1. EIGRP – konfig dasar 12.12.12.1/24
============ R1 ============ en conf t hostname R1
12.12.12.2/24
ork er
int s0/0 ip addr 12.12.12.1 255.255.255.0 no sh int lo0 ip addr 1.1.1.1 255.255.255.255 no sh router eigrp 10 net 12.12.12.1 0.0.0.0 net 1.1.1.1 0.0.0.0 no au
ID-N etw
============ R2 ============ en conf t hostname R2
int s0/0 ip addr 12.12.12.2 255.255.255.0 no sh INT fa0/0 ip addr 23.23.23.2 255.255.255.0 no sh int lo0 ip addr 2.2.2.2 255.255.255.255 no sh router eigrp 10 net 12.12.12.2 0.0.0.0 net 2.2.2.2 0.0.0.0 net 23.23.23.2 0.0.0.0 no au ============
23.23.23.3/24
s
23.23.23.2/24
R3 ============ en conf t hostname R1 int fa0/0 ip addr 23.23.23.3 255.255.255.0 no sh int lo0 ip addr 3.3.3.3 255.255.255.255 no sh
s
router eigrp 10 net 23.23.23.3 0.0.0.0 net 3.3.3.3 0.0.0.0 no au
ork er
================================================================ cek routing tabel dan tes ping R1#sh ip route C D
ID-N etw
D
1.0.0.0/32 is subnetted, 1 subnets 1.1.1.1 is directly connected, Loopback0 2.0.0.0/32 is subnetted, 1 subnets 2.2.2.2 [90/2297856] via 12.12.12.2, 00:11:43, Serial0/0 3.0.0.0/32 is subnetted, 1 subnets 3.3.3.3 [90/2323456] via 12.12.12.2, 00:11:35, Serial0/0 23.0.0.0/24 is subnetted, 1 subnets 23.23.23.0 [90/2195456] via 12.12.12.2, 00:11:42, Serial0/0 12.0.0.0/24 is subnetted, 1 subnets 12.12.12.0 is directly connected, Serial0/0
D C
R1#ping 1.1.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/8 ms R1#ping 2.2.2.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2.2.2.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/76/164 ms R1#ping 3.3.3.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 3.3.3.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 120/167/252 ms
2. EIGRP – Filtering Route Bila diinginkan IP Loopbak2 tidak boleh terdapat dalam routing Tabel Router R3 R1(config)#access-list 1 deny 2.2.2.2 R1(config)#access-list 1 permit any R1(config)#router eigrp 10 R1(config-router)#distribute-list 1 in s0/0 ================================================================ Kemudian cek di routing tabelnya dan pastikan IP 2.2.2.2 sudah tidak lagi terdapat dalam routing tabelnya
s
R1#sh ip route
ork er
1.0.0.0/32 is subnetted, 1 subnets 1.1.1.1 is directly connected, Loopback0 3.0.0.0/32 is subnetted, 1 subnets D 3.3.3.3 [90/2323456] via 12.12.12.2, 00:28:23, Serial0/0 23.0.0.0/24 is subnetted, 1 subnets D 23.23.23.0 [90/2195456] via 12.12.12.2, 00:28:29, Serial0/0 12.0.0.0/24 is subnetted, 1 subnets C 12.12.12.0 is directly connected, Serial0/0 ================================================================ Selain dikonfigurasikan di Router R1, bias juga dikonfigurasikan di Router R2 namun dengan direction OUT. C
ID-N etw
Hapus dulu konfigurasi di Router R1 R1(config)#router eigrp 10 R1(config-router)#no distribute-list 1 in s0/0 Cek routing tabelnya
R1#sh ip route 1.0.0.0/32 is subnetted, 1 subnets C 1.1.1.1 is directly connected, Loopback0 2.0.0.0/32 is subnetted, 1 subnets D 2.2.2.2 [90/2297856] via 12.12.12.2, 00:28:24, Serial0/0 3.0.0.0/32 is subnetted, 1 subnets D 3.3.3.3 [90/2323456] via 12.12.12.2, 00:28:16, Serial0/0 23.0.0.0/24 is subnetted, 1 subnets D 23.23.23.0 [90/2195456] via 12.12.12.2, 00:28:22, Serial0/0 12.0.0.0/24 is subnetted, 1 subnets C 12.12.12.0 is directly connected, Serial0/0 ========================================================================== Kmudian dilanjutkan konfigurasi di router R2 R2(config)#access-list 1 deny 2.2.2.2 R2(config)#access-list 1 permit any R2(config)#router eigrp 10 R2(config-router)#distribute-list 1 out s0/0 Cek lagi routing tabelnya
R1#sh ip route 1.0.0.0/32 is subnetted, 1 subnets C 1.1.1.1 is directly connected, Loopback0 3.0.0.0/32 is subnetted, 1 subnets D 3.3.3.3 [90/2323456] via 12.12.12.2, 00:32:36, Serial0/0 23.0.0.0/24 is subnetted, 1 subnets D 23.23.23.0 [90/2195456] via 12.12.12.2, 00:32:42, Serial0/0 12.0.0.0/24 is subnetted, 1 subnets C 12.12.12.0 is directly connected, Serial0/0
ID-N etw
ork er
s
Dan hasilnya IP 2.2.2.2 sudah tidak lagi terdapat dalam routing tabelnya.
