Installatiecertificaat

Installatiecertificaat BRL-K903:07

Registratienummer 100902267

Opdrachtgever

Installateur

Rolf Janssen GmbH

Hamer Installatietechniek B.V.

Emsstrasse 4 (B 72)

Stadhoudersmolenweg 23

26603

7317 AV APELDOORN Tel: 055-5777200

AURICH DUITSLAND

Fax:

055-5777202

Email:

[email protected]

Plaats van inrichting Restastoffenenergiecentrale

Uitvoerder

Validatie

Langelijnbaan 14

Schenkel, Lucas

Lankhorst, Albert

Datum uitvoering

Opleverdatum

23-09-2010

18-11-2010

8861 NW

Harlingen

Hoofdgebied: D Tank nr 1

Producent Tolsma

Tank nummer 10CDW3186

Inhoud

Product

Product

Herkeur

in m3

handelsnaam

WMS categorie

jaar

8

gasolie

brandbaar

2025

Opmerkingen:

Wenken voor de afnemer Bij het ontvangst van het installatiecertificaat controleren of dit volledig is ingevuld en voorzien van een registratienummer.

Kiwa Nederland B.V. Sir Winston Churchill-laan 273 Postbus 70, 2280 AB Rijswijk Telefoon 070 41 44 400 Telefax 070 41 44 420 Internet www.kiwa.nl

Indien de installatie of certificaat niet in orde wordt bevonden, dient u contact op te nemen met: 1. De installateur; 2. Kiwa Nederland B.V. Algemeen Een tankinstallatie voldoet aan wet- en regelgeving indien: Naast het installatiecertificaat ook een tankcertificaat is afgegeven. Aanpassingen en/of wijzigingen aan de tankinstallatie mogen alleen worden uitgevoerd door gecertificeerde bedrijven op basis van de BRL-K903. Dit certificaat vervalt indien niet aan bovenstaande wordt voldaan.

Datum:

22-3-2011

Pagina 1 van 2

Registratienummer

100902267

Installatiecertificaat BRL-K903:07

Registratienummer 100902267 Nadere omschrijving en eigenschappen van de installatie Reden

: Gewijzigd certificaat

Tankmateriaal

: Staal

Tankwand

: Dubbelwandig

Tankcoating (inwendig)

: Nee

Tankcoating (uitwendig)

: Verf C3

Leidingsituatie

: Bovengronds

Leidingmateriaal

: Thermoplast kunststof

Leidingverbindingen

: Fitwerk

Leidingwand

: Dubbelwandig

Leidingcoating

: Ja, : kunststof

Persleidingen

: Nee

Mantelbuis

: Nee

Bodemweerstandmeting

: Niet noodzakelijk

Kathodische Bescherming

: Niet nodig

Antihevelklep

: Ja, Steenbergen

Dampretour appendages

: Nee

Vulpuntbak

: Ja, Tolsma

Overvulbeveiliger

: Volgens BRL-K 636 : cleanfill 1010-086

Tankbak

: NVT

Lekdetectiesysteem

: Ja

Lekdetectiemedium

: Vloeistof

Niveau meetsysteem

: NVT

Verklaring ontwerpbeoordeling

: NVT

Afwijkingen

: Nee

Explosieveiligheidsdocument

: NVT

Over-/onderdrukveiligheden

: Nee

Verklaring van Kiwa Nederland B.V. Op grond van onderzoek, alsmede regelmatig door Kiwa uitgevoerde audits, worden door bovengenoemde installateur geïnstalleerde installatie geacht te voldoen aan de Kiwa beoordelingsrichtlijn BRL-K903:07.

Verklaring van de installateur De installateur verklaart dat de installatiewerkzaamheden en controles zijn uitgevoerd in overeenstemming met de voorschriften zoals die zijn vastgelegd in beoordelingsrichtlijn BRL-K903:07.

Wenken voor de afnemer Bij het ontvangst van het installatiecertificaat controleren of dit volledig is ingevuld en voorzien van een registratienummer.

