S2G Optimizer
Soft2get Manual S2G Optimizer Last modifications: 02/05/2005
1. NEDERLANDS __________________________________________________________ 1 1.1. Hoofdscherm __________________________________________________________________ 1 1.2. Nieuwe klant/dossier ____________________________________________________________ 2 1.3. Nieuw dossier “panelen” (2D) ____________________________________________________ 2 1.4. Nieuw dossier “profielen” (1D)____________________________________________________ 3 1.5. Verwijderen van dossier/klant ____________________________________________________ 4 1.6. Paneelbibliotheek_______________________________________________________________ 4 1.7. Import CSV-bestanden __________________________________________________________ 4 1.8. Berekeningsresultaat bij “Panelen” (2D) ___________________________________________ 5 1.9. Berekeningsresultaat bij “Profielen” (1D) __________________________________________ 7 1.10. Afdrukken __________________________________________________________________ 8 1.11. Opties ______________________________________________________________________ 9 1.11.1. Optimalisatie van panelen _____________________________________________________ 9 1.11.2. Optimalisatie van profielen ____________________________________________________ 14 1.11.3. Voorstelling berekeningsresultaat _______________________________________________ 14 1.11.4. Afdrukvoorbeeld ____________________________________________________________ 15 1.11.5. Taalkeuze__________________________________________________________________ 15 1.11.6. Import CSV-bestanden _______________________________________________________ 16 2. FRANÇAIS _____________________________________________________________ 17 2.1. Menu principal ________________________________________________________________ 17 2.2. Nouveau client/dossier___________________________________________________________ 18 2.3. Nouveau dossier “panneaux” (2D) ________________________________________________ 18 2.4. Nouveau dossier “profilés” (1D) __________________________________________________ 19 2.5. Suppression d’un dossier/client ___________________________________________________ 21 2.6. Bibliothèque des panneaux _______________________________________________________ 21 2.7. Importation fichier “CSV” _______________________________________________________ 21 2.8. Résultat calcul “Panneaux” (2D) __________________________________________________ 22 2.9. Résultat calcul “Profilés” (1D) ____________________________________________________ 24 2.10. Impression __________________________________________________________________ 26 2.11. Options _____________________________________________________________________ 27 2.11.1. Optimisation des panneaux (2D) ________________________________________________ 27 2.11.2. Optimisation des profilés (1D) _________________________________________________ 32 2.11.3. Présentation du résultat à l’écran________________________________________________ 32 2.11.4. Concernant aperçu de l’impression à l’écran_______________________________________ 33 2.11.5. Choix des langues ___________________________________________________________ 33 2.11.6. Concernant l’importation des fichiers CSV________________________________________ 34 3. ENGLISH_______________________________________________________________ 35 3.1. Main menu ____________________________________________________________________ 35 3.2. New customer/project ___________________________________________________________ 36 3.3. New project “panels” (2D) _______________________________________________________ 36 3.4. New project “profiles” (1D) ______________________________________________________ 37 3.5. Delete a project/customer ________________________________________________________ 38 3.6. Library of standard panels _______________________________________________________ 38 3.7. Import « CSV »-files ____________________________________________________________ 38 3.8. Optimisation result “Panels” (2D) _________________________________________________ 39 3.9. Optimisation result “Profiles” (1D) ________________________________________________ 41 3.10. Print _______________________________________________________________________ 42 3.11. Options _____________________________________________________________________ 43 3.11.1. Optimisation of panels (2D) ___________________________________________________ 43 3.11.2. Optimisation of profiles (1D) __________________________________________________ 47 3.11.3. Screen presentation __________________________________________________________ 47 3.11.4. Print preview _______________________________________________________________ 48 3.11.5. Languages _________________________________________________________________ 48 3.11.6. Import of CSV-files __________________________________________________________ 49
Contact information :
by mail
website address
www.soft2get.com
[email protected]
Your partner in finding solutions
1. Nederlands Met S2G_Optimizer kunt u - op een heel eenvoudige manier - profielen en panelen optimaliseren onafhankelijk van enig ander berekeningspakket. Wanneer u het programma voor de eerste keer gebruikt, dient u een codenummer op te geven. Contacteer Soft2get om dit nummer te verkrijgen (of stuur een mail naar
[email protected]).