3. EIGRP – Redistributing Routes Kalau sebelumnya kita mengadvertise sebuah network melalui perintah network pada EIGRP, maka selanjutnya kita akan menggunakan redistribute route 3.1 Redistribute Static Buat interface loopback di Router R1 R1(config)#int lo1 R1(config-if)#ip address 100.100.100.1 255.255.255.255
ork er
Redistribute ke EIGRP R1(config)#router eigrp 10 R1(config-router)#redistribute static
s
Buat routing static di Router R2 R2(config)#ip route 100.100.100.1 255.255.255.255 12.12.12.1
Cek routing tabelnya di Router R3
ID-N etw
R3#sh ip route 1.0.0.0/32 is subnetted, 1 subnets D 1.1.1.1 [90/2323456] via 23.23.23.2, 00:09:14, FastEthernet0/0 2.0.0.0/32 is subnetted, 1 subnets D 2.2.2.2 [90/409600] via 23.23.23.2, 00:28:08, FastEthernet0/0 100.0.0.0/32 is subnetted, 1 subnets D EX 100.100.100.1 [170/2195456] via 23.23.23.2, 00:00:15, FastEthernet0/0 3.0.0.0/32 is subnetted, 1 subnets C 3.3.3.3 is directly connected, Loopback0 23.0.0.0/24 is subnetted, 1 subnets C 23.23.23.0 is directly connected, FastEthernet0/0 12.0.0.0/24 is subnetted, 1 subnets D 12.12.12.0 [90/2195456] via 23.23.23.2, 00:40:23, FastEthernet0/0
à EX - EIGRP external,
R3#ping 100.100.100.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 100.100.100.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 128/170/220 ms
3.2 Redistribute RIP 1. Buat interface loopback di Router R1 R1(config)#int lo2 R1(config-if)#ip address 200.200.200.1 255.255.255.255 2. Advertise kedalam RIP
R1(config-if)#router rip R1(config-router)#network 200.200.200.0 3. Redistribute kedalam EIGRP R1(config)#router eigrp 10 R1(config-router)#redistribute rip metric 1 1 1 1 1
ork er
s
4. Pengecekan R1(config-router)#do sh ip pro Routing Protocol is "eigrp 10" Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Default networks flagged in outgoing updates Default networks accepted from incoming updates EIGRP metric weight K1=1, K2=0, K3=1, K4=0, K5=0 EIGRP maximum hopcount 100 EIGRP maximum metric variance 1 Redistributing: eigrp 10, rip EIGRP NSF-aware route hold timer is 240s Automatic network summarization is not in effect Maximum path: 4 Routing for Networks: 1.1.1.1/32 12.12.12.1/32 Routing Information Sources: Gateway Distance Last Update (this router) 90 02:22:47 12.12.12.2 90 00:12:51 Distance: internal 90 external 170
ID-N etw
R3#sh ip route eigrp 200.200.200.0/32 is subnetted, 1 subnets D EX 200.200.200.1 [170/2560537856] via 23.23.23.2, 00:13:10, FastEthernet0/0 1.0.0.0/32 is subnetted, 1 subnets D 1.1.1.1 [90/2323456] via 23.23.23.2, 00:26:09, FastEthernet0/0 2.0.0.0/32 is subnetted, 1 subnets D 2.2.2.2 [90/409600] via 23.23.23.2, 01:57:15, FastEthernet0/0 100.0.0.0/32 is subnetted, 1 subnets D EX 100.100.100.1 [170/2195456] via 23.23.23.2, 01:29:23, FastEthernet0/0 12.0.0.0/24 is subnetted, 1 subnets D 12.12.12.0 [90/2195456] via 23.23.23.2, 02:09:30, FastEthernet0/0 R3#ping 200.200.200.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 200.200.200.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 180/205/244 ms
3.3 Redistribute OSPF
1. Buat interface loopback di Router R1 R1(config-router)#int lo3 R1(config-if)#ip address 30.30.30.1 255.255.255.255 2. Advertise ke dalam OSPF R1(config-if)#router ospf 1 R1(config-router)#net 30.30.30.1 0.0.0.0 area 0 3. Redistribute kedalam EIGRP R1(config-router)#router eigrp 10 R1(config-router)#redistribute ospf 1 metric 1 1 1 1 1 4. Pengecekan
s
R1(config-router)#do sh ip pro | i Redistrib Redistributing: eigrp 10, rip, ospf 1
ID-N etw
ork er
R3#sh ip route eigrp 200.200.200.0/32 is subnetted, 1 subnets D EX 200.200.200.1 [170/2560537856] via 23.23.23.2, 00:15:56, FastEthernet0/0 1.0.0.0/32 is subnetted, 1 subnets D 1.1.1.1 [90/2323456] via 23.23.23.2, 00:28:54, FastEthernet0/0 2.0.0.0/32 is subnetted, 1 subnets D 2.2.2.2 [90/409600] via 23.23.23.2, 02:00:01, FastEthernet0/0 100.0.0.0/32 is subnetted, 1 subnets D EX 100.100.100.1 [170/2195456] via 23.23.23.2, 01:32:08, FastEthernet0/0 12.0.0.0/24 is subnetted, 1 subnets D 12.12.12.0 [90/2195456] via 23.23.23.2, 02:12:16, FastEthernet0/0 30.0.0.0/32 is subnetted, 1 subnets D EX 30.30.30.1 [170/2560537856] via 23.23.23.2, 00:00:08, FastEthernet0/0
R3#ping 30.30.30.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 30.30.30.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 48/163/244 ms
4. EIGRP – Authentication R1(config)#key chain EIGRP R1(config-keychain)#key 1 R1(config-keychain-key)#key-string CISCO R1(config-keychain-key)#int S0/0 R1(config-if)#ip authentication key-chain eigrp 10 EIGRP R1(config-if)#ip authentication mode eigrp 10 md5
ork er
R2(config)#key chain EIGRP R2(config-keychain)#key 1 R2(config-keychain-key)#key-string CISCO
s
================================================================
R2(config-keychain-key)#INT S0/0 R2(config-if)#ip authentication mode eigrp 10 md5 R2(config-if)#ip authentication key-chain eigrp 10 EIGRP
ID-N etw
================================================================ R1#DEBUg EIGrp PACkets EIGRP Packets debugging is on (UPDATE, REQUEST, QUERY, REPLY, HELLO, IPXSAP, PROBE, ACK, STUB, SIAQUERY, SIAREPLY) *Mar 1 03:46:42.303: EIGRP: received packet with MD5 authentication, key id = 1 *Mar 1 03:46:42.307: EIGRP: Received HELLO on Serial0/0 nbr 12.12.12.2 *Mar 1 03:46:42.311: AS 10, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/0 *Mar 1 03:46:45.467: EIGRP: Sending HELLO on Loopback0 *Mar 1 03:46:45.471: AS 10, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 *Mar 1 03:46:45.479: EIGRP: Received HELLO on Loopback0 nbr 1.1.1.1 *Mar 1 03:46:45.483: AS 10, Flags 0x0, Seq 0/0 idbQ 0/0 ================================================================ R1#sh ip eigrp neighbors IP-EIGRP neighbors for process 10 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 12.12.12.2 Se0/0 11 00:12:14 232 1392 0 77
5. EIGRP – Timer Terdapat dua EIGRP timer, yakni • Hello interval (default : 5 seconds) • Hold-time (default : 15 seconds) R1#sh ip eigrp neighbors IP-EIGRP neighbors for process 10 H Address Interface Hold (sec) 0 12.12.12.2 Se0/0 11
Uptime SRTT RTO Q Seq (ms) Cnt Num 00:12:14 232 1392 0 77
s
