STATICKÉ POSOUZENÍ
Projekční ateliér: Projektant:
ENGINEERS CZ s.r.o. Ing. Alexandr Cedrych
Kraj. úřad: Praha
IČO: 24127663
Tel.: +420 252546463
[email protected] IČO: 43082734 Razítko:
Místní úřad: Praha
Investor: Vězeňská služba České republiky Stavba – objekt:
Instalace výtahu do stávající šachty Staré náměstí 3/12, 161 02 Praha 6
Formát: Datum:
23.9.2013
Účel: SP Č.zakázky: Obsah: Statické posouzení
Statické posouzení
Měřítko
1
Obsah statického posouzení 1) Technická zpráva 2) Statické posouzení 3) Závěr 1) Technická zpráva Původní výtah bude nahrazen výtahem s nosností 1400 kg, který je situován do stávající výtahové šachty. Při modernizaci bude nainstalován nový kompletní výtah. Stávající strojovna výtahu nebude využívána, výtahový stroj je umístěný v šachtě.
Použité normy a podklady ČSN EN 1990 - Zásady navrhování konstrukcí ČSN EN 1991-1-1 - Eurokód 1: Zatížení konstrukcí - Část 1-1: Obecná zatížení - Objemové tíhy, vlastní tíha a užitná zatížení pozemních staveb
ČSN EN 1992-1-1 - Eurokód 2: Navrhování betonových konstrukcí - Část 1-1: Obecná pravidla a pravidla pro pozemní stavby
ČSN EN 1993-1-1 - Eurokód 3: Navrhování ocelových konstrukcí - Část 1-1: Obecná pravidla a pravidla ČSN EN ČSN EN
pro pozemní stavby 1996-1-1 - Eurokód 6: Navrhování zděných konstrukcí - Část 1-1: Obecná pravidla pro vyztužené a nevyztužené zděné konstrukce 1997-1 - Eurokód 7: Navrhování geotechnických konstrukcí - Část 1: Obecná pravidla
Stavební část projektu Fotodokumentace objektu Částečná původní dokumentace objektu
Statické posouzení
2
2) Statické posouzení Jsou posouzeny konstrukce, na které působí zatížení od výtahu: – – –
zatížení na dno šachty zatížení ve strojovně zatížení stěn od vodítek
A) Zatížení na dno šachty Od výtahu: Je předpokládáno zatížení osamělou silou cca 120 kN (mimořádná síla dosednutí kabiny nebo protiváhy odpovídající nosnosti výtahu s rezervou). Prohlubeň: Je vypočtena minimální tloušťka desky z prostého betonu a železobetonu (s uvažováním vyztužení síťí 12/150-12/150 (ocel minimálně E-10216). Beton vany je uvažován B250 (odpovídá minimálně betonu C16/20 dle současné normy). Skladby vrstev dna prohlubně budou ověřeny na stavbě. Je provedeno posouzení dolní desky na protlačení a ohyb. Na straně bezpečnosti není uvažováno se spolupůsobením stěn prohlubně. Zatížení v mimořádné kombinaci
R = 120,0 kN
Posouzení dolní desky – mimořádná kombinace: Síla R – prostý beton: Zatěžovací síla (charakteristická) Vek = 120.0 kN Zatěžovací síla (mimořádná) Ved = 120.0 kN Výpočet proveden pro mimořádnou kombinaci, součinitel zatížení = 1 Roznášecí plocha a = 200 mm b = 200 mm Tloušťka desky d = 280 mm Beton desky: C16/20
prostý beton
Posouzení protlačení betonové desky: Kontaktní napětí sigma = 51.6 kPa Návrhová protlačující síla Ved = 72.0 kN (s uvažováním redukce síly od vlivu kontaktního napětí) Kritický obvod u = 3.44 m Umístění zatěžovací síly - vnitřní část Únosnost průřezu Maximální únosnost průřezu Rozhodující únosnost Statické posouzení
Vrdc = 165.2 kN Vrdmax = 583.6 kN Vrd = 165.2 kN 3
Protlačující síla Ved = 72.0 kN < Vrd = 165.2 kN Vyhovuje Posouzení desky v ohybu: Podloží desky: Ulehlý písek Modul reakce podloží: Kk = 80 MN/m3 Maximální moment v desce Mvd = 20.54 kNm Moment únosnosti (prostý beton) Mrd = 20.89 kNm Posouzení desky: Mvd = 20.54 kNm < Mrd = 20.89 MPa Vyhovuje Síla R – železobeton: Zatěžovací síla (charakteristická) Vek = 120.0 kN Zatěžovací síla (mimořádná) Ved = 120.0 kN Výpočet proveden pro mimořádnou kombinaci, součinitel zatížení = 1 Roznášecí plocha a = 200 mm b = 200 mm Tloušťka desky d = 200 mm Beton desky: C16/20 Ocel: 10216 Výztuž desky: 6,66 x D = 12 mm/m Plocha výztuže desky As = 7.53 cm2/m Posouzení protlačení betonové desky: Kontaktní napětí sigma = 118.2 kPa Návrhová protlačující síla Ved = 72.0 kN (s uvažováním redukce síly od vlivu kontaktního napětí) Kritický obvod u = 2.29 m Umístění zatěžovací síly - vnitřní část Únosnost průřezu Maximální únosnost průřezu Rozhodující únosnost
Vrdc = 148.6 kN Vrdmax = 329.3 kN Vrd = 148.6 kN
Protlačující síla Ved = 72.0 kN < Vrd = 148.6 kN Vyhovuje Posouzení desky v ohybu: Podloží desky: Ulehlý písek Modul reakce podloží: Kk = 80 MN/m3 Maximální moment v desce Mvd = 19.76 kNm
Statické posouzení
4
Moment únosnosti (železobeton) Mrd = 21.26 kNm Posouzení desky: Mvd = 19.76 kNm < Mrd = 21.26 MPa Vyhovuje B Zatížení ve strojovně Podlahu strojovny výtahu tvoří železobetonová deska tloušťky 200 mm vetknutá do obvodových konstrukcí. Vyztužení desky není přesně zjištěno. Je uvažováno zatížení silou od montážních háků (zatížení silou R = 40 kN ve středu desky). Je vyčísleno minimální vyztužení desky potřebné pro přenesení sil. Vyztužení desky bude na stavbě ověřeno. Při nižším vyztužení bude provedeno zesílení desky.
Uvedená výztuž musí být v obou směrech. Výztuž odpovídá např. E12 e150 ( 7,53 cm2/m).
Statické posouzení
5
C) Kotvení vodítek Zděné stěny výtahové šachty vyhovují sílám od vodítek. Pro kotvení je nutné volit vhodné chemické kotvy do zdiva s požadovanou únosností.
3) Závěr Betonová vana v prohlubni výtahu vyhovuje pro zatížení silami od výtahu při minimální tloušťce prostého betonu 280 mm. U železobetonu s uvažovanou výztuží 12/150-12/150 vyhovuje tloušťka desky 200 mm. Skladby vrstev dna prohlubně musí být ověřeny na stavbě. Je nutné ověřit vyztužení stropní desky nad šachtou. Vyztužení musí odpovídat podmínkám v bodu B).
Při rekonstrukci není narušena statika objektu.
Statické posouzení
6