1.1. Hoofdscherm
S2G_Optimizer onderscheidt twee modes, namelijk : -
het optimaliseren van profielen
(1D)
-
het optimaliseren van panelen
(2D)
Om over te schakelen naar uw dossiers betreffende panelen of profielen, selecteert u het overeenkomstige icoontje.
Handleiding S2G_Optimizer
1
V1.0
Your partner in finding solutions
1.2. Nieuwe klant/dossier Bij het creëren van een nieuw dossier wordt automatisch de naam “New” voorgesteld. U bent verplicht deze naam te wijzigen. Opgelet, u kunt geen twee dossiers/klanten met dezelfde naam creëren.
1.3. Nieuw dossier “panelen” (2D) Bij het aanklikken van een dossier krijgt u een overzichtstabel met alle te optimaliseren stukken.
Onderaan de tabel vindt u de nodige functies om enerzijds nieuwe stukken toe te voegen en anderzijds bestaande stukken te verwijderen.
Handleiding S2G_Optimizer
2
V1.0
Your partner in finding solutions Bij een niet rechthoekig stuk dienen de overmeten maten ingebracht te worden. Voor een cirkel wordt dit de diameter, voor een trapezium de totale breedte x de totale hoogte. Bij rechthoekige driehoeken moet men het totale aantal delen door twee.
1.4. Nieuw dossier “profielen” (1D) Bij het aanklikken van een dossier krijgt u een overzichtstabel met alle te verzagen stukken.
Het verwijderen van een bepaald profiel kan hier gebeuren door de volledige lijn te selecteren en op de [Delete]toets te klikken.
Handleiding S2G_Optimizer
3
V1.0
Your partner in finding solutions
1.5. Verwijderen van dossier/klant Aan de hand van uw selectie (klant of dossier) wordt er een bevestiging gevraagd of u het element wel degelijk wenst te verwijderen. Opgepast, bij het verwijderen van een klant worden automatisch alle dossiers die aan deze klant gekoppeld zijn, verwijderd!
1.6. Paneelbibliotheek Bij het optimaliseren van panelen kunt u vooraf een onbeperkt aantal type standaardpanelen definiëren.
1.7. Import CSV-bestanden Via deze functie kunt u gestructureerde ASCII-bestanden (tekstformaat) afkomstig van externe programma’s (bvb. Excel,…) importeren. Het creëren van één of meerdere bestandsformaten (filters) gebeurt in de opties (zie 1.11.6) Opgelet: Deze functie is enkel actief wanneer nog geen enkel stuk in de tabel werd ingebracht!
Handleiding S2G_Optimizer
4
V1.0
Your partner in finding solutions
1.8. Berekeningsresultaat bij “Panelen” (2D) Nadat u het paneel van waaruit u de stukken wenst te verzagen en eventueel het zaagverlies en de haaksheid van dit paneel heeft aangeduid, klikt u op het rekenmachientje om de optimalisatie te starten :
Op het einde van de berekening krijgt u het volgende resultaat :
Handleiding S2G_Optimizer
5
V1.0
Your partner in finding solutions Na berekening kunt u d.m.v. het aanklikken van een bepaald stuk in de tabel controleren waar dit stuk zich overal bevindt in de te verzagen panelen.
Door de muis over de panelen te laten glijden bekomt men meer info betreffende het stuk.
Na berekening kunt u d.m.v. de simulatieknop zien op welke manier en volgorde S2G_Optimizer het paneel verzaagt:
Handleiding S2G_Optimizer
6
V1.0
Your partner in finding solutions
1.9. Berekeningsresultaat bij “Profielen” (1D) Nadat u de profielreferentie van waaruit u de stukken wenst te verzagen en eventueel het zaagverlies, de profiellengte en het verlies aan de uiteinden heeft aangeduid, klikt u op het rekenmachientje om de optimalisatie te starten :
Op het einde van de berekening krijgt u het volgende resultaat :
Handleiding S2G_Optimizer
7
V1.0
Your partner in finding solutions
1.10. Afdrukken U krijgt steeds een afdrukvoorbeeld te zien vooraleer u kunt afdrukken.
Via deze icoontjes kunt u meerdere pagina’s overlopen, in of uitzoomen en de afdruk bevestigen.