Nilai hold-time yang ditampilkan sh ip eigrp neighbors adalah menghitung mundur dari 15 sec
ID-N etw
ork er
Berikut untuk melakukan perubahan konfigurasinya, hello interval 3 detik dan hold-time 9 detik (tiga kalinya) R3(config)#int fa0/0 R3(config-if)#ip hello-interval eigrp 10 3 R3(config-if)#ip hold-time eigrp 10 9
6. EIGRP – Route Summarization
Advertise kedalam EIGRP
ork er
R3(config)#int lo1 R3(config-if)#ip address 10.0.0.1 255.255.255.255 R3(config-if)#int lo2 R3(config-if)#ip address 10.0.0.2 255.255.255.255 R3(config-if)#int lo3 R3(config-if)#ip address 10.0.0.3 255.255.255.255 R3(config-if)#int lo4 R3(config-if)#ip address 10.0.0.4 255.255.255.255 R3(config-if)#int lo5 R3(config-if)#ip address 10.0.0.5 255.255.255.255 R3(config-if)#int lo6 R3(config-if)#ip address 10.0.0.6 255.255.255.255 R3(config-if)#int lo7 R3(config-if)#ip address 10.0.0.7 255.255.255.255
s
Buat ip yang akan di summarize dulu
R3(config-if)#router eigrp 10 R3(config-router)#net 10.0.0.1 0.0.0.0 R3(config-router)#net 10.0.0.2 0.0.0.0 R3(config-router)#net 10.0.0.3 0.0.0.0 R3(config-router)#net 10.0.0.4 0.0.0.0 R3(config-router)#net 10.0.0.5 0.0.0.0 R3(config-router)#net 10.0.0.6 0.0.0.0 R3(config-router)#net 10.0.0.7 0.0.0.0
ID-N etw
================================================================ Cek di router R1
R1#sh ip route eigrp 3.0.0.0/32 is subnetted, 1 subnets D 3.3.3.3 [90/2323456] via 12.12.12.2, 00:07:54, Serial0/0 23.0.0.0/24 is subnetted, 1 subnets D 23.23.23.0 [90/2195456] via 12.12.12.2, 00:58:05, Serial0/0 10.0.0.0/32 is subnetted, 7 subnets D 10.0.0.2 [90/2323456] via 12.12.12.2, 00:01:27, Serial0/0 D 10.0.0.3 [90/2323456] via 12.12.12.2, 00:01:23, Serial0/0 D 10.0.0.1 [90/2323456] via 12.12.12.2, 00:01:32, Serial0/0 D 10.0.0.6 [90/2323456] via 12.12.12.2, 00:01:11, Serial0/0 D 10.0.0.7 [90/2323456] via 12.12.12.2, 00:00:35, Serial0/0 D 10.0.0.4 [90/2323456] via 12.12.12.2, 00:01:21, Serial0/0 D 10.0.0.5 [90/2323456] via 12.12.12.2, 00:01:18, Serial0/0
================================================================ Konfigurasikan summarization di router R3 R3(config-if)#ROUTER EIGRP 10 R3(config-if)#ip summary-address eigrp 10 10.0.0.0 255.255.255.248 R3(config-if)# *Mar 1 04:54:10.986: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 10: Neighbor 23.23.23.2 (FastEthernet0/0) is resync: summary configured
================================================================ Cek lagi di router R1 R1#sh ip route eigrp 3.0.0.0/32 is subnetted, 1 subnets D 3.3.3.3 [90/2323456] via 12.12.12.2, 00:16:46, Serial0/0 23.0.0.0/24 is subnetted, 1 subnets D 23.23.23.0 [90/2195456] via 12.12.12.2, 01:06:57, Serial0/0 10.0.0.0/29 is subnetted, 1 subnets D 10.0.0.0 [90/2323456] via 12.12.12.2, 00:00:07, Serial0/0 12.0.0.0/24 is subnetted, 1 subnets
ork er
s
R1#ping 10.0.0.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.0.0.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 112/166/240 ms R1#ping 10.0.0.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.0.0.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 80/132/176 ms
ID-N etw
R1#ping 10.0.0.7 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.0.0.7, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 116/177/268 ms
7. EIGRP – Unicast Update 12.12.12.1/24 23.23.23.2/24 12.12.12.2/24
23.23.23.3/24
ork er
s
R1(config-if)#do deb ip packet de IP packet debugging is on (detailed) *Mar 1 00:48:02.723: IP: s=12.12.12.2 (Serial0/0), d=224.0.0.10, len 60, rcvd 2, proto=88 *Mar 1 00:48:02.747: IP: s=12.12.12.1 (local), d=224.0.0.10 (Serial0/0), len 60, sending broad/multicast, proto=88 *Mar 1 00:48:02.763: IP: s=12.12.12.1 (local), d=12.12.12.2 (Serial0/0), len 40, sending, proto=88 *Mar 1 00:48:02.963: IP: s=12.12.12.2 (Serial0/0), d=224.0.0.10, len 60, rcvd 2, proto=88 *Mar 1 00:48:02.971: IP: tableid=0, s=12.12.12.2 (Serial0/0), d=12.12.12.1 (Serial0/0), routed via RIB *Mar 1 00:48:02.975: IP: s=12.12.12.2 (Serial0/0), d=12.12.12.1 (Serial0/0), len 40, rcvd 3, proto=88 *Mar 1 00:48:02.995: IP: s=12.12.12.1 (local), d=12.12.12.2 (Serial0/0), len 40, sending, proto=88 ================================================================ Untuk merubah menjadi unicast (Link R1-R2) R1(config-if)#router eigrp 10 R1(config-router)#neighbor 12.12.12.2 s0/0
ID-N etw
R2(config-if)#router eigrp 10 R2(config-router)#neighbor 12.12.12.1 s0/0
R1#debug ip packet det IP packet debugging is on (detailed) *Mar 1 00:55:06.163: IP: s=12.12.12.1 (local), d=12.12.12.2 (Serial0/0), len 60, sending, proto=88 *Mar 1 00:55:10.747: IP: s=12.12.12.1 (local), d=12.12.12.2 (Serial0/0), len 60, sending, proto=88 *Mar 1 00:55:10.867: IP: tableid=0, s=12.12.12.2 (Serial0/0), d=12.12.12.1 (Serial0/0), routed via RIB *Mar 1 00:55:10.871: IP: s=12.12.12.2 (Serial0/0), d=12.12.12.1 (Serial0/0), len 60, rcvd 3, proto=88 *Mar 1 00:55:10.879: IP: tableid=0, s=12.12.12.2 (Serial0/0), d=12.12.12.1 (Serial0/0), routed via RIB *Mar 1 00:55:10.879: IP: s=12.12.12.2 (Serial0/0), d=12.12.12.1 (Serial0/0), len 40, rcvd 3, proto=88 *Mar 1 00:55:10.899: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 10: Neighbor 12.12.12.2 (Serial0/0) is up: new adjacency *Mar 1 00:55:10.907: IP: s=12.12.12.1 (local), d=12.12.12.2 (Serial0/0), len 60, sending, proto=88 *Mar 1 00:55:10.927: IP: s=12.12.12.1 (local), d=12.12.12.2 (Serial0/0), len 40, sending, proto=88 *Mar 1 00:55:11.147: IP: tableid=0, s=12.12.12.2 (Serial0/0), d=12.12.12.1 (Serial0/0), routed via RIB *Mar 1 00:55:11.151: IP: s=12.12.12.2 (Serial0/0), d=12.12.12.1 (Serial0/0), len 68, rcvd 3, proto=88 *Mar 1 00:55:11.171: IP: s=12.12.12.1 (local), d=12.12.12.2 (Serial0/0), len 40, sending, proto=88
8. EIGRP – Traffic Engineering 12.12.12.1/24 12.12.12.2/24 13.13.13.1/24
23.23.23.3/24
ork er
13.13.13.3/24
s
23.23.23.2/24
Kondisi normal tentunya trafik dari router R1 menuju Loopback R3 adalah langsung menuju router R3 karena perhitungan bandwitdhnya. nah bila diinginkan trafik melewati router R2 dulu maka parameter metric bisa kita rubah agar memenuhi hal tersebut, salah satunya adalah Delay. ================================================================ Kondisi awal.......