Kiwa Nederland B.V. Sir Winston Churchill-laan 273 Postbus 70, 2280 AB Rijswijk Telefoon 070 41 44 400 Telefax 070 41 44 420 Internet www.kiwa.nl

Indien de installatie of certificaat niet in orde wordt bevonden, dient u contact op te nemen met: 1. De installateur; 2. Kiwa Nederland B.V. Algemeen Een tankinstallatie voldoet aan wet- en regelgeving indien: Naast het installatiecertificaat ook een tankcertificaat is afgegeven. Aanpassingen en/of wijzigingen aan de tankinstallatie mogen alleen worden uitgevoerd door gecertificeerde bedrijven op basis van de BRL-K903. Dit certificaat vervalt indien niet aan bovenstaande wordt voldaan.

Datum:

22-3-2011

Pagina 2 van 2

Registratienummer

100902267

Tankcertificaat BRL-K796/02 Bovengrondse horizontale cilindrische stalen tanks tot 150 m³ voor de drukloze opslag van vloeistoffen

Opdrachtgever

Fabrikant/leverancier

Rolf Janssen GmbH

Tolsma Tankbouw B.V.

Emstrasse 4 (B 72)

IJzerweg 1 c

26603

8445 PK HEERENVEEN Tel: 0513-633733

Aurich Duitsland

Fax:

0513-633490

Email:

[email protected]

Registratienummer

Registratiedatum

101101488

15-11-2010

Tanknummer:

Conform:

10CDW3186

Toepassingsgebied I

Tankgegevens Bouwjaar

2010

Inhoud (l)

8000

Compartimenten (l)

nee

Lengte (mm)

4350

Diameter (mm)

1600

Leeg gewicht (kg)

1950

Wand

Dubbel

Materiaal

Staal

Uitwendige coating (C3)

lak 9005

Inwendige coating Klasse

B

Type lekdetectie

vloeistof

SG Max.

1.9

* Voldoet minimaal aan omgevingsconditie C3 conform ISO 12944-2

Verklaring van Kiwa Nederland B.V. Op grond van onderzoek, alsmede regelmatig door Kiwa uitgevoerde audits, worden door bovengenoemde fabrikant uitgevoerde producten geacht te voldoen aan de Kiwa beoordelingsrichtlijn BRL-K796/02.

Verklaring van de fabrikant/leverancier De fabrikant verklaart dat de fabricagewerkzaamheden zijn uitgevoerd in overeenstemming met de voorschriften zoals die zijn vastgelegd in beoordelingsrichtlijn BRL-K796/02.

Algemeen Naast het tankcertificaat moet een installatiecertificaat worden afgegeven om een tankinstallatie aan de wet- en regelgeving te laten voldoen. Verklaring toepassingsgebieden: I : conform EN12285-2:2005 en BRL K796/02 §3.1 II : conform BRL K796/02 §4.1 III : conform BRL K796/02 §5.1 IV : conform BRL K796/02 §6.1

Wenken voor de afnemer Bij ontvangst van het tankcertificaat controleren of: - Het serienummer op de tank overeenkomt met dit certificaat. - De tank geen zichtbare transportschade heeft opgelopen. Indien op grond van bovenstaande of andere redenen de tank niet in orde wordt bevonden, dient u contact op te nemen met: 1. De leverancier van de tank. 2. Kiwa Nederland B.V.

Validatiedatum

15-11-2010

Kiwa Nederland B.V. Sir Winston Churchill-laan 273 Postbus 70, 2280 AB Rijswijk Telefoon 070 41 44 400 Telefax 070 41 44 420 Internet www.kiwa.nl Een exemplaar van dit certificaat is bestemd voor: Bevoegd gezag, eigenaar, fabrikant, Kiwa.

Registratienummer

101101488

Number

K45726/02

Replaces

K45726/01

Issued

2009-05-01

Dated

2008-01-01

Technical Approval with Product Certificate

Underground thermoplastics piping systems Based on pre-certification tests as well as periodic inspections by Kiwa, the products referred to in this certificate and marked with the Kiwa-mark as indicated under 'Marking', manufactured by

OPW Fueling Containment Systems may, on delivery, be relied upon to comply with the Kiwa Evaluation Guideline BRL-K552/02 “Underground thermoplastics piping systems for the transport of liquid oil products and their vapours”.

ing. B. Meekma Director Kiwa N.V.