Handleiding S2G_Optimizer
8
V1.0
Your partner in finding solutions
1.11.Opties 1.11.1. Optimalisatie van panelen De opties betreffende de optimalisatiemethode worden per dossier opgeslagen!
Berekeningsmethode :
1.11.1.1.
Volgens oppervlak
Bij deze berekeningsroutine wordt eerst het grootste stuk in het paneel geplaatst. In het resterende vlak worden opnieuw eerst de grootste resterende stukken geplaatst.
Handleiding S2G_Optimizer
9
V1.0
Your partner in finding solutions
Handleiding S2G_Optimizer
10
V1.0
Your partner in finding solutions 1.11.1.2.
Volgens verlies
Bij deze berekeningsroutine wordt eerst het stuk geplaatst dat het minst snijverlies in absolute oppervlak (m²) met zich teweegbrengt. Voor het resterend vlak wordt dezelfde werkwijze toegepast, opnieuw komt het stuk met het minst snijverlies in absolute oppervlak eerst.
Het stuk van 0.9m x 0.4m genereert een absoluut snijverlies van 0.2m x 0.4m = 0.08m²
Het stuk van 1m x 0.9m genereert een absoluut snijverlies van 0.1m x 0.9m = 0.09m²
Handleiding S2G_Optimizer
11
V1.0
Your partner in finding solutions 1.11.1.3.
Procentueel
Bij deze berekeningsroutine wordt eerst het stuk geplaatst dat het minst procentueel snijverlies (%) t.o.v. het stuk zelf met zich teweegbrengt. Voor het resterend vlak wordt dezelfde werkwijze toegepast, opnieuw komt het stuk met het minst procentueel snijverlies (%) t.o.v. het stuk zelf eerst.
Dit stuk van 1m x 0.9m genereert een relatief snijverlies van (0.1x0.9)/(1x0.9)*100 = 10%
Dit stuk van 0.4m x 0.9m genereert een relatief snijverlies van (0.7x0.9)/(0.4x0.9)*100 = 175%
Handleiding S2G_Optimizer
12
V1.0
Your partner in finding solutions 1.11.1.4.
Snel <> Nauwkeurig
Bij de nauwkeurige berekeningsmethode worden meer iteraties overlopen, waardoor uw rekensnelheid vertraagt maar uw eindresultaat nauwkeuriger wordt.
1.11.1.5.
Optimalisatie zaagsneden :
In bepaalde gevallen is het interessanter om het totaal aantal meter zaagsnede te beperken en zich niet te focussen op een minimaal restverlies. Dit kan bekomen worden door S2G_Optimizer alle stukken met één gelijke afmeting te laten groeperen, voor zover deze groep nog in het paneel past. Hoe meer stukken met eenzelfde afmeting samen gegroepeerd worden, hoe minder meter zaagsnede er nodig zal zijn.
Deze 5 stukken worden gegroepeerd en samen geoptimaliseerd.
1.11.1.6.
Limieten langste zaagsnede
Met deze optie kan de maximale zaagsnede in [mm] van de snijmachine ingesteld worden.
Handleiding S2G_Optimizer
13
V1.0
Your partner in finding solutions
1.11.2. Optimalisatie van profielen De opties betreffende de optimalisatiemethode worden per dossier opgeslagen! Bij de nauwkeurige berekeningsmethode worden meer iteraties overlopen, waardoor uw rekensnelheid vertraagt maar uw eindresultaat nauwkeuriger wordt.
1.11.3. Voorstelling berekeningsresultaat
Handleiding S2G_Optimizer
14
V1.0
Your partner in finding solutions
1.11.4. Afdrukvoorbeeld Aan de hand van uw printereigenschappen kunt u hier de marges bepalen in mm. Tevens kunt u aanduiden hoeveel panelen er grafisch moeten voorgesteld worden horizontaal en/of verticaal.