ID-N etw
R1(config-router)#do sh ip route 3.3.3.3 Routing entry for 3.3.3.3/32 Known via "eigrp 10", distance 90, metric 409600, type internal Redistributing via eigrp 10 Last update from 13.13.13.3 on FastEthernet0/0, 00:00:50 ago Routing Descriptor Blocks: * 13.13.13.3, from 13.13.13.3, 00:00:50 ago, via FastEthernet0/0 Route metric is 409600, traffic share count is 1 Total delay is 6000 microseconds, minimum bandwidth is 10000 Kbit Reliability 255/255, minimum MTU 1500 bytes Loading 1/255, Hops 1
R1(config-router)#do ping 3.3.3.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 3.3.3.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 36/133/192 ms R1(config-router)#do trace 3.3.3.3 Type escape sequence to abort. Tracing the route to 3.3.3.3 1 13.13.13.3 180 msec 120 msec *
ork er
12.12.12.2 (Serial0/0), from 12.12.12.2, Send flag is 0x0 Composite metric is (2323456/409600), Route is Internal Vector metric: Minimum bandwidth is 1544 Kbit Total delay is 26000 microseconds Reliability is 255/255 Load is 1/255 Minimum MTU is 1500 Hop count is 2
s
R1(config-router)#do sh ip eigrp top 3.3.3.3 255.255.255.255 IP-EIGRP (AS 10): Topology entry for 3.3.3.3/32 State is Passive, Query origin flag is 1, 1 Successor(s), FD is 409600 Routing Descriptor Blocks: 13.13.13.3 (FastEthernet0/0), from 13.13.13.3, Send flag is 0x0 Composite metric is (409600/128256), Route is Internal Vector metric: Minimum bandwidth is 10000 Kbit Total delay is 6000 microseconds Reliability is 255/255 Load is 1/255 Minimum MTU is 1500 Hop count is 1
================================================================ Manipulasi nilai metric dengan merubah delay
ID-N etw
R1(config-if)#delay 100000 R1(config-if)#do clear ip eigrp ne *Mar 1 00:13:55.431: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 10: Neighbor 12.12.12.2 (Serial0/0) is down: manually cleared *Mar 1 00:13:55.455: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 10: Neighbor 13.13.13.3 (FastEthernet0/0) is down: manually cleared *Mar 1 00:13:55.791: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 10: Neighbor 13.13.13.3 (FastEthernet0/0) is up: new adjacency *Mar 1 00:13:58.527: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 10: Neighbor 12.12.12.2 (Serial0/0) is up: new adjacency R1(config-if)#do sh ip eigrp top 3.3.3.3 255.255.255.255 IP-EIGRP (AS 10): Topology entry for 3.3.3.3/32 State is Passive, Query origin flag is 1, 1 Successor(s), FD is 2323456 Routing Descriptor Blocks: 12.12.12.2 (Serial0/0), from 12.12.12.2, Send flag is 0x0 Composite metric is (2323456/409600), Route is Internal Vector metric: Minimum bandwidth is 1544 Kbit Total delay is 26000 microseconds Reliability is 255/255 Load is 1/255 Minimum MTU is 1500 Hop count is 2
13.13.13.3 (FastEthernet0/0), from 13.13.13.3, Send flag is 0x0 Composite metric is (25984000/128256), Route is Internal Vector metric: Minimum bandwidth is 10000 Kbit Total delay is 1005000 microseconds Reliability is 255/255 Load is 1/255 Minimum MTU is 1500 Hop count is 1
ork er
s
R1(config-if)#do sh ip route 3.3.3.3 Routing entry for 3.3.3.3/32 Known via "eigrp 10", distance 90, metric 2323456, type internal Redistributing via eigrp 10 Last update from 12.12.12.2 on Serial0/0, 00:02:46 ago Routing Descriptor Blocks: * 12.12.12.2, from 12.12.12.2, 00:02:46 ago, via Serial0/0 Route metric is 2323456, traffic share count is 1 Total delay is 26000 microseconds, minimum bandwidth is 1544 Kbit Reliability 255/255, minimum MTU 1500 bytes Loading 1/255, Hops 2
R1(config-if)#do ping 3.3.3.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 3.3.3.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 88/163/252 ms
ID-N etw
R1(config-if)#do trace 3.3.3.3 Type escape sequence to abort. Tracing the route to 3.3.3.3
1 12.12.12.2 68 msec 52 msec 132 msec 2 23.23.23.3 176 msec 172 msec * R1(config-if)#
Yup sudah pindah jalurnya lewat R2 dulu baru ke R3…..