This certificate is issued in accordance with the Kiwa-Regulations for Product Certification. This certificate consists of 5 pages. Publication of the certificate is allowed.

Kiwa N.V. Sir W. Churchill-laan 273 P.O. Box 70 2280 AB RIJSWIJK ZH The Netherlands

Company OPW Fueling Containment Systems 3250 US 70 Business West SMITHFIELD NC 27577-0330 North Carolina USA

Tel. +31.70-4144 400 Fax +31.70-4144 420 E-mail [email protected] www.kiwa.nl

Phone Fax Internet

+1.919-9342 786 +1.919-3593 687 www.opwfcs.com

Distributor TSE Fueling Supplies B.V. Koggewagen 60 1261 KD BLARICUM

The Netherlands Phone +31.355-256 976 Fax +31.355-259 641 Internet www.tseonline.nl

2

Page

Number

K45726/02

Replaces

K45726/01

Issued

2009-05-01

Dated

2008-01-01

Underground thermoplastics piping systems for the transport of liquid oil products and their vapours CONTENTS 1.

Application and use

2.

Technical Specification

3.

Installation

4.

Performance

5.

Maintenance

6.

Recommendations for the installer

7.

List of documents

APPLICATION AND USE General

Ventilation requirements

The piping systems complying with this Evaluation Guideline are suitable

To satisfy the Dutch environmental regulations, it is required that the

for the transport of liquid oil products with a flash-point of

interstitial space between the primary and secondary pipe of the product

– 20 up to + 50ºC for tank installations according to Kiwa Evaluation

lines is ventilated. A ventilation unit controls this ventilation. The unit

Guideline BRL-K903.

consists of an electrically driven vacuum pump. This pump is developed, tested and approved for pumping air mixed with explosive vapours of

Application

liquid petrol.

The piping system is suitable for use in fuel applications where the

The unit must be explosion proof and equipped with an explosion proof

maximum speed of the liquid does not exceed 5 m/s. They may be used

motor.

as a suction line with a negative pressure of a minimum of

The unit can be placed in the dispenser, in the above ground filling point

0.8 bar (0.2 bar absolute) or a positive working pressure of 5.0 bars.

cabinet, in a separate box placed on the fluid tight pavement or in a

NOTE 1: For liquid products other than diesel oil, unleaded and leaded

separate box in which case the pump exhaust is connected to a 5m vent

petrol the test liquids and the requirements for the chemical resistance and stack with flame arrestor above ground level. In all cases proper resistance to permeation shall be adapted.

ventilation has to be provided. The inlet of the unit is connected to a

NOTE 2: At the moment of issue of this Evaluation Guideline the following

system of nylon tubing meeting DIN 73378 of sufficient diameter to allow

pressures are common in pressure systems:

an adequate flow of environmental air into the interstitial space of the

working pressure: 2.5 bars,

product lines. Possible permeation vapours can be extracted at the

rest pressure: 0.9 bar.

pump outlet. Optionally, a gas operated leak detection system on the unit may be used.

Life Expectancy

The unit is dimensioned to provide a functional requirement of a

The product shall have a life expectancy of 20 years.

minimum of 20 litre/hr of air with possible vapours per product line. Product pipes for petrol shorter than 20 m and diesel do not have to be

Leak detection unit

connected to a ventilation unit.

Pressure systems must to be equipped with a leak detection system

Filling and venting lines do not need a ventilation unit.

recommended by the pipe manufacturer and capable of monitoring all sections of the pipeline according to Kiwa Evaluation Guideline BRL-K910.