1.11.5. Taalkeuze
Handleiding S2G_Optimizer
15
V1.0
Your partner in finding solutions
1.11.6. Import CSV-bestanden In dit scherm kunt u één of meerdere bestandsformaten instellen. Deze “stuk”-lijsten kunnen dan geïmporteerd worden in een bestaand leeg dossier.
-
Scheidingsteken = “,” Eerste rij met in te lezen gegevens =2 Filter, importeer enkel gegevens met waarde = 5 in kolom 1 (optioneel) Filter, importeer enkel gegevens met waarde = 26v in kolom 2 (optioneel) Kolom lengte = kolom 0 (niet van toepassing bij panelen) Kolom breedte = kolom 5 (niet van toepassing bij profielen) Kolom hoogte = kolom 6 (niet van toepassing bij profielen) Kolom aantal = kolom 4 Kolom hoek links = kolom 0 (niet van toepassing bij panelen) Kolom hoek rechts = kolom 0 (niet van toepassing bij panelen)
Bvb: Deze voorgaande instellingen van een CSV-formaat (Comma Separated Values) zijn correct om het volgende ASCII-bestand te kunnen inlezen : "INFO","test1","divers","Production","C:\Facalog\Projects\Project.jpg" "1","52A10","AFDEKPROFIEL","14","7000","1048599","1048599" "1","52R52","STIJL","6","7000","1048679","1048679" "1","PV001","THERM. ONDERBREKING","23","7000","","" "2","52R223","RUBBER","25","7000" "2","52R226"," RUBBER ","4","7000" "3","83Z639","SCHROEF","40" "5","26v","","1","1403","1202","0","0","0" "5","26v","","1","1478","1202","0","0","0" "5","26v","","1","1478","1202","0","0","0" "5","26v","","1","1452","1202","0","0","0" "5","26v","","1","1478","1228","0","0","0" "5","26v","","1","1452","1228","0","0","0" "5","26v","","1","1403","1202","0","0","0" "5","26v","","1","1403","1228","0","0","0" "5","26v","","1","1478","1202","0","0","0" "5","26v","","1","1478","1228","0","0","0" "5","26v","","1","1478","1202","0","0","0" "5","26v","","1","1478","1228","0","0","0" "5","26v","","1","1452","1202","0","0","0"
Handleiding S2G_Optimizer
16
V1.0
Your partner in finding solutions
2. Français S2G_Optimizer vous permet d’optimiser les profilés et panneaux d’une manière très simple et indépendant d’un autre logiciel de calcul. Avant de pouvoir lancer le programme, un numéro de code est exigé. Veuillez contacter Soft2get pour obtenir ce numéro (ou envoyez un mail à
[email protected]).
2.1. Menu principal
S2G_Optimzer distingue deux modes, c’est à dire : -
l’optimisation des profilés
(1D)
-
l’optimisation des panneaux
(2D)
Pour passer aux projets concernant les panneaux ou profilés, vous devez sélectionner l’icône correspondant.
Manuel S2G_Optimizer
17
V1.0
Your partner in finding solutions
2.2. Nouveau client/dossier Pendant la création d’un nouveau dossier ou client, le nom « New » sera automatiquement proposé. Vous êtes obligé de modifier ce nom. C’est impossible de choisir un nom qui existe déjà..
2.3. Nouveau dossier “panneaux” (2D) En cliquant sur le nom du dossier, vous obtenez un tableau contenant un résumé de toutes les pièces à optimiser.
En bas de l’écran, vous retrouvez les fonctions nécessaires pour pouvoir ajouter des pièces et d’autre part pour pouvoir supprimer certains pièces.
Manuel S2G_Optimizer
18
V1.0
Your partner in finding solutions Pour une forme non rectangulaire, les dimensions extrêmes doivent être saisies. Il s’agit du diamètre d’un cercle et les dimensions hors tout pour un trapèze. En cas des triangles rectangles, vous devez diviser la quantité totale des triangles par deux.