========================================================================== Selain nilai Delay, bisa juga merubah nilai bandwidthnya, misalkan bandwidth int fa0/0 nya diset 1Mbps saja, shingga lebih rendah dbanding serialnya. R1(config)#int fa0/0 R1(config-if)#no delay 100000
R1(config-if)#bandwidth 1000 R1(config-if)#do clear ip eigrp ne R1(config-if)#do sh ip eigr top 3.3.3.3 255.255.255.255 IP-EIGRP (AS 10): Topology entry for 3.3.3.3/32 State is Passive, Query origin flag is 1, 1 Successor(s), FD is 921600 Routing Descriptor Blocks: 12.12.12.2 (Serial0/0), from 12.12.12.2, Send flag is 0x0 Composite metric is (921600/409600), Route is Internal Vector metric:
Minimum bandwidth is 10000 Kbit Total delay is 26000 microseconds Reliability is 255/255 Load is 1/255 Minimum MTU is 1500 Hop count is 2
ork er
R1(config-if)#do sh ip route 3.0.0.0/32 is subnetted, 1 subnets D 3.3.3.3 [90/921600] via 12.12.12.2, 00:00:14, Serial0/0
s
13.13.13.3 (FastEthernet0/0), from 13.13.13.3, Send flag is 0x0 Composite metric is (2713600/128256), Route is Internal Vector metric: Minimum bandwidth is 1000 Kbit Total delay is 6000 microseconds Reliability is 255/255 Load is 1/255 Minimum MTU is 1500 Hop count is 1
R1(config-if)#do ping 3.3.3.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 3.3.3.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 72/109/128 ms R1(config-if)#do trac 3.3.3.3 Type escape sequence to abort. Tracing the route to 3.3.3.3
ID-N etw
1 12.12.12.2 92 msec 80 msec 88 msec 2 23.23.23.3 120 msec 168 msec * R1(config-if)#
9. EIGRP Filtering– Standard ACL 12.12.12.1/24 23.23.23.2/24 12.12.12.2/24
23.23.23.3/24
ork er
R1(config-router)#int lo1 R1(config-if)#ip address 10.10.10.1 255.255.255.255 R1(config-if)#int lo2 R1(config-if)#ip address 10.10.10.2 255.255.255.255 R1(config-if)#int lo3 R1(config-if)#ip address 10.10.10.3 255.255.255.255 R1(config-if)#int lo4 R1(config-if)#ip address 10.10.10.4 255.255.255.255 R1(config-if)#int lo5 R1(config-if)#ip address 10.10.10.5 255.255.255.255 R1(config-if)#int lo6 R1(config-if)#ip address 10.10.10.6 255.255.255.255
s
Buat IP Loopback dulu utk diadvertise ke dalam EIGRP dan kemudian difilter misal IP Genap dan Ganjil
ID-N etw
R1(config-if)#router eigrp 10 R1(config-router)#net 10.10.10.1 0.0.0.0 R1(config-router)#net 10.10.10.2 0.0.0.0 R1(config-router)#net 10.10.10.3 0.0.0.0 R1(config-router)#net 10.10.10.4 0.0.0.0 R1(config-router)#net 10.10.10.5 0.0.0.0 R1(config-router)#net 10.10.10.6 0.0.0.0
========================================================================== Cek di R3 R3(config-router)#do sh ip rou 1.0.0.0/32 is subnetted, 1 subnets D 1.1.1.1 [90/2323456] via 23.23.23.2, 00:03:15, FastEthernet0/0 2.0.0.0/32 is subnetted, 1 subnets D 2.2.2.2 [90/409600] via 23.23.23.2, 00:03:15, FastEthernet0/0 3.0.0.0/32 is subnetted, 1 subnets C 3.3.3.3 is directly connected, Loopback0 23.0.0.0/24 is subnetted, 1 subnets C 23.23.23.0 is directly connected, FastEthernet0/0 10.0.0.0/32 is subnetted, 6 subnets D 10.10.10.2 [90/2323456] via 23.23.23.2, 00:00:14, FastEthernet0/0 D 10.10.10.3 [90/2323456] via 23.23.23.2, 00:00:12, FastEthernet0/0 D 10.10.10.1 [90/2323456] via 23.23.23.2, 00:00:17, FastEthernet0/0 D 10.10.10.6 [90/2323456] via 23.23.23.2, 00:00:04, FastEthernet0/0 D 10.10.10.4 [90/2323456] via 23.23.23.2, 00:00:11, FastEthernet0/0 D 10.10.10.5 [90/2323456] via 23.23.23.2, 00:00:08, FastEthernet0/0 12.0.0.0/24 is subnetted, 1 subnets D 12.12.12.0 [90/2195456] via 23.23.23.2, 00:03:17, FastEthernet0/0
Dan filtering dimulai …… yang genap dulu R3(config)#access-list 1 permit 0.0.0.0 255.255.255.254 R3(config)#router eigrp 10 R3(config-router)#distribute-list 1 in fa0/0 *Mar 1 00:41:16.867: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 10: Neighbor 23.23.23.2 (FastEthernet0/0) is resync: route configuration changed
Sekarang yang ganjil…
ork er
s
R3(config-router)#do sh ip rou 2.0.0.0/32 is subnetted, 1 subnets D 2.2.2.2 [90/409600] via 23.23.23.2, 00:15:27, FastEthernet0/0 3.0.0.0/32 is subnetted, 1 subnets C 3.3.3.3 is directly connected, Loopback0 23.0.0.0/24 is subnetted, 1 subnets C 23.23.23.0 is directly connected, FastEthernet0/0 10.0.0.0/32 is subnetted, 3 subnets D 10.10.10.2 [90/2323456] via 23.23.23.2, 00:12:26, FastEthernet0/0 D 10.10.10.6 [90/2323456] via 23.23.23.2, 00:12:15, FastEthernet0/0 D 10.10.10.4 [90/2323456] via 23.23.23.2, 00:12:21, FastEthernet0/0 12.0.0.0/24 is subnetted, 1 subnets D 12.12.12.0 [90/2195456] via 23.23.23.2, 00:15:27, FastEthernet0/0
R3(config)#no access-list 1 permit 0.0.0.0 255.255.255.254 R3(config)#access-list 1 permit 0.0.0.1 255.255.255.254 Tunggu sebentar dan….