3

Page

Number

K45726/02

Replaces

K45726/01

Issued

2009-05-01

Dated

2008-01-01

Underground thermoplastics piping systems for the transport of liquid oil products and their vapours TECHNICAL SPECIFICATION General

For vapour recovery is used:

Thermoplastic pipe systems for underground transport of liquid petroleum

Pipes

products according to the Kiwa Evaluation Guideline

- ¾”

BRL-K552: ‘Underground thermoplastic piping systems for the transport of

- 1”

Geoflex type GFP–2100,,double wall, ID ø 25mm

liquid oil products and their vapours’.

- 1½”

Geoflex type GFP–1150, single wall, ID ø 38 mm

Geoflex type GFP–2075, double wall. ID ø 19 mm

- 2”


Application

- 3”


This piping system is suitable to transport fuels like diesel and

- 4”

Geoflex type GFP–1400, single wall, ID ø 89 mm.

gasoline/petrol according to class K1, K2 and K3 of the PGS documents.

Couplings

This piping system is suitable for both suction systems as well as pressure

- OPW type SPC–0075 for¾” pipe

systems with a maximum working pressure of 5.0 bars. This pipe system

- OPW type SPC–0100 for 1” pipe

is not allowed for LPG.

- OPW type BMA–1515 for 1½” pipe - OPW type BMA–2020 for 2” pipe

Description of the system

- OPW type BMA–3030 for 3” pipe

General


The OPW pipe system is a single wall or a double wall pip system that is used for the transport of petroleum products. Product lines are typically a

For vents is used:

double wall pipe system with an integrated secondary pipe. There are

Pipes

some applications that use single wall pipes for product lines as well (see

- 2”

note 1). The vapour recovery pipes and fill pipes are normally single wall

Couplings

pipe.

- OPW type BMA–2020


The interstitial space between primary and secondary pipe is ventilated. Any gases vapour that may permeate from the primary pipe may be

For filling is used:

dispersed by the connection of an approved ventilation system. For the

Pipes

connections to the tank and to the pumps, only certified fittings must be

- 3”


used.

- 4”


Piping systems

Couplings

For suction pipes and pressure pipes, 3 types of primary single wall piping


systems and 3 types of secondary double wall piping may be used:


Pipes The primary pipe is made of polyethylene reinforced with a polyester

- 1½”

Geoflex type GFP–1150, ID ø 38 mm – single wall

- 2”


braid and a special inner layer to reduce the permeation of liquid oil

- 3”


products. The integrated secondary pipe is made of polyethylene and a

- 1½”

Geoflex type GFP–2150, ID ø 38 mm – double wall

protective outer layer of nylon.

- 2”


The colour of the primary pipe is white or natural.

- 3”


The colour of the secondary pipe is green or blue.

Couplings

The colour of the vent pipe is orange or blue.

- OPW type BMA–1515 for 1½” single wall pipe - OPW type BMA–2020 for 2” single wall pipe

Fittings

- OPW type BMA–3030 for 3” single wall pipe

Per pipe length between tank and pump island a maximum of 3 fittings

- TSE type CSC–1515 for 1½” double wall pipe

are used. In the product pipe itself no intermediate fittings are used. In

- TSE type CSC–2020 for 2” double wall pipe

vapour recovery pipes intermediate fittings are allowed.

- TSE type CSC–3030 for 3” double wall pipe Note 1: Dutch legislation stipulates the use of a leak detection system for

Standard pipe lengths

pressure applications. This means that in The Netherlands, for pressure

Pipes may be supplied in boxes or coiled reels dependant upon product

applications, only double wall piping systems equipped with a leak

type. Standard lengths (depending on the diameter) are 60, 75, 150 and

detection unit can be used.

300 m.

Note 2: For suction pipes for Diesel and Petrol up to 20m length, single wall piping systems can be used.

4

Page

Number

K45726/02

Replaces

K45726/01

Issued

2009-05-01

Dated

2008-01-01

Underground thermoplastics piping systems for the transport of liquid oil products and their vapours Marking

The marking must contain:

The products will be marked with the Kiwa logo. For the different products to be carried out as follows:

Pipes the Kiwa logo

Pipes

-

the word “Geoflex” on the product pipe

Un-erasable by ink, at least 1 imprint every 2 m.

-

the word “Geovent” on the vapour/vent pipe

-

product date or product code.