2.4. Nouveau dossier “profilés” (1D) En cliquant sur le nom du dossier, vous obtenez un tableau contenant un résumé de toutes les pièces à débiter et à optimiser.
Manuel S2G_Optimizer
19
V1.0
Your partner in finding solutions La suppression d’une pièce peut se faire en sélectionnant la ligne compète et, ensuite, taper sur la touche [Suppr].
Manuel S2G_Optimizer
20
V1.0
Your partner in finding solutions
2.5. Suppression d’un dossier/client Conformément à la sélection (client ou projet), le programme vous demande de confirmer la suppression de l’élément. Attention, la suppression d’un client provoquera la suppression de tous les projets appartenant à ce client!
2.6. Bibliothèque des panneaux Dans la bibliothèque, vous avez la possibilité de définir plusieurs panneaux standards. Avant le lancement d’optimisation d’un projet, vous pouvez éventuellement choisir un de ces panneaux.
2.7. Importation fichier “CSV” Cette fonction vous permet d’importer des fichiers ASCII structurés. Ces fichiers « textes » peuvent être générés par autres logiciels (p.ex. Excel,…). La création d’une ou plusieurs filtres (format de fichier) se passe dans les options(voir 2.11.6). L’icône est activé si le projet ne contient aucune pièce! (donc, seulement dans un nouveau projet)
Manuel S2G_Optimizer
21
V1.0
Your partner in finding solutions
2.8. Résultat calcul “Panneaux” (2D) Après le choix d’un panneau « bibliothèque » ou après le changement de la largeur et l’hauteur, vous cliquez sur la calculatrice pour fair lancer le calcul d’optimisation. N’oubliez pas d’indiquer le trait de scie et la perte à cause d’une mauvaise orthogonalité des panneaux :
À la fin du calcul, vous obtenez le résultat suivant :
Manuel S2G_Optimizer
22
V1.0
Your partner in finding solutions À la fin du calcul, vous pouvez, en cliquant sur une pièce dans le tableau, contrôler à quelle position la pièce est située dans les panneaux découpés.
Laisser glisser la souris sur une pièce pour obtenir plus d’information.
À la fin du calcul, on peut laisser simuler de quelle manière S2G_Optimizer a découpé le panneau:
Manuel S2G_Optimizer
23
V1.0
Your partner in finding solutions
2.9. Résultat calcul “Profilés” (1D) Après l’indication de la référence profilé, vous cliquez sur la calculatrice pour fair lancer le calcul d’optimisation. N’oubliez pas d’indiquer la longueur du profilé, le trait de scie et la perte en bout de barre:
À la fin du calcul, vous obtenez le résultat suivant :
Manuel S2G_Optimizer
24
V1.0
Your partner in finding solutions
Manuel S2G_Optimizer
25
V1.0
Your partner in finding solutions
2.10.Impression Avant d’imprimer, il y a toujours une visualisation à l’écran.
Les icônes vous permettent de visualiser plusieurs pages, d’agrandir et de confirmer l’impression.
Manuel S2G_Optimizer
26
V1.0
Your partner in finding solutions
2.11.Options 2.11.1. Optimisation des panneaux (2D) Les options concernant la méthode d’optimisation seront enregistrées par dossier !
Méthode de calcul :
2.11.1.1.
Selon surface
Cet algorithme pose d’abord la plus grande pièce dans le panneau. Dans la partie restante, de nouveau, la plus grande pièce possible sera être posée.
Manuel S2G_Optimizer
27
V1.0
Your partner in finding solutions
Manuel S2G_Optimizer
28
V1.0
Your partner in finding solutions 2.11.1.2.
Selon perte absolue
Cet algorithme pose d’abord la pièce qui provoque la moindre perte de scie en surface absolue (m²). Dans la partie restante, de nouveau, cette pièce sera recherchée qui répond à la même condition.
La pièce de 0.9m x 0.4m génère une perte en surface absolue de 0.2m x 0.4m = 0.08m²
La pièce de 1m x 0.9m génère une perte en surface absolue de 0.1m x 0.9m = 0.09m²
Manuel S2G_Optimizer
29
V1.0
Your partner in finding solutions 2.11.1.3.
