore ������ Tel. +�� �� �� �� �� · Fax +�� �� �� �� ��
[email protected] · www.fibro.com Oro-Tech trgovina d.o.o. Ulica borcev �/b · SI-���� Maribor Tel. +��� � ��� �� �� · Fax +��� � ��� �� ��
[email protected] SK Technik, spol. s. r. o. Merhautova �� · ����� Brno Tel. +�� � ��� ��� ��� · Fax +�� � ��� ��� ���
[email protected] · www.sktechnik.cz Fikret Erdogan ve Ort. Koll. Sti. Otakçilar Cad. No. �� · ����� Eyüp-Istanbul Tel. +�� ���-��� �� �� · Fax +�� ���-��� �� ��
[email protected] FIBRO Inc. ��� Harrison Ave. · Rockford, IL ����� P. O. B. ���� · Rockford, IL ����� Tel. +� ���-��� �� �� · Fax +� ���-��� �� ��
[email protected] · www.fibro.com Herrmann & Herrmann Pty. Ltd. ��, Shaft Road · P. O. B. ����� · Knights ���� Tel. +�� �� ��� �� �� · Fax +�� �� ��� �� ��
[email protected] · www.hermstools.com
▶ FIBRO 19
DE
FIBRO GmbH Geschäftsbereich Rundtische Brüggbühlstraße 70 CH-3172 Niederwangen b. Bern Phone +41/31/9810752 Fax +41/31/9810753
[email protected]
CH
FIBRO France SARL Département Plateaux Diviseurs 19/21, rue Jean Lolive F-93170 Bagnolet Phone +33/1/43621880 Fax +33/1/ 48591747
[email protected]
FR
FIBRO Inc. Business Area Rotary Tables 139 Harrison Avenue US-Rockford, IL 61104 Phone +1/815/2291300 Fax +1/815/2291303
[email protected]
US
FIBRO Asia Pte.Ltd. 121 Genting Lane 2nd floor SG-Singapore 349572 Phone +65/68/463303 Fax +65/68/463302
[email protected]
SG
www.fibro.com
Zastoupení v České republice: SK Technik, spol. s r. o. Merhautova 20 CZ - 613 00 Brno Tel.: +420 545 429 511 Fax: +420 545 211 275
[email protected] www.sktechnik.cz
01/2010 © Copyright by FIBRO GmbH Printed in Germany on paper bleached without chlorine
FIBRO GmbH Geschäftsbereich Rundtische Weidachstraße 41-43 D-74189 Weinsberg Phone +49/7134/73-0 Fax +49/7134/73-237
[email protected]
Art.-Nr. 1.4002.00.00.00.11000CZ
Rundtische