ID-N etw
R3(config)#do sh ip rou 1.0.0.0/32 is subnetted, 1 subnets D 1.1.1.1 [90/2323456] via 23.23.23.2, 00:00:04, FastEthernet0/0 3.0.0.0/32 is subnetted, 1 subnets C 3.3.3.3 is directly connected, Loopback0 23.0.0.0/24 is subnetted, 1 subnets C 23.23.23.0 is directly connected, FastEthernet0/0 10.0.0.0/32 is subnetted, 3 subnets D 10.10.10.3 [90/2323456] via 23.23.23.2, 00:00:04, FastEthernet0/0 D 10.10.10.1 [90/2323456] via 23.23.23.2, 00:00:04, FastEthernet0/0 D 10.10.10.5 [90/2323456] via 23.23.23.2, 00:00:04, FastEthernet0/0 R3(config)#
10. EIGRP Filtering– AD 12.12.12.1/24 23.23.23.2/24 12.12.12.2/24
23.23.23.3/24
Diinginkan IP Loopback R1 tidak terdapat dalam routing tabel R3
ork er
s
Kondisi awal : R3(config)#do sh ip rou 1.0.0.0/32 is subnetted, 1 subnets D 1.1.1.1 [90/2323456] via 23.23.23.2, 00:08:50, FastEthernet0/0 3.0.0.0/32 is subnetted, 1 subnets C 3.3.3.3 is directly connected, Loopback0 23.0.0.0/24 is subnetted, 1 subnets C 23.23.23.0 is directly connected, FastEthernet0/0 10.0.0.0/32 is subnetted, 3 subnets D 10.10.10.3 [90/2323456] via 23.23.23.2, 00:08:50, FastEthernet0/0 D 10.10.10.1 [90/2323456] via 23.23.23.2, 00:08:50, FastEthernet0/0 D 10.10.10.5 [90/2323456] via 23.23.23.2, 00:08:50, FastEthernet0/0 Konfigurasikan nilai AD yg paling besar yakni 255 R3(config)#access-list 2 permit 1.1.1.1
ID-N etw
R3(config)#router eigrp 10 R3(config-router)#distance 255 0.0.0.0 255.255.255.255 2
Cek lagi R3#sh ip rou 3.0.0.0/32 is subnetted, 1 subnets C 3.3.3.3 is directly connected, Loopback0 23.0.0.0/24 is subnetted, 1 subnets C 23.23.23.0 is directly connected, FastEthernet0/0 10.0.0.0/32 is subnetted, 3 subnets D 10.10.10.3 [90/2323456] via 23.23.23.2, 00:00:02, FastEthernet0/0 D 10.10.10.1 [90/2323456] via 23.23.23.2, 00:00:02, FastEthernet0/0 D 10.10.10.5 [90/2323456] via 23.23.23.2, 00:00:02, FastEthernet0/0 Yup ip loopback R1 (1.1.1.1) sudah tidak terdapat lagi dalam routing tabel Router R3
R3(config)#do sh ip rou 1.1.1.1 % Network not in table R3(config)#do ping 1.1.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds: ..... Success rate is 0 percent (0/5)
11. EIGRP Traffic Engineering – Offset List 12.12.12.1/24 12.12.12.2/24 13.13.13.1/24
23.23.23.3/24
ork er
13.13.13.3/24
s
23.23.23.2/24
Diinginkan trafik dari R1 menuju Loopback R3 dilewatkan ke R2 terlebih dahulu. Kondisi awal
ID-N etw
R1(config-router)#do sh ip rou 1.0.0.0/32 is subnetted, 1 subnets C 1.1.1.1 is directly connected, Loopback0 2.0.0.0/32 is subnetted, 1 subnets D 2.2.2.2 [90/435200] via 13.13.13.3, 00:19:01, FastEthernet0/0 3.0.0.0/32 is subnetted, 1 subnets D 3.3.3.3 [90/409600] via 13.13.13.3, 00:04:34, FastEthernet0/0 (à langsung ke R3) 23.0.0.0/24 is subnetted, 1 subnets D 23.23.23.0 [90/307200] via 13.13.13.3, 00:19:01, FastEthernet0/0 12.0.0.0/24 is subnetted, 1 subnets C 12.12.12.0 is directly connected, Serial0/0 13.0.0.0/24 is subnetted, 1 subnets C 13.13.13.0 is directly connected, FastEthernet0/0 R1(config-router)#do sh ip eigrp top 3.3.3.3 255.255.255.255 IP-EIGRP (AS 10): Topology entry for 3.3.3.3/32 State is Passive, Query origin flag is 1, 1 Successor(s), FD is 409600 Routing Descriptor Blocks: 13.13.13.3 (FastEthernet0/0), from 13.13.13.3, Send flag is 0x0 Composite metric is (409600/128256), Route is Internal Vector metric: Minimum bandwidth is 10000 Kbit Total delay is 6000 microseconds Reliability is 255/255 Load is 1/255 Minimum MTU is 1500 Hop count is 1 12.12.12.2 (Serial0/0), from 12.12.12.2, Send flag is 0x0 Composite metric is (2323456/409600), Route is Internal Vector metric:
Minimum bandwidth is 1544 Kbit Total delay is 26000 microseconds Reliability is 255/255 Load is 1/255 Minimum MTU is 1500 Hop count is 2 R1(config-router)#do ping 3.3.3.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 3.3.3.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 100/147/220 ms R1(config-router)#do traceroute 3.3.3.3 Type escape sequence to abort. Tracing the route to 3.3.3.3
s
1 13.13.13.3 100 msec 116 msec * à langsung ke R3
ork er
========================================================================== Manipulasi trafik.... offset nya diset dengan nilai yang paling besar R1(config)#access-list 1 permit 3.3.3.3 R1(config)#router eigrp 10 R1(config-router)#offset-list 1 in ? <0-2147483647> Offset
R1(config-router)#offset-list 1 in 2147483647 fa0/0 Tunggu sebentar
ID-N etw
*Mar 1 00:19:32.619: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 10: Neighbor 13.13.13.3 (FastEthernet0/0) is resync: route configuration changed ========================================================================== Cek routing tabelnya lagi
R1(config-router)#do sh ip rou C
D
D
D C C
1.0.0.0/32 is subnetted, 1 subnets 1.1.1.1 is directly connected, Loopback0 2.0.0.0/32 is subnetted, 1 subnets 2.2.2.2 [90/435200] via 13.13.13.3, 00:10:12, FastEthernet0/0 3.0.0.0/32 is subnetted, 1 subnets 3.3.3.3 [90/2323456] via 12.12.12.2, 00:00:12, Serial0/0 à Jalurnya sudah lewat R2 23.0.0.0/24 is subnetted, 1 subnets 23.23.23.0 [90/307200] via 13.13.13.3, 00:10:13, FastEthernet0/0 12.0.0.0/24 is subnetted, 1 subnets 12.12.12.0 is directly connected, Serial0/0 13.0.0.0/24 is subnetted, 1 subnets 13.13.13.0 is directly connected, FastEthernet0/0
R1(config-router)#do ping 3.3.3.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 3.3.3.3, timeout is 2 seconds: !!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 44/104/196 ms R1(config-router)#do traceroute 3.3.3.3 Type escape sequence to abort. Tracing the route to 3.3.3.3 1 12.12.12.2 60 msec 96 msec 88 msec à jalurnya sudah pindah ke R2 dulu 2 23.23.23.3 144 msec 140 msec * R1(config-router)#do sh ip eigrp top 3.3.3.3 255.255.255.255
ork er
s