Selon “procentuel” (perte relative)
Cet algorithme pose d’abord la pièce qui provoque la moindre perte de scie en surface relative (%) par rapport à la pièce même. Dans la partie restante, de nouveau, cette pièce sera recherchée qui répond à la même condition.
La pièce de 1m x 0.9m génère une perte en surface relative de (0.1x0.9)/(1x0.9)*100 = 10%
La pièce de 0.4m x 0.9m génère une perte en surface relative de (0.7x0.9)/(0.4x0.9)*100 = 175%
Manuel S2G_Optimizer
30
V1.0
Your partner in finding solutions 2.11.1.4.
Vite <> Précis
La méthode « précis » évoque plus d’itérations avant de finaliser le calcul d’optimisation. Ceci peut réduire la vitesse de calcul, mais augmente la précision des calculs.
2.11.1.5.
Optimisation longueur totale des coupes
Dans certains cas, c’est plus intéressant de limiter la longueur totale des coupes au lieu de limiter la chute. Ceci peut être obtenu par S2G_Optimizer en groupant toutes les pièces qui ont au moins une dimension qui est la même dans la mesure où ce groupe s’ajuste au panneau. Plus de pièces qui ont été groupées moins la longueur des coupes.
Les 5 pièces sont groupées et optimalisées ensemble.
2.11.1.6.
Longueur de coupe maximale
Cette option peut limiter la longueur de scie maximale en [mm] de la machine.
Manuel S2G_Optimizer
31
V1.0
Your partner in finding solutions
2.11.2. Optimisation des profilés (1D) Les options concernant la méthode d’optimisation seront enregistrées par dossier ! La méthode « précis » évoque plus d’itérations avant de finaliser le calcul d’optimisation. Ceci peut réduire la vitesse de calcul.
2.11.3. Présentation du résultat à l’écran
Manuel S2G_Optimizer
32
V1.0
Your partner in finding solutions
2.11.4. Concernant aperçu de l’impression à l’écran D’après les propriétés de l’imprimante, vous pouvez définir les marges en [mm]. Vous devez aussi indiquer le nombre de panneau à imprimer horizontalement et verticalement.
2.11.5. Choix des langues
Manuel S2G_Optimizer
33
V1.0
Your partner in finding solutions
2.11.6. Concernant l’importation des fichiers CSV L’utilisateur peut définir un ou plusieurs format de fichier. Ensuite, ces fichiers ASCII peuvent être importés dans un projet qui ne contient aucune pièce.
-
Séparateur = “,” Première ligne contenant les données =2 Filtre, importer seulement les données qui ont une valeur = 5 dans colonne 1 (optionnel) Filtre, importer seulement les données qui ont une valeur = 26v dans colonne 2 (optionnel) Colonne contenant longueur de la pièce à couper = col 0 (n’est pas applicable aux panneaux) Colonne contenant largeur de la pièce = col 5 (n’est pas applicable aux profilés) Colonne contenant hauteur de la pièce = col 6 (n’est pas applicable aux profilés) Colonne contenant nombre de pièces = col 4 Colonne contenant angle gauche de la pièce = col 0 (n’est pas applicable aux panneaux) Colonne contenant angle droite de la pièce = col 0 (n’est pas applicable aux panneaux)
Ex. : Les paramètres précédentes d’un format CSV (Comma Separated Values) sont corrects pour pouvoir importer le fichier-ASCII suivant : "INFO","test1","divers","Production","C:\Facalog\Projects\Project.jpg" "1","52A10","CAPOT","14","7000","1048599","1048599" "1","52R52","EPINE","6","7000","1048679","1048679" "1","PV001","RUPTURE THERM.","23","7000","","" "2","52R223","JOINT","25","7000" "2","52R226"," JOINT ","4","7000" "3","83Z639","VIS","40" "5","20v","","1","1403","1202","0","0","0" "5","20v","","1","1478","1202","0","0","0" "5","20v","","1","1478","1202","0","0","0" "5","20v","","1","1452","1202","0","0","0" "5","20v","","1","1478","1228","0","0","0" "5","20v","","1","1452","1228","0","0","0" "5","20v","","1","1403","1202","0","0","0" "5","20v","","1","1403","1228","0","0","0" "5","20v","","1","1478","1202","0","0","0" "5","20v","","1","1478","1228","0","0","0" "5","20v","","1","1478","1202","0","0","0" "5","20v","","1","1478","1228","0","0","0" "5","20v","","1","1452","1202","0","0","0"
Manuel S2G_Optimizer
34
V1.0
Your partner in finding solutions
3. English S2G_Optimizer is an independent calculation program that enables you to easily optimise profiles and panels. The first time you start the program, you will need a registration number. Please, contact Soft2get to obtain this number (or send a mail to
[email protected]).