Fittings Un-erasable by impact or etching, or clearly marked on the package.

INSTALLATION Certified installers

Installation

The OPW piping systems have to be installed by a Kiwa certified installer

The installation instructions contain notes for storage, transport and the

according to Kiwa Evaluation Guideline BRL-K903 ”Certification scheme

installation itself.

for Installers of Tank Installations (REIT)”. During installation care should be taken to install the ventilation system Installation-instructions

properly. The correct operation of the system can be checked using a

OPW Fueling Containment Systems provides installation instructions in

flow meter.

Dutch which can be found on the company web site www.opwfcs.com. Any change in these instructions will be notified to Kiwa.

Minimum bending radius

The instructions shall contain: -

installation instructions,

The following minimum bending radius per pipe should be respected: ¾” Geoflex, type GFP–2075: 450 mm

-

inspection instructions, and

-

1½” Geoflex, type GFP–1150:

600 mm

-

maintenance instructions.

-

1½” Geoflex, type GFP–2150:

600 mm 900 mm

-

2”

Geoflex, type GFP–1200:

Trained personnel

-

2”


900 mm

The pipe may only be installed by trained installers who have a valid

-

2”

Geoflex, type GVE–1200:

900 mm

training and ID card. Installer training is valid for two years.

-

3”


1200 mm

Training may only be given to installers by a competent nominated

-

3”


1200 mm

employee of OPW FCS or its nominated trainer. Storage Persons providing training to installers must be OPW FCS trained.

It is advised to protect the pipe from long term exposure to direct

Trainers posses a valid certificate confirming their being a registered

sunlight (UV-light) and to install the pipe within a couple of weeks after

Trainer.

delivery to the site of construction.

Trainers are re-assessed annually.

5

Page

Number

K45726/02

Replaces

K45726/01

Issued

2009-05-01

Dated

2008-01-01

Underground thermoplastics piping systems for the transport of liquid oil products and their vapours PERFORMANCE Suction system

Pressure system

Operating pressure

Operating pressure

The working pressure in the system during normal operating conditions is

The working pressure in the system during normal operating conditions

0, 2 bar absolute.

is max 5, 0 bar.

Rest pressure

Rest pressure

When there is no product flow the pressure in the primary pipe will be 0.5

When there is no product flow the pressure in the primary pipe will be

bars maximum.

between 0.9 and 2.2 bar. Permeation Permeation-research and subsequent calculations have shown that the system (the pipe system between tank and dispensing pump) meets the requirements as formulated in the Kiwa Evaluation Guideline BRL-K552.

MAINTENANCE Maintenance and inspection

The PCU has to be checked yearly by a certified installer according

To check the good operation of the system of Environ the 15-yearly

Kiwa Evaluation Guideline BRL-K903.

inspection is sufficient. In this case the complete tank installation is pressure tested.

RECOMMENDATIONS FOR THE INSTALLER 1.

Check the product at the time of delivery according to the paragraph

3.

If you should reject a product on the basis of the above, please

“Technical specification” to ensure that:

contact:

1.1 the producer has delivered in accordance with the

3.1 OPW Fuel Containment Systems or TSE and, if necessary,

agreement;

3.2 Kiwa N.V.

1.2 the mark and the marking method are correct; 1.3 the products show no visible defects as a result of transport etc.

4.

Carry out storage, transport and installation according to the paragraph “Installation”.

2.

Check whether the products meet the specifications according to section general, pipes and fittings of the paragraph “Technical

5.

specification”.

Take the information from the paragraph “Performance” into consideration.

LIST OF DOCUMENTS -

Kiwa Evaluation Guideline BRL-K903: “Certification scheme for

-

Kiwa Guideline for product certification.

Installers of Tank Installations (REIT)”. -

Kiwa Evaluation Guideline BRL-K552: “Underground thermoplastic

The exact dates of publication of above mentioned documents can be

piping systems for the transport of liquid oil products and their

found in the Kiwa Evaluation Guideline BRL-K552.

vapours.

Installatiecertificaat

Recommend Documents