IP-EIGRP (AS 10): Topology entry for 3.3.3.3/32 State is Passive, Query origin flag is 1, 1 Successor(s), FD is 2323456 Routing Descriptor Blocks: 12.12.12.2 (Serial0/0), from 12.12.12.2, Send flag is 0x0 Composite metric is (2323456/409600), Route is Internal Vector metric: Minimum bandwidth is 1544 Kbit Total delay is 26000 microseconds Reliability is 255/255 Load is 1/255 Minimum MTU is 1500 Hop count is 2
ID-N etw
13.13.13.3 (FastEthernet0/0), from 13.13.13.3, Send flag is 0x0 Composite metric is (2147893247/128256), Route is Internal à nilai offset yang dikonfigurasikan Vector metric: Minimum bandwidth is 10000 Kbit Total delay is 83892079 microseconds Reliability is 255/255 Load is 1/255 Minimum MTU is 1500 Hop count is 1
========================================================================== Selanjutnya interface s0/0 pada R1 dishutdown dan trafik kembali ke jalur semula karena jalur hasil manipulasi diputus. R1(config-router)#int s0/0 R1(config-if)#shutdown R1(config-if)# *Mar 1 00:34:28.587: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 10: Neighbor 12.12.12.2 (Serial0/0) is down: interface down *Mar 1 00:34:30.483: %LINK-5-CHANGED: Interface Serial0/0, changed state to administratively down *Mar 1 00:34:31.483: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to down R1(config-if)#do sh ip rou
1.0.0.0/32 is subnetted, 1 subnets C 1.1.1.1 is directly connected, Loopback0 2.0.0.0/32 is subnetted, 1 subnets D 2.2.2.2 [90/435200] via 13.13.13.3, 00:25:07, FastEthernet0/0 3.0.0.0/32 is subnetted, 1 subnets D 3.3.3.3 [90/2147893247] via 13.13.13.3, 00:00:10, FastEthernet0/0 à langsung ke R3 23.0.0.0/24 is subnetted, 1 subnets
D
23.23.23.0 [90/307200] via 13.13.13.3, 00:25:07, FastEthernet0/0 12.0.0.0/24 is subnetted, 1 subnets D 12.12.12.0 [90/2221056] via 13.13.13.3, 00:00:10, FastEthernet0/0 13.0.0.0/24 is subnetted, 1 subnets C 13.13.13.0 is directly connected, FastEthernet0/0 R1(config-if)#do sh ip eigrp top 3.3.3.3 255.255.255.255 IP-EIGRP (AS 10): Topology entry for 3.3.3.3/32 State is Passive, Query origin flag is 1, 1 Successor(s), FD is 2323456 Routing Descriptor Blocks:
ork er
s
13.13.13.3 (FastEthernet0/0), from 13.13.13.3, Send flag is 0x0 Composite metric is (2147893247/128256), Route is Internal Vector metric: Minimum bandwidth is 10000 Kbit Total delay is 83892079 microseconds Reliability is 255/255 Load is 1/255 Minimum MTU is 1500 Hop count is 1
R1(config-if)#do ping 3.3.3.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 3.3.3.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 52/104/136 ms
ID-N etw
R1(config-if)#do traceroute 3.3.3.3 Type escape sequence to abort. Tracing the route to 3.3.3.3
1 13.13.13.3 144 msec 120 msec *
Ok sudah kembali ke jalan yang benar.....
12. EIGRP Traffic Engineering – AD 12.12.12.1/24 12.12.12.2/24 13.13.13.1/24
23.23.23.2/24
s
23.23.23.3/24
ork er
13.13.13.3/24
Diinginkan trafik dari R1 menuju Loopback R3 dilewatkan ke R2 terlebih dahulu, namun kali ini dengan metode memanipulasi Administrative Distance nya Kembalikan dulu hasil konfigurasi sebelumnya R1(config)#int s0/0 R1(config-if)#no shutdown
R1(config-if)#router eigrp 10 R1(config-router)#no offset-list 1 in 2147483647 fa0/0
ID-N etw
========================================================================== Konfigurasikan manipulasi AD nya, diset paling besar nilainya yakni 255 R1(config-if)#router eigrp 10 R1(config-router)#distance 255 ? A.B.C.D IP Source address
R1(config-router)#distance 255 13.13.13.1 ? A.B.C.D Wildcard bits
R1(config-router)#distance 255 13.13.13.1 0.0.0.0 ? <1-99> IP Standard access list number <1300-1999> IP Standard expanded access list number WORD Standard access-list name
R1(config-router)#distance 255 13.13.13.0 0.0.0.255 1 R1(config)#access-list 1 permit 3.3.3.3 ========================================================================== Cek hasilnya gan….. R1(config-router)#do sh ip route 1.0.0.0/32 is subnetted, 1 subnets
C
1.1.1.1 is directly connected, Loopback0 2.0.0.0/32 is subnetted, 1 subnets D 2.2.2.2 [90/435200] via 13.13.13.3, 00:00:03, FastEthernet0/0 3.0.0.0/32 is subnetted, 1 subnets D 3.3.3.3 [90/2323456] via 12.12.12.2, 00:00:05, Serial0/0 à pindah jalur ke Router R2 via serial 23.0.0.0/24 is subnetted, 1 subnets D 23.23.23.0 [90/307200] via 13.13.13.3, 00:00:03, FastEthernet0/0 12.0.0.0/24 is subnetted, 1 subnets C 12.12.12.0 is directly connected, Serial0/0 13.0.0.0/24 is subnetted, 1 subnets C 13.13.13.0 is directly connected, FastEthernet0/0 R1(config-router)#
ork er
s
R1(config-router)#do ping 3.3.3.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 3.3.3.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/121/208 ms R1(config-router)#do trac 3.3.3.3 Type escape sequence to abort. Tracing the route to 3.3.3.3
ID-N etw
1 12.12.12.2 84 msec 96 msec 260 msec 2 23.23.23.3 184 msec 296 msec *
ID-N etw
===== R1 ===== en conf t hostname R1
ork er
s
13. EIGRP Load Balancing
int f0/0 ip addr 12.12.12.1 255.255.255.0 no sh int f0/1 ip addr 13.13.13.1 255.255.255.0 no sh int lo0 ip addr 1.1.1.1 255.255.255.255 router eigrp 10 net 0.0.0.0 no auto-summary ===== R2 ===== en conf t hostname R2 int f0/0
ip addr 12.12.12.2 255.255.255.0 no sh int f0/1 ip addr 24.24.24.2 255.255.255.0 no sh int lo0 ip addr 2.2.2.2 255.255.255.255
ork er
===== R3 ===== en conf t hostname R3
s
router eigrp 10 net 0.0.0.0 no auto-summary
int f0/0 ip addr 13.13.13.3 255.255.255.0 no sh int f0/1 ip addr 34.34.34.3 255.255.255.0 no sh
ID-N etw
int lo0 ip addr 3.3.3.3 255.255.255.255 router eigrp 10 net 0.0.0.0 no auto-summary
===== R4 ===== en conf t hostname R4
int f0/0 ip addr 24.24.24.4 255.255.255.0 no sh int f0/1 ip addr 34.34.34.4 255.255.255.0 no sh