3.1. Main menu
S2G_Optimizer distinguishes two modes : -
profile optimisation
(1D)
-
panel optimisation
(2D)
To switch between panel and profile projects, use the appropriate symbol.
Manual S2G_Optimizer
35
V1.0
Your partner in finding solutions
3.2. New customer/project The name “New” will automatically be proposed when you create a new customer or project. You must change this name. Note that you cannot choose an existing name.
3.3. New project “panels” (2D) After selecting a project, you get a list of the pieces that have to be optimised.
At the bottom, you will find a number of functions to add new or delete existing pieces.
Manual S2G_Optimizer
36
V1.0
Your partner in finding solutions For non-rectangular shapes, you must set the outer dimensions, e.g. the diameter for a circle, the overall width x height for a trapezium. In case of right-angled triangles, you must divide the total quantity by two.
3.4. New project “profiles” (1D) After selecting a project, you get a list of the pieces that have to be cut and optimised.
To delete a piece, select the whole line and click on the [Delete]-button.
Manual S2G_Optimizer
37
V1.0
Your partner in finding solutions
3.5. Delete a project/customer As a result of your selection (customer or project), the program will ask you to confirm whether the element has to be deleted or not. Attention, when you delete a customer, all projects belonging to this customer will also be deleted!
3.6. Library of standard panels It is possible to define one or more standard panels which you can then select before starting the project optimisation.
3.7. Import « CSV »-files This function allows you to import structured ASCII-files. Such “text”-files can be generated by other programs (e.g. Excel,…). To create one or more import filters, see options 3.11.6. To import an external list, the project must be empty. If not, the “import”-symbol is not activated.
Manual S2G_Optimizer
38
V1.0
Your partner in finding solutions
3.8. Optimisation result “Panels” (2D) Choose a (standard) panel and click on the calculator to start the optimisation. Do not forget to indicate the sawblade-width [mm] and the loss caused by bad perpendicularity of the panel.
At the end of the calculation, the following window is shown :
Manual S2G_Optimizer
39
V1.0
Your partner in finding solutions At the end of the calculation, you can select a piece to learn about its exact localisation in the optimised panels.
Move the mouse to get more information about the piece.
Moreover, you can simulate the calculated optimisation for each panel:
Manual S2G_Optimizer
40
V1.0
Your partner in finding solutions
3.9. Optimisation result “Profiles” (1D) Indicate the profile reference number and click on the calculator to start the optimisation. Do not forget to indicate the length of the profiles, the sawblade-width [mm] and the total loss at the ends of the profile :
At the end of the calculation, the following window is shown :
Manual S2G_Optimizer
41
V1.0
Your partner in finding solutions
3.10.Print If you want to print a document, you will always receive a preview first.
These buttons allow you to page through the document, to zoom and to confirm the print-out
Manual S2G_Optimizer
42
V1.0
Your partner in finding solutions
3.11.Options 3.11.1. Optimisation of panels (2D) All options with regard to the optimisation method are saved per project!
Calculation method :
3.11.1.1.
Surface
This method puts the biggest piece first. This also applies for the remaining part. Again, the biggest possible piece(s) will be placed first.
Manual S2G_Optimizer
43
V1.0
Your partner in finding solutions 3.11.1.2.
