CZ
Habermaaß-hra 4145
Ventilátor - stavebnice
Vážení nadějní Inženýři, pomocí této stavebnice si můžete vytvořit svůj vlastní ventilátor a zároveň se seznámíte s velmi důležitým technickým mechanismem, převodovým systémem. V tomto případě rychlostním převodem. Možná si to neuvědomujete, ale rychlostní převodové systémy jsou nedílnou součástí téměř všeho, co používáme. Téměř všechny stroje vyžadují toto zařízení pro své fungování: vozidla, jako jsou auta a kola, stejně jako nástroje, jako jsou vrtačky a hodiny. Jsme si jisti, že byste se rádi seznámili s tím, jak převodový mechanismus funguje, ještě dříve než začnete stavět. Zde je několik základních informací:
2
Distributor ČR: AV distribuce s.r.o. Přátelství 1503/14b, Praha 10
Co je převodový systém a jak funguje? Převodové systémy se skládají z několika mechanických dílů. Když se tyto díly sestaví dohromady, vytvoří mechanismus, který lze použít pro převod pohybu nebo síly. Například, aby bylo možné zvýšit točivý moment (rychlost otáčení), změnit směr otáčení nebo změnit osu rotace. V závislosti na jejich součástech, rozlišujeme různé typy převodových systémů. Jsou to vačkové převody, řetězové převody, šnekové převody, klikové mechanismy a další. Ozubená převodová kola jsou známá již dlouhou dobu. Ozubená kola nebo kola s trny se používala již ve starověkém Egyptě. Byla to dřevěná nebo kamenná kola, do kterých byly vloženy takzvané trny. Tato stará trnová kola byla velmi jednoduchá a méně přesná nežli dnešní ozubená kola, ale zase bylo daleko snadnější je vyrobit. První kolo sezačne otáčet po otočení klikou a tento pohyb se přenáší na ostatní kola soukolí, neboť kola do sebe zapadají. U kol je uvedeno kolikrát se otočí v závislosti na počtu trnů kola vzhledem k počtu otočení kliky. (otočíme-li klikou 1x, otočí se poslední kolo soukoli 3x).
Distributor ČR: AV distribuce s.r.o. Přátelství 1503/14b, Praha 10
3
Vrtule Jeho snadné vysvětlit, jak vrtule a její tři lopatky pracují. Když se vrtule začne otáčet, začnou šikmé plochy lopatek pohybovat vzduchem dopředu nebo dozadu v závislosti na nastavení lopatek a směru otáčení vrtule. Po dokončení stavby to můžete pro zábavu vyzkoušet, postavte před ventilátor svíčku, zapalte ji a zase sfoukněte, aby se vytvořila trocha kouře. Nyní otáčejte klikou ventilátoru a uvidíte, kam se kouř pohybuje. Můžete rovněž pozorovat pohyb plamenu zapálené svíčky. Nikdy to ale nedělejte sami, vždy si vezměte na pomoc někoho dospělého, který vám
4
Distributor ČR: AV distribuce s.r.o. Přátelství 1503/14b, Praha 10
s tím pomůže.
Kotouč Místo vrtule, můžete k ose ventilátoru připojit kotouč na který pomocí sponek můžete připojit jeden ze čtyř dodávaných černobílých kotoučů. Kotouč číslo 1 ukazuje spirálu. Vyzkoušejte co se stane budete-li se upřeně dívat na tento otáčející se disk po dobu 30 vteřin a potom se hned podíváte na svojí dlaň. Kotouč číslo 2 vám zase při pomalém otáčení ukáže kužel. Kotouč číslo 3 se bude při otáčení kolébat tam a zpět. Kotouč číslo 4. Tím musíte otáčet hodně rychle a v závislosti na rychlosti otáčení pak uvidíte různé barvy. Mimochodem, vědci nebyli dosud schopni vysvětlit proč tomu tak je. Samozřejmě si můžete také navrhnout vlastní kotouče. Stačí na to čistý papír nebo čtvrtka. Jako vzor můžete použít originální kotouč. Na disk potom můžete při otáčení kliky malovat různé obrazce, nejlépe pastelkami. Můřete ale použít i barvy a štětec a vytvořit na kotouči různé barevné plochy. Můžete zkrátka svobodně experimentovat a bavit se a popustit
Distributor ČR: AV distribuce s.r.o. Přátelství 1503/14b, Praha 10
5
uzdu své fantazii.
Dřevo Dřevěné části drží v nosné desce za malé kousíčky, aby nemohli vypadnout. Tyto kousky po vytlačení z nosné desky mohou způsobit určité nerovnosti na okrajích dílů, které můžeme snadno vyrovnat pomocí jemného brusného papíru, nebo jemným pilníkem. Jednotlivé dřevěné díly jsou řezány laserovým paprskem, a to je důvod, proč jsou hrany dílů začernalé a lehce jsou cítit po spáleném dřevu.
Místa, která jsou v návodu označena symbolem svíčky, by měla být namazána svíčkovým voskem. To usnadní pohyb jednotlivých pohyblivých částí ventilátoru. Pozor, nesmíte voskem namazat místa, která je třeba slepit!
Návod na sestavení (originál návodu str. 37) Slepené díly musí po určitou dobu schnout. U jednotlivých dílu byste měli počkat alespoň 20minut, než s nimi budete pokračovat v práci. Lepidlo poteče z láhve rychleji, budete-li ji pokládat na bok nebo stavět obráceně dnem vzhůru. Láhev s lepidlem vždy důkladně uzavírejte, aby vám lepidlo nevyschlo. Aby bylo možné umístit disky na čepu kola přesně otvory nad sebe, Nasuňte je při lepení na tyč. Ale pozor, ujistěte se, že se k tyči nemohou přilepit a včas tyč vyjměte.
6
Distributor ČR: AV distribuce s.r.o. Přátelství 1503/14b, Praha 10
Pokud se ventilátor netočí, protože základní deska je lehce nakřivo, stačí použít tři podložky místo čtyř. Experimentujte, dokud nenajdete tu nejlepší pozici.
Pokud se ventilátor stále zadrhává, pak opatrně zkontrolujte jednotlivé trny ozubených kol. Stačí jeden křivý trn a může narušit lehký chod soukolí. Označte si vadný trn a velmi opatrně opravte jeho polohu. Nebo použijte trochu vosku, abyste odstranili tření. Mimochodem závady v chodu se spíše projevují při pomalém chodu, než když se ventilátor točí rychle. A je hotovo! Nyní můžete začít kutit a experimentovat! Přeložený text ze strany 41 originálu návodu: Pozor! Vrchní díl zatím nelepte, poslouží vám nyní pouze k přidržení stojek ve správné poloze. Přeložený text ze strany 42 originálu návodu: Tip! Pokud jste levák, můžete kliku připevnit na druhou stranu.
Distributor ČR: AV distribuce s.r.o. Přátelství 1503/14b, Praha 10
7