int lo0 ip addr 4.4.4.4 255.255.255.255
ID-N etw
ork er
s
router eigrp 10 net 0.0.0.0 no auto-summary
================================================================ selanjutnya cek routing tabelnya R1#sh ip route eigrp 34.0.0.0/24 is subnetted, 1 subnets D 34.34.34.0 [90/307200] via 13.13.13.3, 00:00:28, FastEthernet0/1 2.0.0.0/32 is subnetted, 1 subnets D 2.2.2.2 [90/409600] via 12.12.12.2, 00:00:28, FastEthernet0/0 3.0.0.0/32 is subnetted, 1 subnets D 3.3.3.3 [90/409600] via 13.13.13.3, 00:00:28, FastEthernet0/1 4.0.0.0/32 is subnetted, 1 subnets D 4.4.4.4 [90/435200] via 13.13.13.3, 00:00:28, FastEthernet0/1 [90/435200] via 12.12.12.2, 00:00:28, FastEthernet0/0 24.0.0.0/24 is subnetted, 1 subnets D 24.24.24.0 [90/307200] via 12.12.12.2, 00:00:28, FastEthernet0/0
ork er
s
seperti yang terlihat diatas, 2 jalur digunakan secara bersamaan untuk menuju ke Loopback0 R4 (Equal Cost Load Balancing) yakni via R2 (12.12.12.2) dan R3 (13.13.13.3)
ID-N etw
R1#sh ip route 4.4.4.4 Routing entry for 4.4.4.4/32 Known via "eigrp 10", distance 90, metric 435200, type internal Redistributing via eigrp 10 Last update from 13.13.13.3 on FastEthernet0/1, 00:00:31 ago Routing Descriptor Blocks: 13.13.13.3, from 13.13.13.3, 00:00:31 ago, via FastEthernet0/1 Route metric is 435200, traffic share count is 1 Total delay is 7000 microseconds, minimum bandwidth is 10000 Kbit Reliability 255/255, minimum MTU 1500 bytes Loading 1/255, Hops 2
* 12.12.12.2, from 12.12.12.2, 00:00:31 ago, via FastEthernet0/0 Route metric is 435200, traffic share count is 1 Total delay is 7000 microseconds, minimum bandwidth is 10000 Kbit Reliability 255/255, minimum MTU 1500 bytes Loading 1/255, Hops 2
================================================================ Unequal Cost Load Balancing selanjutnya kita rubah bandwidth menjadi lebih kecil dari 10000 Kbit pada Link yang menuju ke router R2, misalkan 1000 Kbit R1(config)#int f0/0 R1(config-if)#bandwidth 1000 R1(config-if)#do clear ip route *
cek lagi pada routing tabelnya dan didapati hanya satu jalur yang dilewati yakni melalui R3 R1#sh ip route 34.0.0.0/24 is subnetted, 1 subnets D 34.34.34.0 [90/307200] via 13.13.13.3, 00:00:11, FastEthernet0/1 1.0.0.0/32 is subnetted, 1 subnets C 1.1.1.1 is directly connected, Loopback0 2.0.0.0/32 is subnetted, 1 subnets D 2.2.2.2 [90/460800] via 13.13.13.3, 00:00:11, FastEthernet0/1
D D D C C
[90/2713600] via 12.12.12.2, 00:00:11, FastEthernet0/0 3.0.0.0/32 is subnetted, 1 subnets 3.3.3.3 [90/409600] via 13.13.13.3, 00:00:11, FastEthernet0/1 4.0.0.0/32 is subnetted, 1 subnets 4.4.4.4 [90/435200] via 13.13.13.3, 00:00:11, FastEthernet0/1 24.0.0.0/24 is subnetted, 1 subnets 24.24.24.0 [90/332800] via 13.13.13.3, 00:00:11, FastEthernet0/1 12.0.0.0/24 is subnetted, 1 subnets 12.12.12.0 is directly connected, FastEthernet0/0 13.0.0.0/24 is subnetted, 1 subnets 13.13.13.0 is directly connected, FastEthernet0/1
berikutnya kita cek dulu di eigrp topologinya yang masih menyimpan tentang jalur lain yang kita rubah bandwidthnya menjadi lebih kecil
ork er
s
R1#sh ip eigrp topology 4.4.4.4/32 IP-EIGRP (AS 10): Topology entry for 4.4.4.4/32 State is Passive, Query origin flag is 1, 1 Successor(s), FD is 435200 Routing Descriptor Blocks: 13.13.13.3 (FastEthernet0/1), from 13.13.13.3, Send flag is 0x0 Composite metric is (435200/409600), Route is Internal Vector metric: Minimum bandwidth is 10000 Kbit Total delay is 7000 microseconds Reliability is 255/255 Load is 1/255 Minimum MTU is 1500 Hop count is 2
ID-N etw
12.12.12.2 (FastEthernet0/0), from 12.12.12.2, Send flag is 0x0 Composite metric is (2739200/409600), Route is Internal Vector metric: Minimum bandwidth is 1000 Kbit Total delay is 7000 microseconds Reliability is 255/255 Load is 1/255 Minimum MTU is 1500 Hop count is 2
Perhatikan nilai metric nya..... untuk mencari nilai varience yang akan kita masukkan, maka 2739200 dibagi 435200 = 6,29 maka nilai varience yang diset adalah 7 (pembulatan harus keatas utk nilai berapapun) R1(config)#router eigrp 10 R1(config-router)#variance 7
================================================================ hasil akhir R1#sh ip route 34.0.0.0/24 is subnetted, 1 subnets D 34.34.34.0 [90/307200] via 13.13.13.3, 00:00:01, FastEthernet0/1 1.0.0.0/32 is subnetted, 1 subnets C 1.1.1.1 is directly connected, Loopback0 2.0.0.0/32 is subnetted, 1 subnets
D
2.2.2.2 [90/460800] via 13.13.13.3, 00:00:01, FastEthernet0/1 [90/2713600] via 12.12.12.2, 00:00:01, FastEthernet0/0 3.0.0.0/32 is subnetted, 1 subnets D 3.3.3.3 [90/409600] via 13.13.13.3, 00:00:01, FastEthernet0/1 4.0.0.0/32 is subnetted, 1 subnets D 4.4.4.4 [90/435200] via 13.13.13.3, 00:00:01, FastEthernet0/1 [90/2739200] via 12.12.12.2, 00:00:01, FastEthernet0/0 24.0.0.0/24 is subnetted, 1 subnets
ork er
s
R1#sh ip route 4.4.4.4 Routing entry for 4.4.4.4/32 Known via "eigrp 10", distance 90, metric 435200, type internal Redistributing via eigrp 10 Last update from 12.12.12.2 on FastEthernet0/0, 00:00:47 ago Routing Descriptor Blocks: * 13.13.13.3, from 13.13.13.3, 00:00:47 ago, via FastEthernet0/1 Route metric is 435200, traffic share count is 120 Total delay is 7000 microseconds, minimum bandwidth is 10000 Kbit Reliability 255/255, minimum MTU 1500 bytes Loading 1/255, Hops 2 12.12.12.2, from 12.12.12.2, 00:00:47 ago, via FastEthernet0/0 Route metric is 2739200, traffic share count is 19 Total delay is 7000 microseconds, minimum bandwidth is 1000 Kbit Reliability 255/255, minimum MTU 1500 bytes Loading 1/255, Hops 2
ID-N etw
Seperti yang terlihat sekarang 2 jalur digunakan secara bersamaan, namun dengan pembagian setiap 7 paket dkirimkan melalui link utama, maka berikutnya 1 paket dkirimkan ke link kedua