Waste
This method puts the piece that creates the least waste in terms of absolute surface (m²) first. This also applies for the remaining part. Again, the piece that creates the least waste in terms of absolute surface (m²) will be put first.
This piece (0.9m x 0.4m) generates a waste of 0.2m x 0.4m = 0.08m²
This piece (1m x 0.9m) generates a waste of 0.1m x 0.9m = 0.09m²
Manual S2G_Optimizer
44
V1.0
Your partner in finding solutions 3.11.1.3.
In terms of “percentage”
This method puts the piece that creates the least waste in terms of relative surface (%) in relation to itself first. This applies for the remaining part as well. Again, the piece that creates the least waste in terms of relative surface (%) in relation to the piece itself will come first.
This piece (1m x 0.9m) generates a relative waste of (0.1x0.9)/(1x0.9)*100 = 10%
This piece (0.4m x 0.9m) generates a relative waste of (0.7x0.9)/(0.4x0.9)*100 = 175%
Manual S2G_Optimizer
45
V1.0
Your partner in finding solutions 3.11.1.4.
Fast <> Precise
The accurate method brings about more iterations. This prolongs the total calculation time but improves the total result.
3.11.1.5.
Optimisation of cuts
In some cases, it can be more interesting (less time-consuming) to limit the total saw-cut in stead of limiting the total waste. This is possible with S2G_Optimizer: group all pieces with at least one equal dimension. However, it makes sure that the group still fits in the panel. The more pieces you can group the less saw-cut you will need.
These 5 pieces are grouped and optimised together.
3.11.1.6.
Longest cut
This option sets the maximum saw-cut [mm] of the machine.
Manual S2G_Optimizer
46
V1.0
Your partner in finding solutions
3.11.2. Optimisation of profiles (1D) All options concerning the optimisation method are saved for each project separately! The accurate method brings about more iterations. This prolongs the total calculation time, however, improves the total result.
3.11.3. Screen presentation
Manual S2G_Optimizer
47
V1.0
Your partner in finding solutions
3.11.4. Print preview You can change the printer margins[mm] in “printer properties”. You can also indicate the number of panels that have to be printed out horizontally and vertically.
3.11.5. Languages
Manual S2G_Optimizer
48
V1.0
Your partner in finding solutions
3.11.6. Import of CSV-files You can define one or more file formats. These ASCII-files can be imported into an empty project.
-
Delimiter First row containing data Filter, only import data with value Filter, only import data with value Column length Column width Column height Column quantity Column left angle Column right angle
= “,” =2 = 5 in column 1 (option) = 26v in column 2 (option) = col. 0 ( does not apply to panels) = col. 5 (does not apply to profiles) = col. 6 (does not apply to profiles) = col. 4 = col. 0 (does not apply to panels) = col. 0 (does not apply to panels)
Ex. : The preceding settings of a CSV-format (Comma Separated Values) are correct to import the following – ASCII-file : "INFO","test1","diverse","Manufacturing","C:\Facalog\Projects\Project.jpg" "1","52A10","CAPPING PROFILE","14","7000","1048599","1048599" "1","52R52","MULLION","6","7000","1048679","1048679" "1","PV001","THERMAL BREAK","23","7000","","" "2","52R223","GASKET","25","7000" "2","52R226","GASKET","4","7000" "3","83Z639","SCREW","40" "5","20v","","1","1403","1202","0","0","0" "5","20v","","1","1478","1202","0","0","0" "5","20v","","1","1478","1202","0","0","0" "5","20v","","1","1452","1202","0","0","0" "5","20v","","1","1478","1228","0","0","0" "5","20v","","1","1452","1228","0","0","0" "5","20v","","1","1403","1202","0","0","0" "5","20v","","1","1403","1228","0","0","0" "5","20v","","1","1478","1202","0","0","0" "5","20v","","1","1478","1228","0","0","0" "5","20v","","1","1478","1202","0","0","0" "5","20v","","1","1478","1228","0","0","0" "5","20v","","1","1452","1202","0","0","0"
Manual S2G_Optimizer
49
V1.0